Page 2 • MANUAL DE OPERACIÓN Léalo antes de utilizar este equipo. Thank you for purchasing this Alpine product. Please take a moment to protect your purchase by registering your product now at the following address: www.alpine-usa.com/registration. You will be informed of product and software updates (if applicable), special promotions, news about Alpine.
Page 3 Resistant to Dust and Fresh Water (X409 Only) IP53 rating Resistant to Dust and Fresh Water. Rated IP53 under IEC standard 60529. This product has been tested in a controlled, laboratory environment with an IP (Ingress Protection) rating of IP53 under IEC standard 60529, which is an international standard for measuring the level of protection from dust and fresh water.
Page 4: Table Of Contents
CAUTION ............. 10 Applying Alpine TuneIt App NOTICE ............10 Adjusting the sound via the Smartphone ..27 Features Off-Road Mode (X409 only) Favorite Function ..........12 Turning on Off-Road Mode ......27 About Swiping the Touch Screen ...... 12 Setup Switching the Audio Sources Screen to a Setup Operation ..........
Page 5 Smartphone Apps Setup ........49 About X409/X308U/INE-W987HD ..... 40 Setting Demo mode to Off/On ...... 40 Apple CarPlay (Optional) Off-Road SWRC Settings (X409 only) ..40 Access to Apple CarPlay ........50 Vehicle Setup ............40 Steering wheel Setting ........40 Android Auto (Optional) Installation Setup ..........
Page 6 Tuning to Preset Stations ........52 Disconnecting the Bluetooth Connection ... 63 Changing the connecting Bluetooth Inputting Frequency Directly and Receiving Device ............63 the Radio Station ..........53 SiriusXM Satellite Radio Operation Receiving a Multicast (HD Radio™ Mode (Optional) only) ..............
Page 7 Switching the Image Pattern for the Side Using Voice Recognition function ....80 Camera ............90 Using Siri ............80 Off-Road Camera Operation (X409 only) ..90 Voice Dial Function ........80 Off-Road Rear Camera Operation ....90 Operations During a Conversation ....81 Off-Road Front Camera Operation ....
Page 8 iDataLink Operation Access to iDataLink Mode ......... 94 About Parking Sensor screen ......95 External Accessory Control Operation .... 96 Information Product Software Update ........97 About the Supported Formats ......97 About MP3/WMA/AAC/FLAC ....97 About WAV (Disc) ......... 98 In Case of Difficulty ..........
Page 9: Operating Instructions
If this is the case, pull over in a safe and legal manner • This product may be used in conjunction with the Alpine KAC-001 and location before attempting operation.
Page 10: Warning
USE ONLY IN CARS WITH A 12 VOLT NEGATIVE GROUND. WARNING (Check with your dealer if you are not sure.) Failure to do so may result in fire, etc. • Operation of the system while driving is dangerous. Users should stop vehicle before operating the software. KEEP SMALL OBJECTS SUCH AS SCREWS OUT OF THE REACH OF •...
Page 11: Caution
If you have problems, do not attempt to repair the unit yourself. METAL EDGE. Return it to your Alpine dealer or the nearest Alpine Service Station Route the cables and wiring away from moving parts (like the seat for servicing.
Page 12 Microsoft Corporation in the United States and/or other countries. Alpine accepts no responsibility for lost data, etc., even if data, etc., is • Apple, iPhone, iPod, iPod nano, iPod touch, and Siri are lost while using this product.
Page 13: Features
Features The screen design used in the Owner’s Manual may differ from the actual screen. Favorite Function Frequently used functions can be easily recalled. For details, see “Favorite Function” (page 24). Favorite screen example • Frequently used functions and useful functions can be customized for your convenience. •...
Page 14: Switching The Audio Sources Screen To A Dedicated Screen
Switching the Audio Sources Screen to a Dedicated Screen You can switch the Audio Sources screen to a dedicated screen by touching the icon on one of the three edges of the screen. Shortcut Setup Screen (page 19) Dual Screen (page 14) You can set the Sound Setup or Rear Seat Entertainment You can switch between the displayed screens on System.
Page 15: About Dual Screen
* Touch [ ] to switch to the Navigation menu screen. For details of navigation operations, refer to “Navigation System OM” in the website at http://www.alpine-usa.com. Dual Screen Display Position You can switch the left/right positions of the Audio/Visual screen and Navigation screen.
Page 16: Getting Started
(CAMERA) button (X409 only) Recalls the camera image screen. Controllable with Remote Control This unit can be controlled with an optional Alpine remote control. For details, consult your Alpine dealer. Point the optional remote control transmitter at the remote control sensor.
Page 17: Turning Power On Or Off
RESET switch • The unit is a precision device. Careful handling of the unit should provide you with years of trouble-free operation. For X409 Turning the System On When the system is used for the first time, the language selection menu is displayed. Swipe the Language list screen vertically, then touch your choice from the list of 23 languages.
Page 18: Touch Screen Operation
Touch Screen Operation Switching Sources You can operate the system by using the touch panel on the screen. Press the (AUDIO) button to change the source. • Be sure to touch the onscreen button lightly with the pad of your finger Switching sources using the (AUDIO) button to avoid scratching the display.
