Description Of The Appliance; Preparing The Appliance; Description Of Control Panel; Setting Up The Appliance - DeLonghi La Specialista EC9335M Instructions Manual

1. DESCRIPTION

1.1 Description of the appliance

(page 3 - A )
A1. Bean container lid
A2. Bean container
A3. Cup tray
A4. Steam dial
A5. Hot water spout
A6. Steam spout
A7. Frothing wand selection ring
A8. Frothing wand
A9. Frothing wand connection nozzle
A10. Cup grille for espresso
A11. Cup grille for glasses or mugs
A12. Drip tray grille
A13. Drip tray
A14. Drip tray water level indicator
A15. Water tank lid
A16. Water tank extraction handle
A17. Water tank
A18. Water softener filter housing
A19. Power cord connector socket
A20. Main switch (ON/OFF)
A21. Boiler outlet
A22. Coffee mill outlet (tamping station)
A23. Tamping lever

1.2 Description of control panel

(page 3 - B )
B1. ON/Standby button
B2. Ground coffee quantity dial
B3. "X2" button: to use the 2 coffees Easy Clean filter
B4. Rinse button
B5. "OK" button: to deliver the beverage/confirm
B6. Hot water button
B7. "My" button: to customise beverage quantity
B8. Mode selector dial:
• Espresso
• Americano
• Coffee
• Descaling
B9. Descale light
B10. Steam ready light
B11. Overtemperature light
B12. Energy saving light
B13. General alarm light
B14. Bean container empty/No Bean container light
B15. No water light
B16. Tamping light
B17. Pressure gauge
1.3 Description of the accessories
(page 2 - C )
C1. Portafilter
C2. Easy Clean filter 1 coffee
C3. Easy Clean filter 2 coffee
C4. "Total Hardness Test" indicator paper
C5. Descaler
C6. Water softener filter (*if present)
C7. Power cord
C8. Tube brush
C9. Milk pitcher

2. PREPARING THE APPLIANCE

Wash all accessories with warm water and washing-up liquid,
then proceed as follows:
1. Insert the Bean container (A2) in the coffee mill (fig. 1).
The container is correctly inserted when the arrow is lined
up with the symbol and you hear a "click";
2. Insert the drip tray (A13) complete with cup grill (A11) and
drip tray grille (A12) (fig. 2);
3. Remove the water tank (A17) (fig. 3) and fill with fresh
clean water, taking care not to exceed the MAX level (fig. 4).
4. Put the tank back in the appliance.
Important: Never operate the appliance without water in the
tank or without the tank.
Please note: You should customise water hardness as soon as possible following the
instructions in section "12.2 Water hardness".

3. SETTING UP THE APPLIANCE

1. Plug the power cord connector (C7) into the socket (A19) at
the back of the appliance (fig. 5), then plug the plug into
the mains socket. Make sure the main switch (A20) at the
back of the appliance is pressed and in the I position (fig.
6);
2. The light corresponding to the button (B6) comes on
and the light (B15) flashes to indicate that you need to
deliver water to fill the circuit (fig. 7);
3. Place a container with a minimum capacity of 100 ml (3.5
oz) under the hot water spout (A5) and Frothing wand (A8)
(fig. 8);
4. Press the button (B6) corresponding to the
9). Delivery begins and stops automatically. Empty the
container.
Before using the machine, you must rinse the internal circuits.
Proceed as follows:
5. Attach the portafilter (C1) complete with filter to the appli-
ance. To attach correctly, align the portafilter handle with
"INSERT" (fig. 10), then turn the handle to the right until it is
aligned in the "CLOSE" position;
7
light (fig.