Toshiba MMD-VNK502HEX1E Installation Manual page 83

Checking the settings of the indoor units
Before handing the system over to the customer, check the addresses and settings of the indoor units, then fill in
the check sheet below. When you have installed a group control system, fill in the check sheet for each system and
for each indoor unit. (You can enter the settings of 4 indoor units in to one check sheet.)
NOTE
For maintenance after installation, fill in the check sheet and hand over this Installation manual to the customer.
 Indoor unit settings check sheet
Indoor unit Indoor unit
Model name Model name
Check the addresses of the indoor units. (For details, see "Advanced control" in this manual.)
(Code: [12] for the system, [13] for indoor units, and [14] for groups)
Line Indoor Group Line
Settings Settings
Did you change the setting for the lighting-up hours of the Filter Sign?
If you did not, put a tick against "No change". If you did, put a tick against the item you selected.
(For details, see "Advanced control" in this manual.)
Lighting-up hours of the Filter Lighting-up hours of the Filter
Sign Sign
(Code: [01]) (Code: [01])
 No change  No change
 None [0000]  None
 150H [0001]  150H
 2500H [0002]  2500H
 5000H [0003]  5000H
 10000H [0004]  10000H
Did you change the setting for the detect temperature shift value? If you did not, select the "No change" checkbox. If you did, select the
checkbox of an item. (For details, see "Advanced Control" in this manual.)
Detect temperature shift value Detect temperature shift value
(Code: [06]) (Code: [06])
 No change  No change
 No shift [0000]  No shift
 + 1 °C [0001]  + 1 °C
 + 2 °C [0002]  + 2 °C
 + 3 °C [0003]  + 3 °C
 + 4 °C [0004]  + 4 °C
 + 5 °C [0005]  + 5 °C
 + 6 °C [0006]  + 6 °C
Did you change the setting for the single operation of the Air to Air Heat Exchanger with direct expansion coil?
If you did not, put a tick against "No change". If you did, put a tick against the item you selected.
(For details, see "Advanced control" in this manual.)
Single operation of the Air to Air Single operation of the Air to Air
Heat Exchanger with direct Heat Exchanger with direct
expansion coil expansion coil
(Code: [31]) (Code: [31])
 No change  No change
 No [0000]  No
 Yes [0001]  Yes
Did you change the setting for the remote controller sensor? If you did not, select the "No change" checkbox. If you did, select the checkbox
of an item. (For details, see "Advanced Control" in this manual.)
Remote controller sensor Remote controller sensor
(Code: [32]) (Code: [32])
 No change  No change
 Do not use [0000]  Do not use
 Use [0001]  Use
163-EN
Indoor unit
Model name
Indoor Group Line Indoor Group Line
Settings
Lighting-up hours of the Filter Lighting-up hours of the Filter
Sign Sign
(Code: [01]) (Code: [01])
 No change  No change
[0000]  None [0000]  None
[0001]  150H [0001]  150H
[0002]  2500H [0002]  2500H
[0003]  5000H [0003]  5000H
[0004]  10000H [0004]  10000H
Detect temperature shift value Detect temperature shift value
(Code: [06]) (Code: [06])
 No change  No change
[0000]  No shift [0000]  No shift
[0001]  + 1 °C [0001]  + 1 °C
[0002]  + 2 °C [0002]  + 2 °C
[0003]  + 3 °C [0003]  + 3 °C
[0004]  + 4 °C [0004]  + 4 °C
[0005]  + 5 °C [0005]  + 5 °C
[0006]  + 6 °C [0006]  + 6 °C
Single operation of the Air to Air Single operation of the Air to Air
Heat Exchanger with direct Heat Exchanger with direct
expansion coil expansion coil
(Code: [31]) (Code: [31])
 No change  No change
[0000]  No [0000]  No
[0001]  Yes [0001]  Yes
Remote controller sensor Remote controller sensor
(Code: [32]) (Code: [32])
 No change  No change
[0000]  Do not use [0000]  Do not use
[0001]  Use [0001]  Use
Indoor unit
Model name
Check the addresses of the indoor units. (For details, see "Advanced control" in this manual.)