Page 19: Operating The Function Button On The Audio/Video Main Screen
Operating the Function Button on the Audio/ About Basic Operation for List Screen Video Main Screen Basic operations on the Setup list screen and the Search list screen. How to display on the list screen differs depending on the selected item. Using the Function button on the Audio/Visual main screen.
Page 20: About The Shortcut Setup Screen
Sound Setup Function About the Shortcut Setup Screen Tone Adjustment mode Displaying the Sound Setup screen, or the Shortcut Setup screen of the Rear Seat Entertainment System screen. Touch the top part of the Audio source screen. BASS ENGINE SQ mode The Sound Setup screen or the Rear Seat Entertainment System Setup Screen is displayed.
Page 21: Rear Seat Entertainment Function
Adjusting Bass Level/Treble Level Rear Seat Entertainment Function Bass Level and Treble Level can be set independently set for Front and Rear speakers by touching [Front] or [Rear]. The Rear Seat Entertainment function independently routes different sources to the front and the rear side of the car. For example, while Setting item: listening to the radio or other audio sources in the front, HDMI can be Bass / Treble...
Page 22: About The Menu Screen
*1 Displays when the Camera Select is set to “Front, ” “Rear, ” or “Other. ” (page 45) *2 Displays when the Bluetooth setting is set to “On. ” (page 29) *3 X409 only *4 Displays the Android Auto screen, displayed when an Android Smartphone installed Android Auto App is connected. (page 50)
Page 23: About The Shortcut Key
You can switch between the 12 hour display and 24 hour display options. For details of the clock display settings, refer to “Navigation System OM” in the website at http://www.alpine-usa.com. Bluetooth devices Name* * When you connect two Hands-Free Phones, the information of the Bluetooth device set to Primary is displayed.
Page 24: How To Input Characters And Numbers (Keypad)
How to Input Characters and Numbers (Keypad) The displayed screens and procedures may vary slightly depending on the function used, but the basic input method is the same. Input screen area. Cursor position alteration switch Cancel Keypad mode finishes. (Delete) Returns to the previous character and erases it.
Page 25: Favorite Function
Favorite Function Editing the Favorite Screen You cannot edit the Favorites screen while driving. Using the Favorite Function Your vehicle must be parked with the ignition key in the ACC or ON position. For details, see “To display the Setup Menu screen” in “Setup Operation”...
Page 26: Registering Items
[Quick Place Search]: Displays the address search keypad. [Help Nearby]: Displays the nearby search screen. [Place Categories]: Displays the selected Place Categories list. • For details of navigation operations, refer to “Navigation System OM” in the website at http://www.alpine-usa.com.
Page 27: Changing The Layout
Touch the icon you want to change from the icon list. When deleting all items Touch [ ] (Delete All). The icon is changed to the selected icon. All items are deleted. Changing the Layout Drag and drop the item to the desired location. The item location is changed.
Page 28: Applying Alpine Tuneit App
• The application program and related specifications and data may be deleted or terminated without notice. • Some Alpine TuneIt App functions may not be available if the Smartphone is not in a service area or receives no signal. Adjusting the sound via the Smartphone [Off-Road] button After setting the above procedure, you can adjust the unit’s sound...
Page 29: Setup
Wireless (Bluetooth) Setup Setup [Wireless] is selected on the Setup main screen in step 3. See “Setup Operation” (page 28). Setup Operation Wireless Setup Menu screen To display the Setup Menu screen: Your vehicle must be parked with the ignition key in the ACC or ON position.
Page 30: Bluetooth Setup
Touch [ ] (Audio), [ ] (Hands-free) or [ ] (Both) Bluetooth Setup of the device you want to connect from the list. Audio: Device is used as an Audio device. [Bluetooth] is selected on the Wireless Setup Menu screen in step 1. See Hands-free: Device is used as a Hands Free Device.
Page 31: Hands-Free Device Primary/Secondary Setting
Enter the passcode that you entered in step 2 again, and Hands-free Device Primary/Secondary Setting then touch [OK]. Make sure the “Bluetooth” setting is “On” ( ). See “Bluetooth Setup” Changing the Character Code of the Phone (page 29). When you connect two Hands-Free Phones, set the priority of the Book operation and the setting of incoming-outgoing calls.
Page 32: General Setup
Screen/Lighting Screen Color (X308U/INE-W987HD only) Illumination Color (X308U/INE-W987HD only) • X409 is designed exclusively for a certain car model. The Initial setting Screen Color (Off-Road on/off ) (X409 only) for sound setup items may differ from the description of Owner’s Manual.
Page 33: Setting The Balance/Fader/Rear Speaker/Subwoofer
Adjusting the Subwoofer Level Setting the Balance/Fader/Rear Speaker/ You can set the Subwoofer level when a Subwoofer is connected. Subwoofer Setting item: Set Balance/Fader/Rear Speaker/Subwoofer/Subwoofer Level/ Subwoofer Level Subwoofer Phase in the Bal./Fad. screen. Setting contents: 0 to 15 (Initial setting: 0) Setting item: •...
Page 34: Equalizer Presets
Adjusting the Frequency Equalizer Presets Touch [ ] or [ ] of “Frequency” to adjust the frequency of the selected band. 10 typical equalizer settings are preset at the factory for a variety of musical source material. Adjustable frequency bands: 20 Hz to 20 kHz (in 1/3 octave steps) Setting item: EQ Presets...
