Pentair Goyen IS Series Products Installation Instructions

IS/ISP SERIES
INTEGRATO SEQUENCER
DESCRIPTION
The Integrato Sequencer (IS & ISP) features integrated controls
intended for use with larger reverse pulse jet filter cleaning
systems. The IS & ISP have been designed to operate across a
wide range of environmental conditions. It is suitable for use with
all types of filters, including bags, cartridges, sintered metal or
ceramic filters.
The IS sequencer operates in continuous mode, whereas the ISP
has a built-in differential pressure sensor, allowing this sequencer
to be demand driven.
IS & ISP may be ordered as the sequencer only or in an enclosure
(polycarbonate).
FEATURES
Low temperature operation −40°C (−40°F)
•
Automatic valve detection.
•
Voltage-free coil error output and a visual indication on the
•
display showing which pilot valve output has an error, enabling
quick fault finding and debugging.
Controls up to 40 pilot valves. Each AC output can have 10 pilot
•
valves connected in parallel, enabling up to 400 pilot valves to be
supported. Each DC output can have 3 pilot valves connected in
parallel between −20°C to 60°C (−4°F to 140°F), enabling up to
120 pilot valves to be supported and 2 pilot valves connected in
parallel between −40°C to 60°C (−40°F to 140°F), enabling up to
80 pilot valves to be supported.
Conforms to the requirements of UL, CE, FCC and RCM.
•
TECHNICAL CHARACTERISTICS & PERFORMANCE
dP Support 0 to 4.5 kPa
Input Voltage AC: 100/240 V @ 50/60 Hz
Output Voltage AC: 100/240 V @ 50/60 Hz (same as input)
DC: 24 V
Maximum Input Power AC IN, AC OUT Model: 225 W
AC IN, DC OUT Model: 65 W
Discrete Solenoid Outputs 12, 20 or 40 outputs
Enclosure Polycarbonate or no enclosure
Protection Rating (Large Polycarbonate: IP 66/67 & NEMA 1, 3, 3S,
Enclosure) 4, 4X, 6, 6P & 12
Protection Rating (Small Polycarbonate: IP65 & NEMA 1, 4, 4X, 12
Enclosure) & 13
−40°C to 60°C (−40°F to 140°F)
Operating Temperature
ON & OFF Time ON: 30 ms to 1000 ms, OFF: 1 s to 1000 s
Inputs Voltage Free: Fan Stop, Low Header Alarm
Outputs Voltage Free: Coil Error.
Analogue Output: 4–20 mA dP signal on
the ISP
©COPYRIGHT Goyen Controls Co. Pty. Ltd.
PRODUCT INSTALLATION INSTRUCTIONS
CIRCUIT BOARD LAYOUT
ISP12
16
3
2
4
1
ISP40
4
16
3
4
1
2
1 AC Input Voltage: Electrical connection to the board. Active, Earth
and Neutral connections. Max. cable size 14–26 AWG.
2 ON:OFF Power Switch: Switch power the board ON and OFF.
3 Fuse (Over Current Protection): Replacement fuse T2.5 A 250 V
(slow blow).
4 Outputs Common Terminal: This is the common terminal for all
the 12 solenoid outputs. Max. cable size 12–22 AWG.
5 Discrete Solenoid Output Terminals: Connect each solenoid wire
to a separate output terminal. Max. cable size 12–22 AWG.
6 Coil Alarm Output (Voltage Free): This output triggers when the
coil fails to pulse correctly. It may indicate a fault with the coil or
wiring to that coil. Max cable size 14–26 AWG.
7 4–20 mA dP Output: This output mirrors the output of the built in
dP sensor in the form of a 4–20 mA signal. (ISP only)
8 Low Header Alarm Input (Voltage Free): This input allows for the
connection of a sensor to monitor the header tank pressure. In
the event the pressure drops below the preset level, the pulsing
cycle is paused. Max. cable size 14–26 AWG.
PAGE 1 of 24
GOYEN IS/ISP SERIES CONTROLLER
DEINE-012
ISSUE: 4 DATE: 04.05.2016
15
14
12
11
10
9
8
7
6
5
15
5
13
12
11
10
9
7
5
13
14
8
6