Table of Contents
Advertisement
AwARNING
• When speaker output is used by 4
channels, use speakers rated over 50 W
(maximum input
power)
and between 4
Q
to 8 Q (impedance value). Do not use 1 Q
to 3 Q speakers for this
unit.
• When rear speaker output is used by a 2
Q
subwoofer,
use speakers rated for over
?OW.
* Please refer to connections for a
connection method.
• The black cable is ground. When installing
this unit or power amp (sold separately),
make sure to connect the ground wire first.
Ensure that the ground wire is properly
connected to metal parts of the car's body.
The ground wire of the power amp and the
one of this unit or any other device must
be connected to the car separately with
different screws. If the screw for the ground
wire loosens or falls
out,
it could result in
fire,
generation of smoke or
malfunction.
Two devices connected to the
car separately (ground wires)
~
,
,~//Ill
/
/ ~ ~
_<::><::>\-
Metal parts
of car's body
*1 Not supplied for this unit
(!}-Important
• When installing this unit in a vehicle
without an ACC (accessory) position on
the ignition switch, failure to connect
the red cable to the terminal that detects
operation of the ignition key may result in
battery
drain.
ACC position
No ACC position
• Use this unit with a 12-volt battery and
negative grounding only. Failure to do so
may result in a fire or
malfunction.
• To prevent a short-circuit, overheating
or malfunction, be sure to follow the
directions below.
-
Disconnect the negative terminal of the
battery before installation.
-Secure the wiring with cable clamps
or adhesive
tape.
Wrap adhesive tape
around wiring that comes into contact
with metal parts to protect the
wiring.
-Place all cables away from moving parts,
such as the shift lever and seat
rails.
-Place all cables away from hot places,
such as near the heater outlet.
-Do not connect the yellow cable to the
battery by passing it through the hole to
the engine
compartment.
-Cover any disconnected cable connectors
with insulating tape.
-Do not shorten any cables.
-Never cut the insulation of the power
cable of this unit in order to share the
power with other
devices.
The current
capacity of the cable is limited.
-Use a fuse of the rating
prescribed.
-Never wire the negative speaker cable
directly to
ground.
-
Never band together negative cables of
multiple
speakers.
• When this unit is on, control signals
are sent through the blue/white
cable.
Connect this cable to the system remote
control of an external power amp or
the vehicle's auto-antenna relay control
terminal (max. 300mA 12 V DC). If the
vehicle is equipped with a glass antenna,
connect it to the antenna booster power
supply terminal.
• Never connect the
blue/
white cable to
the power terminal of an external power
amp. Also, never connect it to the power
terminal of the auto antenna. Doing so may
result in battery drain or a malfunction.
• The graphical symbol= placed on the
product means direct current.
• The function and audio settings other than
the setting of RCA pre-outs are stored in
memory if the unit is disconnected from
power supply.
This unit
CD
Power cord input
®
Rear output or subwoofer output
@
Antenna input
@
Fuse (10 A)
Power cord
Perform these connections when not
connecting a rear speaker or middle range
speaker lead to a
subwoofer.
......
_,._,.,.,._,..
.........
White
White/
black
Gray
®~
(J)~
®
m
®~
@~
®
-
•
•
Gray/
black
_. __
..............................
Green
Green/
black
Violet
Violet/black
@)~
@~
©
ml
@~
®
mil
@~
.. .............................
@
Black
@
Yellow
@
Red
@ Blue/
white
Advertisement
Table of Contents