Page 35: Adjusting The Crossover Settings (X-Over)
Adjusting the Crossover Settings (X-Over) Adjusting the Time Correction (TCR) Before performing the following procedures, see “About the Crossover” Before performing the following procedures, see “About Time (page 36). Correction” (page 36). Setting item: Setting item: X-Over Time Correction • When “BASS ENGINE SQ” is selected in the Shortcut Setup, this setting is disabled.
Page 36: Setting The Volume For Each Source
Setting the Volume for Each Source Adjusting the Ring Tone Level You can adjust the receive volume, during the call. Setting item: Source Volume Setup Radio / SiriusXM / Compressed Media* Setting item: 2, 3 iPod Music / AUX* / HDMI* / Bluetooth Audio / Factory Audio* Ring Tone Level Apple Carplay*...
Page 37: About The Crossover
Adjusting to a frequency range speakers. outside that recommended may cause damage to the speakers. For the recommended crossover frequencies of Alpine speakers, refer to the respective Owner’s Manual. We are not responsible for damage or malfunction of speakers caused by...
Page 38: Language Setting
Example 2. Listening Position: All Seats Language Setting Adjust the time correction level of each speaker to almost the same level. The Setup menu, feedback information, etc. for this unit can be changed to appear in the selected language. Sit in the listening position (driver’s seat, etc.) and measure the distance (in meters) between your head and Setting item: the various speakers.
Page 39: Adjusting Brightness
Adjusting Brightness Display/Key Setup Setting item: [Display/Key] is selected on the General Setup Menu screen in step 2. Brightness Setting content: See “General Setup” (page 31). -15 to +15 (Initial setting: 0) You can set up the brightness, color, display, etc., of the screen. You can adjust the brightness between MIN (-15) and MAX (+15).
Page 40: Switching The Display Color
Blue (Initial setting) / Light Blue / Aqua / Red / Green / Amber / Yellow Setting the Display Color (Off-Road on/off) (X409 only) You can select what display color (background image and menu theme) to display for Off-Road on and off modes individually. There are 8 different display colors to choose from.
Page 41: About X409/X308U/Ine-W987Hd
Steering wheel Setting You can view the version information of this product. Make note of this information and refer to it whenever you contact Alpine Tech Support Set this item when an iPhone 5 or later/Android smartphone with or an Alpine-authorized dealer.
Page 42: Source Setup
Source Setup Radio Setup [Source] is selected on the Setup main screen in step 3. See “Setup [Radio] is selected on the Source Setup Menu screen in step 1. See Operation” (page 28). “Source Setup” (page 41). Source Setup Menu screen Setting the TUNER (FM) Tone Quality (Tuner <Setting items>...
Page 43: Siriusxm Setup
Deleting all stored Alert SiriusXM Setup This operation will delete all alerts (artists, songs and teams) stored in [SiriusXM] is selected on the Source Setup Menu screen in step 1. See memory. “Source Setup” (page 41). Setting item: The following operations can be performed to manage the stored Songs, Alert Delete All Artists and Sports Teams information.
Page 44: Setting The Parental Lock
Setting the Parental Lock Signal Strength Information You can lock out channels with passcode protection. Channels that are While listening to a SiriusXM Channel, the Signal strength of the locked cannot be accessed without entering the passcode. You can current channel will be displayed. unlock a channel or change the passcode using this menu option.
Page 45: Switching The Visual Input Signal System
1. See “Source Setup” (page 41). *4 You can select this item only when Camera Select is “Rear. ” *5 Set this setting after closing the Alpine TuneIt App. To use Bluetooth Pandora, set the Bluetooth Pandora setting to “On. ”...
Page 46: Camera Setup
Adjusting the Rear/Front/Side Camera Guide Camera Setup You can adjust the camera guide position. [Camera] is selected on the System Setup Menu screen in step 1. See Setting item: “System Setup” (page 44). Guide Adjustment You can set up items related to the Camera. Touch [Guide Adjustment].
Page 47: Camera Interrupt Setting (Power Off Mode) (Rear Camera Only)
Front Camera screen example When Hitch Guide is set to On <Side Camera> Side Camera screen example Touch [Link]. The 2 vertical guides of the currently-selected guide link together, allowing them to be adjusted simultaneously. Touch [ ], [ ], [ ] or [ ] to adjust the position of the guide.
Page 48: Setting Multi Camera To On/Off
Camera button on the Setting the Default Vehicle Screen Menu screen or press the (CAMERA) button (X409 only). Press and hold the (Favorite) button for at least 2 seconds or touch Setting item:...
Page 49: Rear Seat Entertainment Setup
Rear Seat Entertainment Setup External Accessories Setup [Rear Seat Entertainment] is selected on the System Setup Menu screen [External Accessories] is selected on the System Setup Menu screen in in step 1. See “System Setup” (page 44). step 1. See “System Setup” (page 44). When a Rear monitor equipped with HDMI input is connected to this unit, change this setting to “On.
Page 50: Smartphone Apps Setup
[Smartphone Apps] is selected on the System Setup Menu screen in step 1. See “System Setup” (page 44). Set Alpine TuneIt App to USB (iPhone) when an iPhone is connected, or set to Bluetooth (Android) when an Android Smartphone is paired.
