Electrical Safety; Personal Safety - Skil BT1-1310 Series Original Instructions Manual

a
Sliding mitre saw
INTRODUCTION
This tool is intended as a stationary machine for
•
lengthways and crossways cutting of wood with straight
cuts as well as angle cuts (horizontal mitre angles of -47°
to +47° as well as vertical bevel angles of 0° to 45° are
possible)
• Read and save this instruction manual 2
• This tool is not intended for professional use
• Only use the tool when correctly and completely
assembled (be aware that Skil cannot be hold
responsible for tool damage and/or personal injuries
resulting from the incorrect assembly of the tool)
TECHNICAL DATA 1
TOOL ELEMENTS 8
A Lower guard
B Switch handle
Locking pin for transport
C
D Upper guard
E Transport handle
Mounting holes
F
G Support foot
H Dust bag
J Dust port
Extension bars
K
L Knobs for locking extension bars
M Clamp for mounting workpiece
Support hole
N
P Knob for fastening clamp
Q Knob for adjusting clamp
R Clamping lever
S Fence
T Hex screws for adjusting fence (2x)
U Locking knob (bevel angles)
Bevel angle indicator
V
W Screw for adjusting bevel angle (right)
X Screw for adjusting bevel angle (left)
Laser adjustment screw
Y
Z Laser light
AA On/off switch laser
AB Locking handle (mitre angles)
AC Mitre detent release lever
AD Mitre angle indicator
AE Locking knob for slide device
AF On/off switch
AG Safety lever
AH Cutting depth limiter
AI Depth stop
AJ Depth stop nut
AK Hex key
AL Storage for hex key
AM Spindle-lock button
AN Cover plate screw
AO Blade bolt
AP Flange
AQ Table insert
AR Dust deflector
SAFETY
GENERAL POWER TOOL SAFETY WARNINGS
1310
WARNING Read all safety warnings, instructions,
-
illustrations and specifications provided with this
power tool. Failure to follow all instructions listed below may
result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term "power tool" in the warnings refers to your mains-
operated (corded) power tool or battery-operated (cordless)
power tool.
1) WORK AREA SAFETY
a) Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks which
may ignite the dust or fumes.
c) Keep children and bystanders away while operating
a power tool. Distractions can cause you to lose control.

2) ELECTRICAL SAFETY

a) Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any adapter
plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce risk of
electric shock.
b) Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
d) Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving
parts. Damaged or entangled cords increase the risk of
electric shock.
e) When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a
cord suitable for outdoor use reduces the risk of electric
shock.
f) If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.

3) PERSONAL SAFETY

a) Stay alert, watch what you are doing and use
common sense when operating a power tool. Do not
use a power tool while you are tired or under the
influence of drugs, alcohol or medication. A moment
of inattention while operating power tools may result in
serious personal injury.
b) Use personal protective equipment. Always wear
eye protection. Protective equipment such as a dust
mask, non-skid safety shoes, hard hat, or hearing
protection used for appropriate conditions will reduce
personal injuries.
c) Prevent unintentional starting. Ensure the switch
is in the off-position before connecting to power
source and/or battery pack, picking up or carrying
15