Table of Contents
Advertisement
Problem
The appliance is not in operation. A cook-
ing time is shown in the display
and
:
light up in the display
0
‹
‹‹
The
indicator appears even though the
¯
water tank is full
The
indicator appears even though the
¯
water tank is not yet empty, or the water
tank is empty but the
¯
indicator does not
appear
The water tank empties for no discernible
reason. The evaporator dish overflows
The evaporator dish has boiled empty
even though the water tank is full.
The
indicator appears
¯
There is a "pop" noise during cooking
When you cook with steam, a lot of steam
is created
When cooking with steam, a lot of steam is
created again
Steam escapes from the ventilation slots
during cooking
The appliance is not producing steam
properly
Error message
appears in the dis-
"‹‚‚
play
An
... error message appears in the dis-
"
play
The appliance is no longer heating. The
colon flashes in the display
Replacing the cooking compartment bulb
Heat-resistant 25 W, 220/240 V bulbs, E14 bulb sockets and
the seals are available from the after-sales service. Please
specify the E number and FD number of your appliance.
:
Risk of burns!
Allow the cooking compartment and cooking compartment light
to cool before changing the bulb.
Switch off the fuse in the fuse box or unplug at the mains.
1.
Turn the cover anti-clockwise to remove.
2.
Screw out the bulb by turning it anti-clockwise and replace
3.
with a bulb of the same type.
18
Possible cause
A control knob was unintentionally
pressed
The
|
button was not pressed after
J
"
setting
Power cut
The water tank has not been inserted
properly
The detection system is not working
The water tank is dirty. The moving water
level indicators are jammed
The water tank was not closed properly
The tank lid seal is dirty
The tank lid seal is defective
The water tank has not been inserted
properly
The feed line is blocked
The appliance has not been used for at
least 2 days and the water tank is full
Cold/warm effect with frozen food, caused
by the steam
The appliance is being automatically cali-
brated
The appliance is unable to calibrate itself
automatically if cooking times are too
short
Limescale has formed in the appliance
A button was pressed for too long or is
jammed
Technical fault
A button combination was pressed
Slide the new seals and the clamping ring onto the glass
4.
cover in the right order.
Screw the glass cover with the seals back on again.
5.
Connect the appliance to the mains and reset the clock.
6.
Never operate the appliance without the glass cover and seals.
Notes/remedy
Press and hold the
J
|
"
Press the
|
button briefly to start the
J
"
cooking operation, or press and hold the
|
button to cancel the setting
J
"
Reset the clock time (see section: Time-
setting options)
Slide in the water tank until it locks into
place.
Call the after-sales service
Shake and clean the water tank. If the
parts cannot be released, obtain a new
water tank from the after-sales service
Close the lid until you feel it lock into place
Clean the seal
Obtain a new water tank from the after-
sales service
Slide in the water tank until it locks into
place
Descale the appliance. Check whether the
water hardness range is set correctly
Empty and clean the water tank. Always
empty the water tank after cooking
This is normal
This is normal
Reset the appliance to the factory settings
(see Basic settings section). Then start
steaming at 100 °C for 20 minutes
This is normal
Start the Descale programme (see section:
Descaling)
Press the
button to clear the fault mes-
0
sage. Press all of the buttons individually
and check if they are clean
Press the
button to delete the error
0
message. Reset the clock if required. If the
error message appears again, call the
after-sales service
Set the Steam operating mode to 35 °C,
then press and hold the
@
audible signal sounds. Press the
ton again briefly
button
button until an
but-
@
Advertisement
Table of Contents