Page 51: Apple Carplay (Optional)
Apple CarPlay Android Auto (Optional) (Optional) Apple CarPlay is a smarter, safer way to use your iPhone in the car. Apple CarPlay takes the things you want to do with your iPhone while What is Android Auto driving and puts them right on the unit. You can get directions, make calls, send and receive messages, and listen to music, all in a way that Android Auto is designed to make it easier to use apps from your phone allows you to stay focused on the road.
Page 52: Radio/Hd Radio™/Rbds
Info area Radio/HD Radio™/ RBDS Station Info. mode: Program Type /Frequency and PS Name/Artist Name/Song RBDS Name/Album Name Radio Text mode: Frequency/ Radio Text The unit can receive HD Radio broadcasting signals based on digital • For details on switching the display of the Radio text, see radio broadcast standards, in addition to analog radio broadcasts using “Displaying Radio Text (RBDS FM Radio mode only)”...
Page 53: Radio Basic Operation
Radio Basic Operation Presetting Stations Manually Tune in a desired radio station you wish to store in the Listening to the Radio preset memory by manual or automatic seek tuning. Touch the Preset number you want to store, for at least Press the (AUDIO) button to select radio mode.
Page 54: Inputting Frequency Directly And Receiving The Radio Station
Inputting Frequency Directly and Receiving the Selecting the Receivable Program Type (RBDS Radio Station FM Radio mode only) You can input a frequency of the same band directly and receive the You can select and receive the currently receivable stations in the radio station.
Page 55: Using Ballgame Mode (Hd Radio™ Mode Only)
Using Ballgame Mode (HD Radio™ Mode only) In live broadcast, such as sportscasts, etc., a time lag occurs between digital sound and analog sound. Therefore, when live broadcasts are received, a time lag between the real broadcast may occur and the unit can change to analog broadcasting automatically.
Page 56: Usb Flash Drive (Optional)
USB Video main screen example USB Flash drive (Optional) You can play back music files (MP3/WMA/AAC/FLAC) and video files (AVI/MKV/MP4) stored in a USB flash drive on the internal player of this system. WARNING It is dangerous for the driver to watch video while driving the vehicle.
Page 57: Fast-Forwarding/Fast-Reversing (Usb Video Only)
Playback Stopping Playback (USB Video only) Touch [ ] during playback. Press the (AUDIO) button to select USB mode. “STOP” indicator is displayed, and playback stops. The display shows the USB mode screen. • Playback starts from the beginning when [ ] is touched while •...
Page 58: Switching Display Modes (During Video File Play Back)
Full Search mode Touch [Audio] or [Video] to switch whether the search list displays music files or video files. Touch your desired Folder name* or File name. When you select a File name, the selected song is played. When you select a Folder name, repeat the same procedure to select another Folder name or File name.
Page 59: Ipod/Iphone (Optional)
Function mode iPod/iPhone (Optional) Artwork display • You can change the artwork position. For details, see “Switching the Artwork Position” (page 39). A separately sold Lightning to USB cable (KCU-471i), etc., is required. Current song no./Total song no. When the unit is connected by the above cable, the controls on the iPod Artist title/Release Date* are disabled.
Page 60: Playback
Quick Search Mode Playback In Quick Search mode, the list from the previous search mode is displayed. For example, if the last time you searched for songs was is in Press the (AUDIO) button to select iPod mode. Albums, the Album list is displayed. If you have not used the search The display shows the iPod mode screen.
Page 61: Alphabet Search Function
Alphabet Search Function Repeat Play The unit is provided with an alphabet search function for effective Touch [ searching. When you use this function in the search mode, you can The Repeat mode select pop up screen is displayed. quickly search an artist or a song, etc. •...
Page 62: Pandora® Music (Optional)
Device” setting of both “Hands-free” and “Bluetooth Audio” to the unit’s Launch the Pandora® on the smartphone. USB port and change the Audio source from Bluetooth Audio, set “Alpine TuneIt App” to “USB (iPhone)” or “Off. ” For more details, see Press the (AUDIO) button to select Pandora® or “Pairing a Bluetooth Device”...
Page 63: Thumbs" Feedback
“Thumbs” Feedback Creating a New Station You can personalize your stations with “Thumbs Up” or “Thumbs Based on the currently playing song or artist, a personalized Pandora Down” feedback, which the system takes into account for future music station can be created. The new station will play more music like it. selections.
Page 64: Connecting A Bluetooth Device (Bluetooth Pandora® Only)
Connecting a Bluetooth Device (Bluetooth Pandora® Only) Registering a Bluetooth device in the unit enables automatic connection. If it does not connect automatically, run through the connection procedure again. Touch [ ] (Phone Setting). The Device Setting select pop up screen is displayed. Touch [Reconnect].
Page 65: Siriusxm Satellite Radio Operation (Optional)
< During Replay mode > SiriusXM Satellite Radio Operation Signal Indicator Indicates the signal strength of SiriusXM. Info area (Optional) Channel Info. Mode*: Channel No/Long Channel Name/Category Name Song Info.Mode: SiriusXM Tuner operation: Artist Name/Song Name/Content Info When an optional SiriusXM Tuner is connected to this unit, the Search mode button following operations may be performed.
