Connecting Amplifier Or System Component; To Enjoy Multi-Channel Surround Sound On Dvd-Video (Digital Connection); Connection To A Stereo Amplifier (Analog Connection); Dvd Output And Dvd/Vhs Output - Panasonic DMR-E75VS Operating Instructions Manual

Before Use

Connecting amplifier or system component

∫ To enjoy multi-channel surround sound on
DVD-Video (digital connection)
Connect an amplifier with a built-in decoder
with these logo marks.
≥Use an optical digital audio cable.
≥Change the settings in "Digital Audio Output" (l 44).
≥You cannot use DTS Digital Surround decoders not suited to DVD.
≥Even if using this connection, output will be only 2 channels when
playing DVD-Audio
(1) Rear panel of this unit
(2) Insert fully, with this side
facing up. (Do not bend when
connecting.)
(3) Optical digital audio cable
(not supplied)
(4) To optical digital input
(5) Amplifier's rear panel

DVD output and DVD/VHS output

This unit has DVD/VHS COMMON output terminals which are
common to both DVD and VHS, and DVD output terminals which are
exclusively used for DVD.
DVD/VHS COMMON output
Y P P
B R
COMPONENT VIDEO OUT
(480P/480I)
OPTICAL
DIGITAL AUDIO OUT
(PCM/BITSTREAM)
DVD OUT
DVD output
≥For DVD/VHS COMMON output terminals, both DVD and VHS
outputs can be switched.
≥The DVD output terminals can only output the DVD signal.
≥Even if "Automatic" is selected in "DVD/VHS Output" on
"Set Up" Menu (l 43), the desired output may not be selected
depending on the operation. In this case, press [DVD/VHS
OUTPUT] on the remote controller to switch manually.
≥When the Video is switched from DVD to VHS or vice versa,
the audio volume may suddenly increase or decrease. This is
because when the audio output of this unit is connected to the
TV or other, the audio output of the DVD is generally lower.
When you increase the volume level of the TV or the amplifier
to play back DVD audio, reduce it when playback is finished.
(1)
Y P P
B R
COMPONENT VIDEO OUT
(480P/480I)
OPTICAL
DIGITAL AUDIO OUT
(PCM/BITSTREAM)
(2)
(3)
OPTICAL IN
(4)
(5)
DVD/VHS COMMON OUT
R - AUDIO - L VIDEO
R - AUDIO
R - AUDIO - L VIDEO S-VIDEO
Dolby Digital (l 44)
This is a method of coding digital signals developed
by Dolby Laboratories. Not only stereo (2 channel)
audio, these signals can also be 5.1-channel audio.
A large amount of audio information can be
recorded on one disc by this method.
DTS Digital Surround (l 44)
This surround system is used in many movie
theatres around the world. The separation between
channels is good and the compression ratio is low,
so realistic sound effects are possible.
DTS sound tracks are produced with the assumption
that all channels will be used.
R - AUD
∫ Connection to a stereo amplifier
(analog connection)
R - AUD
DVD OUT
(1) Rear panel of this unit
(2) To AUDIO OUT (L/R)
(3) Audio cable (not supplied)
A Red (R)
B White (L)
(4) Audio input (L/R)
(5) Amplifier's rear panel
Preparation
≥Press [DVD].
[1]
While stopped
Press [FUNCTIONS].
[2] Select "SETUP" with [3, 4, 2, 1] and press
[ENTER].
Select "Set Up" with [3, 4] and press [2, 1].
[3]
Select "DVD/VHS Output" with [3, 4] and press
[4]
[ENTER].
[5] Select "Automatic" or "Manual" with [3, 4] and
press [ENTER].
12
(1)
P P DVD/VHS COMMON OUT
B R
R - AUDIO - L VIDEO
(2)
COMPONENT VIDEO OUT
(480P/480I)
OPTICAL
ITAL AUDIO OUT
CM/BITSTREAM)
R - AUDIO - L VIDEO
DVD OUT
(3)
R L
AUDIO IN
(4)
(5)
(l 47)
S-VIDEO