Pioneer MVH-S512BS Operation Manual page 48

FEDERAL COMMUNICATIONS COMMISSION SUPPLIER'S DECLARATION OF
CONFORMITY
Product Name: DIGITAL MEDIA RECEIVER
Model Number: MVH-SS 12BS
Responsible Party Name: PIONEER ELECTRONICS (USA), INC. SERVICE SUPPORT DIVISION
Address: 2050 W. 190TH STREET, SUITE 100 TORRANCE, CA 90504, U.S.A.
Phone: 1-310-952-2915
URL: http://www.pioneerelectronics.com
The Safety of Your Ears is in Your Hands
Get the most out of your equipment by playing it at a safe level-a level that lets the sound come through
clearly without annoying blaring or distortion and, most importantly, without affecting your sensitive
hearing. Sound can be deceiving.
Over time, your hearing "comfort level" adapts to higher volumes of sound, so what sounds "normal" can
actually be loud and harmful to your hearing. Guard against this by setting your equipment at a safe level
BEFORE your hearing adapts.
ESTABLISH A SAFE LEVEL:
• Set your volume control at a low setting.
• Slowly increase the sound until you can hear it comfortably and clearly, without distortion.
• Once you have established a comfortable sound level, set the dial and leave it there.
BE SURE TO OBSERVE THE FOLLOWING GUIDELINES:
• Do not turn up the volume so high that you can't hear what's around you.
• Use caution or temporarily discontinue use in potentially hazardous situations.
• Do not use headphones while operating a motorized vehicle; the use of headphones may create a traffic
hazard and is illegal in many areas.
A
wARNING
• Do not attempt to Install or service this product by yourself. Installation or servicing of this product
by persons without training and experience In electronic equipment and automotive accessories
may be dangerous and could expose you to the risk of electric shock, Injury or other hazards.
• Do not attempt to operate the unit while driving. Make sure to pull off the road and park your vehicle in a
safe location before attempting to use the controls on the device.
• This product contains chemicals known to the State of California and other governmental entities to cause
cancer and birth defects or other reproductive harm. Wash hands after handling.
A
cAUTION
• Do not allow this unit to come into contact with moisture and/or liquids. Electrical shock could result. Also,
damage to this unit, smoke, and overheating could result from contact with liquids.
• Always keep the volume low enough to hear outside sounds.
• This product is evaluated in moderate and tropical climate condition under the Audio, video and similar
electronic apparatus -Safety requirements, IEC 60065.
After-sales service for Pioneer products
Please contact the dealer, distributor from where you purchased this unit or the authorized PIONEER Service
Station for after-sales service or any other information. In case the necessary information is not available,
please contact the companies listed below:
Please do not ship your unit to the companies at the addresses listed below for repair without contacting
them in advance.
U.S.A. and CANADA
Pioneer Electronics (USA) Inc.
CUSTOMER SUPPORT DIVISION
P.O. Box 1760
Long Beach, CA 90801-1760
800-421-1404
For warranty information please see the Limited Warranty sheet included with this unit.
In the following, "NW" represents network mode
and "STD" represents standard mode. According to
the connections you have established, change the
speaker mode to standard mode (STD) or network
mode(NW).
A
wARNING
• When speaker output is used by 4 channels, use
speakers rated over 50 W (maximum input power)
and between 4
n
to 8
n
(impedance value). Do
not use
1
n
to 3
n
speakers for this unit.
• When rear speaker output is used by a 2
n
subwoofer, use speakers rated for over 70 W.
*
Please refer to connections for a connection
method.
• The black cable is ground. When installing this
unit or power amp (sold separately), make sure
to connect the ground wire first. Ensure that
the ground wire is properly connected to metal
parts ofthe car's body. The ground wire ofthe
power amp and the one of this unit or any other
device must be connected to the car separately
with different screws. If the screw for the ground
wire loosens or falls out, it could result in fire,
generation of smoke or malfunction.
Two devices connected to the car
separately (ground wires)
~y$#
\
*1 Not supplied for this unit
c!>-lmportant
Metal parts of
car's body
• When installing this unit in a vehicle without an
ACC (accessory) position on the ignition switch,
failure to connect the red cable to the terminal
that detects operation of the ignition key may
result in battery drain.
ACC position No ACC position
- Use this unit with a 12-volt battery and negative
grounding only. Failure to do so may result in a fire
or malfunction.
• To prevent a short-circuit, overheating or
malfunction, be sure to follow the directions
below.
-Disconnect the negative terminal of the battery
before installation.
-Secure the wiring with cable clamps or adhesive
tape. Wrap adhesive tape around wiring that
comes into contact with metal parts to protect
the wiring.
-Place all cables away from moving parts, such as
the shift lever and seat rails.
-Place all cables away from hot places, such as
near the heater outlet.
-Do not connect the yellow cable to the battery
by passing it through the hole to the engine
compartment.
-Cover any disconnected cable connectors with
insulating tape.
-Do not shorten any cables.
-Never cut the insulation of the power cable of
this unit in order to share the power with other
devices. The current capacity of the cable is
limited.
-Use a fuse oft he rating prescribed.
-Never wire the negative speaker cable directly
to ground.
-Never band together negative cables of multiple
speakers.
• When this unit is on, control signals are sent
through the blue/white cable. Connect this cable
to the system remote control of an external power
amp or the vehicle's auto-antenna relay control
terminal (max. 300mA 12 V DC). If the vehicle is
equipped with a glass antenna, connect it to the
antenna booster power supply terminal.
• Never connect the blue/white cable to the power
terminal of an external power amp. Also, never
connect it to the power terminal of the auto
antenna. Doing so may result in battery drain or
a malfunction.
• The graphical symbol= placed on the
product means direct current.