Page 66: Receiving Channels With The Siriusxm Tuner
Select the desired channel. Receiving Channels with the SiriusXM Tuner Changing the Display About SiriusXM Satellite Radio Only SiriusXM® brings you more of what you love to listen to, all in one place. Get over 140 channels, including commercial-free music plus the Text information, such as the channel name, artist name/feature, and best sports, news, talk, comedy and entertainment.
Page 67: Smartfavorites Functions
Touch [ ] (TuneScan). SmartFavorites Functions The [ ] (TuneScan) icon is highlighted during TuneScan mode. SmartFavorites allow you to rewind and replay any missed Touch [ ] (TuneScan) during scan playback, programming from your current Band of Preset channels. Miss a music, TuneScan mode will be canceled and the selected track news, talk or sports segment? No Problem, because you can rewind and will be played back normally.
Page 68: Selecting The Channel Directly
Searching by My Music Touch the “Artist Saved” or “Song Saved” to choose to store the Artist or the Song. Touch [My Music]*. Total registrations and Remaining number of registration slots is The artist names and song titles that you have stored and are displayed for 2 seconds, then the Artist or Song is registered as currently playing will be displayed in a list.
Page 69: Replay Function
Replay Function Using Jump Memory and Jump Recall function In SiriusXM mode, you can pause, rewind and replay live Satellite Radio. The Jump Channel is a special channel that you can jump to with the press of a dedicated button and then jump back to the previous channel. Replay mode screen example This channel is often used to select your favorite SiriusXM traffic and weather report channel.
Page 70: Hdmi Device
Touch [ ] or [ ] to select the setting item. HDMI Device Touch [Enter] , then touch [ ], [ ], [ ] or [ ] to change the setting item. Devices supporting HDMI can connect and play back through this unit (for example, an optional DVE-5300 (DVD Player), iPhone or other Touch [ ] to return to the main source screen.
Page 71: Playback
Playback MIX (Random Play) Touch [ ] during playback. Press the (AUDIO) button to select DVD (CD) mode. The tracks (files) on the disc will be played back in a random The display shows the DVD (CD) mode screen. sequence. •...
Page 72: Dvd
Info mode DVD Video main screen example Current track no. Playback control (PBC)/Current audio status Elapsed time Function mode Disc types that can be used for each heading are represented by the following marks. DVD Commercial Video discs (used for the distribution of movies, etc.) or a DVD-R/DVD- RW, DVD+R/DVD+RW recorded in a video mode can be used.
Page 73: Playing A Disc
If a Menu Screen Appears Playing a Disc On DVD mode, menu screens may appear automatically. If this happens, perform the operation described below to start playback. WARNING Direct Menu Operations It is dangerous for the driver to watch the DVD while driving the vehicle.
Page 74: Numeric Keypad Input Operations
Numeric Keypad Input Operations Stopping Playback Touch [Key] again in the menu operation mode. Touch [ ] during playback. The numeric keypad input mode screen appears. “ ” indicator is displayed, and playback stops. Touch a desired number. • Playback starts from the beginning when [ ] is touched while playback is stopped.
Page 75: Forward/Reverse Frame-By-Frame Playback
Forward/Reverse frame-by-frame Playback Searching by Title Number Use this function to easily find positions on the DVD using the DVD’s titles. Perform operations while playback is stopped. In the pause mode, touch [ ] or [ Touch [ ] (Menu Control). The picture advances by one frame each time the button is The menu operation mode screen appears.
Page 76: Switching The Audio Tracks
Switching the Audio Tracks Switching Display Modes DVDs with multiple audio tracks or languages allow switching the While your vehicle is parked, touch [WIDE] to display a sound during playback. popup list of Display Mode. Select the desired mode from the list. Touch [ ] (Audio).
Page 77 • The electronic device must possess an HDMI output interface. • Not all devices with an HDMI output interface can be recognised by this unit. • Use only the Alpine Special HDMI connection cable. Press the (AUDIO) button to select HDMI mode.
Page 78: Bluetooth Operation
Bluetooth compatible device to this unit. The device mobile device or personal computer over short distances. This enables a name of this unit is “X409”, “X308U” or “INE-W987HD” and the hands-free call or data transmission between Bluetooth compatible initial number of the passcode is “0000.
Page 79: Answering A Call
Answering a Call Call Waiting Function Incoming calls are announced by the received call ring tone and a If a call comes in from another phone during a call, a notice is displayed displayed message (PHONE No., etc.). on the screen. This function can only be used if the connected mobile phone has a call waiting function service included.
Page 80: Calling
Second incoming call during a conversation in the Phone Touch the Short Cut icon. Operation screen A contact’s name, phone number, and a confirmation message of the phone number are displayed. • The display or operation may differ depending on the connected mobile phone or the caller’s mobile phone.
Page 81: Using Voice Recognition Function
Entering a Phone Number to Make a Call Speak into the microphone supplied with this unit. • If no speech is detected, the unit may pause depending on version Touch [ ] (Keypad). of the connected iPhone. In that case, touch the microphone icon ] in the center of the Voice Control mode screen.
