Table of Contents
Advertisement
Doc Title
:
User's Guide
Model
:
Motorola S70×BT
3.21.3 Three-party conference call
1. During an external home call, press <MENU>. -Your call will be put on hold.
2. Press <VOL+> or <REDIAL/VOL-> to select the handset or the speaker pod you want to call.
3. Press <MENU> to call the handset or the speaker pod.
4. When the other handset or the speaker pod answers the intercom call, press <MENU> on the calling handset
to set up the conference call.
5. Press <HOME> on any handset to end a three-party conference call and leave the other handset or the
speaker pod engaged with the caller, or press <TALK ON/OFF> on the speaker pod to hang up and leave the
other handset engaged with the caller.
NOTE
During an external call, pressing <HOME> or <SPEAKER> on any handset, or pressing <TALK ON/OFF> on the
speaker pod will join in the call and set up a conference call.
3.22 Setting the dial mode
The default dialing mode is suitable for your country and network operator. It is unlikely that you should need to
change this setting unless advised to do so.
1.
Press <MENU> and then <VOL+> or <REDIAL/VOL-> to select SETUP BS.
2.
Press <MENU> to select DIAL MODE.
3.
Press <MENU> and then <VOL+> or <REDIAL/VOL-> to select TONE or PULSE.
4.
Press <MENU> to save the setting.
NOTE
If pulse mode is selected, press <*/TONE> to switch from pulse to tone dialing temporarily when dialing out. After
the call is ended, the dial mode will change back to pulse automatically.
3.23 Setting the flash time
The default flash time is suitable for your country and network operator. It is unlikely that you should need to
change this setting unless advised to do so.
1.
Press <MENU> and then <VOL+> or <REDIAL/VOL-> to select SETUP BS.
2.
Press <MENU> and then <VOL+> or <REDIAL/VOL-> to select FLASH TIME.
3.
Press <MENU> and then <VOL+> or <REDIAL/VOL-> to the flash time you want. (8 options are available: 90,
100, 110, 250, 300, 400, 600 and 700MS)
4.
Press <MENU> to save the setting.
3.24 Setting the area code
1.
Press <MENU> and then <VOL+> or <REDIAL/VOL-> to select SETUP BS.
2.
Press <MENU> and then <VOL+> or <REDIAL/VOL-> to select AREA CODE.
3.
Press <MENU> and enter the area code.
4.
Press <MENU> to save the setting.
3.25 Registration
3.25.1 Registering a handset
Up to 5 handsets or speaker pods can be registered to one base. The original handset is pre-registered to use.
Additional handsets must be registered to the base before you can use them.
To register an additional handset,
1.
Press <MENU> and then <VOL+> or <REDIAL/VOL-> to select SETUP HS.
2.
Press <MENU> and then <VOL+> or <REDIAL/VOL-> to select REGISTRATION.
3.
Press <MENU> and then <VOL+> or <REDIAL/VOL-> to select YES or NO.
4.
Select YES and press <MENU> to enter the registration procedure as follows:
1)
Press and hold <FIND> for around 4 seconds on the base, release once IN USE LED is flashing.
2)
Place the unregistered handset on the base or charger.
3)
A confirmation tone is generated if registration is successful. Handset X is displayed where X denotes the
number of handsets, and then the phone returns to idle.
To register an originally unregistered handset, follow steps 1) through 3) above.
This document contains confidential and proprietary information of VTech Telecommunications Ltd
Revision :
Page(s) :
1.0
20 of 29
Advertisement
Table of Contents