(Code: [12] for the system, [13] for indoor units, and [14] for groups)
Line Indoor
Settings
Did you change the setting for the imbalance ventilation operation?
If you did not, put a tick against "No change". If you did, put a tick against the item you selected.
(For details, see "Advanced control" in this manual.)
Imbalance ventilation operation
(Code: [48])
 No change
 Normal [0000]
Indoor unit
 SA (High) > [0001]
EA (Low)
Model name
active
 SA (Low) < [0002]
EA (High)
active
Indoor Group
* "High" may be "Extra High".
Did you change the setting for the nighttime heat purge operation?
Settings
If you did not, put a tick against "No change". If you did, put a tick against the item you selected.
(For details, see "Advanced control" in this manual.)
Nighttime heat purge operation
(Code: [4C])
 No change
 Nighttime [0000]
heat purge
OFF
 Start after [0001]-
[0000]
the setting [0048]
[0001]
value x 1
[0002]
hour(s)
[0003]
Did you change the setting for the linked operation with external devices?
[0004]
If you did not, put a tick against "No change". If you did, put a tick against the item you selected.
(For details, see "Advanced control" in this manual.)
Setting of the linked operation
with external devices
(Code: [4E])
 No change
[0000]
 ON/OFF [0000]
[0001]
linked
[0002]
 ON linked [0001]
[0003]
 OFF linked [0002]
[0004]
Did you change the setting for changing the ventilation mode?
[0005]
If you did not, put a tick against "No change". If you did, put a tick against the item you selected.
[0006]
(For details, see "Advanced control" in this manual.)
Changing the ventilation mode
(Code: [EA])
 No change
[0002]
 Heat
exchange
mode
 Automatic [0003]
mode
[0000]
Compatible with RBC-AMT32E
[0001]
[0000]
[0001]
– 82 –
Indoor unit Indoor unit
Model name Model name
Group Line Indoor Group Line Indoor
Settings Settings
Imbalance ventilation operation Imbalance ventilation operation
(Code: [48]) (Code: [48])
 No change  No change
 Normal [0000]  Normal [0000]
 SA (High) > [0001]  SA (High) > [0001]
EA (Low) EA (Low)
active active
 SA (Low) < [0002]  SA (Low) < [0002]
EA (High) EA (High)
active active
* "High" may be "Extra High". * "High" may be "Extra High".
Nighttime heat purge operation Nighttime heat purge operation
(Code: [4C]) (Code: [4C])
 No change  No change
 Nighttime [0000]  Nighttime [0000]
heat purge heat purge
OFF OFF
 Start after [0001]-  Start after [0001]-
the setting [0048] the setting [0048]
value x 1 value x 1
hour(s) hour(s)
Setting of the linked operation Setting of the linked operation
with external devices with external devices
(Code: [4E]) (Code: [4E])
 No change  No change
 ON/OFF [0000]  ON/OFF [0000]
linked linked
 ON linked [0001]  ON linked [0001]
 OFF linked [0002]  OFF linked [0002]
Changing the ventilation mode Changing the ventilation mode
(Code: [EA]) (Code: [EA])
 No change  No change
[0002] [0002]
 Heat  Heat
exchange exchange
mode mode
 Automatic [0003]  Automatic [0003]
mode mode
Compatible with RBC-AMT32E Compatible with RBC-AMT32E
Indoor unit
Model name
Group Line Indoor Group
Settings
Imbalance ventilation operation
(Code: [48])
 No change
 Normal [0000]
 SA (High) > [0001]
EA (Low)
active
 SA (Low) < [0002]
EA (High)
active
* "High" may be "Extra High".
Nighttime heat purge operation
(Code: [4C])
 No change
 Nighttime [0000]
heat purge
OFF
 Start after [0001]-
the setting [0048]
value x 1
hour(s)
Setting of the linked operation
with external devices
(Code: [4E])
 No change
 ON/OFF [0000]
linked
 ON linked [0001]
 OFF linked [0002]
Changing the ventilation mode
(Code: [EA])
 No change
[0002]
 Heat
exchange
mode
 Automatic [0003]
mode
Compatible with RBC-AMT32E
164-EN