Page 82: Operations During A Conversation
Adjusting the volume Phone Book Function Adjust the speaker/microphone volume in Voice Dial mode. Perform the same procedure to adjust the speaker/microphone volume of hands- free phone. Phone Book screen example Touch [ ] or [ ]. Adjust the speaker and microphone volumes. Stopping input to the microphone If the surrounding sound (road noise, etc.) is loud, you may wish to cut input to the microphone for 3 seconds.
Page 83: Deleting The Phone Book Entries
Deleting the Phone Book Entries Bluetooth Audio Deleting One Entry from the Phone Book If a Bluetooth compatible mobile phone, portable player, etc. is connected by wireless, you can play back a song (operation is Touch [ ] (Edit). controllable from the unit). Touch the checkbox [ ] of the contact name (or phone •...
Page 84: Playback
Playback Random Play Available for AVRCP Ver. 1.3, 1.4 and 1.5 only. Press the (AUDIO) button to select Bluetooth Audio mode. Touch [ The display shows the Bluetooth Audio mode screen. The Random Play mode select pop up screen is displayed. •...
Page 85: Connecting A Bluetooth Device
Connecting a Bluetooth Device Registering a Bluetooth device in the unit enables automatic connection. If it does not connect automatically, run through the connection procedure again. Touch [ ] (Settings). The Device Setting select pop up screen is displayed. Touch [Reconnect]. Bluetooth connection will start.
Page 86: Auxiliary Device (Optional)
Operating an AUX, AUX DVD or GAME Auxiliary Device Example for AUX, AUX DVD, GAME mode display (Optional) Operating Auxiliary Devices (Optional) To operate devices connected to the AUX terminals of the unit, follow the procedure described below. • Set AUX to “On. ” See “AUX Setup” (page 43). •...
Page 87 Touch the switch to advance to the beginning of the next chapter/track/file. Touch and hold to fast forward. ] (Menu) Calls up the Menu screen. ] (Menu Control)* Calls up the menu operation mode. ] (Folder Down) Switches the program/playlist/folder down. ] (Folder Up) Switches the program/playlist/folder up.
Page 88: Camera Operation (Optional)
). If setting to “Off ” ( ), you cannot display the Rear camera image. For X409, when Off-Road is set to On (page 27), Off-Road Camera can • If you set to Front or Side in “Setting a Default Camera” (page 47), the be displayed.
Page 89: Adjusting The Caution Display Location
Distance guidance mark Adjusting the Caution Display Location The distance guides represent the ground level distance from the rear bumper. It is difficult to accurately estimate the distance to objects above Touch the screen when the image from the camera is ground level.
Page 90: Front Camera Operation
<Situation of the car> Front Camera Operation Actual distances Displaying the Front Camera image from the Menu screen. Press the MENU button. The menu screen is displayed. Error Error The distance guidance mark represents the distance to a flat road surface. Therefore in the case of an upward slope behind the car, the distance guides are displayed closer to the rear bumper than the actual distance.
Page 91: About The Adjustment Of Guide Display On/ Off Setting And Adjustment Of Caution Display Location
Camera View] button once. This requires “Off-Road SWRC” to be • You can perform a Guide Adjustment. For details, see “Adjusting the set to “Camera”. For details, see “Off-Road SWRC Settings (X409 Rear/Front/Side Camera Guide” (page 45). only)” (page 40).
Page 92: Off-Road Front Camera Operation
Corner View you set “Off-Road SWRC Settings” to “Camera”. For details, see “Off-Road SWRC Settings (X409 only)” (page 40). • You can also cycle the camera view by pressing the [Source/ Camera View] button on the steering wheel, only when you set Off-Road Side Camera Operation “Off-Road SWRC Settings”...
Page 93: Changing The Camera Source
• The Rolling angle data is from iDataLink. Changing the Camera Source • For alert value setting, see “Inclinometer Setup (X409 only)” (page 40). The [CAM] button will displayed at the bottom of the camera screen when the Alpine multi-camera selector (KCX-C250MC) is connected.
Page 94 The first two control switches from External Accessory screen* The first two items of information from External Accessory screen are displayed in the lower left and right of the camera screen. For details on External Accessory screen, see “External Accessory Control Operation”...
Page 95: Idatalink Operation
Adjust or confirm the item/information accordingly. iDataLink Operation • Operable functions and displays may differ depending on the vehicle. iDataLink Function Screen example When the unit is connected to the car’s iDataLink module, you can transfer and receive data between the car and the unit to check the car’s Climate screen example status, or to make various operations from the unit.
Page 96: About Parking Sensor Screen
Vehicle Information screen example Parking Sensor Camera interlock screen example (Rear camera) You can check for open doors, check the tire pressure, the battery life, You can check for obstacles through an interlocked camera image by etc. for the vehicle. connecting a Front or Rear Camera.
Page 97: External Accessory Control Operation
When changing the name: External Accessory Control Operation Touch the icon name, then input characters into Edit Name (Keypad). You can also select a basic name from the [Template] of the Keypad. For details on how to input characters using the You can set the headlights to ON/OFF or adjust the air suspension from keypad, see “How to Input Characters and Numbers (Keypad)”...
Page 98: Information
About the software license of the product Supported playback sampling rates and bit rates The software installed in the product contains open-source software. See the following Alpine website for details on the open source software. MP3 (USB Flash drive/Disc) Sampling rates: 48 kHz, 44.1 kHz, 32 kHz, 24 kHz, 22.05 kHz, 16 kHz,...
Page 99: About Wav (Disc)
Corresponding File Systems Terminology This device supports FAT 16/32. Bit rate The maximum nested folder depth is 8 (including the root This is the “sound” compression rate specified for encoding. The higher directory). File names are limited to 256 characters (including the the bit rate, the higher the sound quality, but also the larger the files.
Page 100: In Case Of Difficulty
• If the area you are in is a primary signal area, the antenna may properly connected, or then consult your authorized not be grounded and connected properly. Alpine dealer. - Check your antenna connections; make sure the antenna is properly grounded at its mounting location.
Page 101: If This Message Appears
Bluetooth If this Message Appears Please connect a Bluetooth audio device. • The Bluetooth audio device was not connected correctly. Various messages are displayed on the screen during operation. In - Check the settings for the unit and the Bluetooth audio device addition to the messages telling you the current status or providing and reconnect.
Page 102 - When “External Audio Processor” (page 48) is set to “On, ” you or otherwise damaged. Replace the antenna if necessary. cannot perform Sound Tuning from the Alpine TuneIt App. Set - SiriusXM products are available at your local car audio retailer “External Audio Processor”...
Page 103: Specifications
Output Power +4 dBm Ave. (Power class 2) MONITOR SECTION Profile HFP (Hands-Free Profile) OPP (Object Push Profile) Screen Size 9” (X409) PBAP (Phone Book Access Profile) 8” (X308U) A2DP (Advanced Audio 7” (INE-W987HD) Distribution Profile) LCD Type Transparent type TN LCD...
Page 104: End User License Agreement (Here)
System. The right to use the System shall expire either when the user destroys this software, or when any of the terms for use is violated and Alpine, INE-W987HD Space Machine and/or HERE exercise the option to revoke the license to use this software.
Page 105: Limited Warranty
ALPINE ELECTRONICS OF AMERICA, INC. (“Alpine”), is dedicated to quality craftsmanship and is pleased to offer this Warranty. We suggest that you read it thoroughly. Should you have any questions, please contact your Dealer or contact Alpine at one of the telephone numbers listed below.
Page 106 N’oubliez pas de consacrer un moment à la protection de votre achat en enregistrant votre produit dès maintenant à l’adresse suivante : www.alpine-usa.com/registration. Recuerde que con solo unos pocos pasos podrá proteger su producto, registrándolo a través de la siguiente...
Page 107 ˜ Before you use this product, be sure to carefully read this installation manual and the separate user's manual so that you can use the product correctly. Alpine Electronics bears no responsibility for problems that arise as a result of failure to follow the instructions in the manuals.
Page 108 The installation and wiring of this product re- wheel, gear shift, or the like; or pose a threat quires specialized skills and experience. Have to passengers. Doing so could lead to an ac- the product installed by an Alpine authorized cident or injury. dealer.
Page 109 Jeep Wrangler X409-WRA-JL 20200825v1 ˜ 3/29 Tools Required 10mm Socket 8mm Socket 7mm Socket Wire Cutters Extension Ratchet #2 Phillips Screwdriver Torx T20 Torx T47 Panel Removal Tools Wire Fishing Tool Cordless Power Drill Digital Multimeter...
Page 110 Jeep Wrangler X409-WRA-JL 20200825v1 ˜ 4/29 Accessory List Display Bezel Maestro Module Main Harness Power Inverter Bracket Display Bracket Tuner Bracket External Bluetooth Mic USB Power Adapter USB, HDMI, Aux Interface Aux/Preout Harness Documents Chime Speaker Quick Reference Alpine Guide...
Page 111 Camera Module FACTORY CAMERA BSV INTERFACE SGS-BSV1-WJL Power & CAN Can1 VIDEO OUT Can2 X409 Display Unit X409 Source Unit Key Harness Camera Male To Male RCA Direct Camera Adapter Source Unit HDMI Bracket Coupler Mini USB To USB For Center...
Page 112 Jeep Wrangler X409-WRA-JL 20200825v1 ˜ 6/29 Programming The iDatalink Maestro Module INSTALL THE WEBLINK PLUG-IN REGISTER A WEBLINK ACCOUNT Go to: Go to: idatalinkmaestro.com/plugin and follow the installation steps. The idatalinkmaestro.com/register and complete the registration process. Maestro module must be programmed specifically for each vehicle A confirmation email will be sent to you requiring validation.
Page 113 If your vehicle does not have those then you will not need to use those. If you are installing the X409-WRA-JL in a Gladiator JT then a few of the steps will vary slightly so please take notice to this as you go through the installation.
Page 114 Jeep Wrangler X409-WRA-JL 20200825v1 ˜ 8/29 Factory Unit Disassembly Process As a precautionary measure it’s a good idea to Unsnap the 6 clips and remove the knee panel mask out the dashboard and panels to prevent under the steering wheel using a panel removal scratches.
Page 115 Jeep Wrangler X409-WRA-JL 20200825v1 ˜ 9/29 Factory Unit Disassembly Process (Continued) Unsnap 6 clips and remove radio bezel using a Unsnap the 6 clips and remove the knee panel panel removal tool. under the steering wheel using a panel removal tool.
Page 116 Remove the (4) 10mm screws to remove holding it in place. Once the installation of the the bracket. Then remove the (2) 8mm screws lower X409-WRA-JL tuner is completed the vent can go and the (2) 10mm screws top to remove the module. back in place.
Page 117 Jeep Wrangler X409-WRA-JL 20200825v1 ˜ 11/29 Factory Unit Disassembly Process (Continued) Loosen the clips around the top panel visor area. Remove panel above drivers door going to the B pillar. Unclip 7 clips and remove the center media stack.
Page 118 Jeep Wrangler X409-WRA-JL 20200825v1 ˜ 12/29 Installation Instructions Run the GPS antenna Bluetooth microphone Mount the microphone next to the rear view mirror cables up the A pillar along the OEM wiring. Route and run the cable behind the factory panels. Route as shown on the diagram on page 17.
Page 119 Jeep Wrangler X409-WRA-JL 20200825v1 ˜ 13/29 Installation Instructions (Continued) If you are using the optional SiriusXM tuner, Cable For vehicles with heated seats or the power tie the module on top of the source unit. inverter attach the Power Inverter bracket using the supplied (2) M5X10LMM screws and lock washers.
Page 120 Gladiator JT. If the vehicle has the heated seat module clip that Use (4) OEM bolts to secure the X409 source into the bottom bracket. The OEM clips on the unit tuner bracket to the vehicle. If the vehicle is module will snap into the bracket.
Page 121 Jeep Wrangler X409-WRA-JL 20200825v1 ˜ 15/29 Installation Instructions (Continued) At radio cavity, connect the main harness, white If the vehicle has an OEM amplifier the KCX- FM adapter, and green SiriusXM antenna, and F200INT will need to be purchased separately.
Page 122 Jeep Wrangler X409-WRA-JL 20200825v1 ˜ 16/29 Installation Instructions (Continued) Insert the X409 USB HDMI box into the OEM Plug in the OEM USB and the USB from the box Center Media panel. to the power adapter. The adaptor needs to be plugged into the BLACK micro usb.
Page 123 MENU START ENGINE STOP MEDIA X409-WRA-JL Source Unit GPS Antenna Installation IMPORTANT: Follow the GPS antenna installation procedure shown below. Failure to do so will result in poor GPS performance for CarPlay, Android Auto, and off-road navigation. Route from behind...
Page 124 Jeep Wrangler X409-WRA-JL 20200825v1 ˜ 18/29 X409-WRA-JL Wiring Diagram X409D - Display Brown DVD Remote Brown Mon Remote Brown/White Remote In Brown Remote Out Red/White DVD Status In AUX Input X409 DISP. OUT CAN I/F HDMI IN HDMI OUT SXM/DAB PRE OUT EXT.
Page 125 Jeep Wrangler X409-WRA-JL 20200825v1 ˜ 19/29 X409-WRA-JL Wiring Diagram Continued To Vehicle Connectors Power Antenna Antenna AMPLIFIED VEHICLES Speaker (Green) (White) 52-pin Connector WARNING! Reset Button Black Used Used 10-Pin Chime 18-Pin iDatalink MAESTRO Module Only 2 connections are necessary for the OEM ampli ed system.
Page 126 Jeep Wrangler X409-WRA-JL 20200825v1 ˜ 20/29 Connection Of An External Amplifier RCA Extension Cable (sold separately) Remote Turn-On Lead (Blue/White) CAN I/F HDMI IN HDMI OUT Subwoofer RCA Connectors SXM/DAB Front Output RCA Connectors PRE OUT W.REMOTE POWER Rear Output RCA Connectors...
Page 127 Do not use the head unit’s USB to power HDMI devices. This port is meant for Apple CarPlay, Android Auto, and USB ash drives. X409-WRA-JL Source Unit For all phones the USB CAN I/F power source needs to be a 2A source. This will...
Page 128 Jeep Wrangler X409-WRA-JL 20200825v1 ˜ 22/29 X409-WRA-JL Wiring Diagram To SiriusXM Tuner Vehicle Antenna GPS Antenna (Included) SPEED SENSOR To the vehicle speed pulse line (Green/White) CAMERA To Front, Rear or Side camera IDATALINK I/F To iDataLink module AUX INPUT...
Page 129 Jeep Wrangler X409-WRA-JL 20200825v1 ˜ 23/29 Wire Harness Pin Outs Remote Harness Radio Main Cam Aux Data Yellow 22AWG Blue 22AWG Red 22AWG Yellow 22AWG Red 20AWG Black 22AWG Blue 22AWG Black 22AWG Blue/White 22AWG Black 22AWG Brown 22AWG White 22AWG...
Page 130 3 - Front Camera 4 - Side Camera Power & CAN Can1 VIDEO OUT Can2 Not Used Alpine Direct Front Camera Alpine Direct Front Camera Direct Camera Adapter Video Output Connector Accessory (Red) Ground (Black) Direct Camera CAN I/F Connector...
Page 131 Jeep Wrangler X409-WRA-JL 20200825v1 ˜ 25/29 Connection Of KAC-001 (Sold Separately) KAC-001 Side View POWER RESET HEADUNIT OUTPUT UPDATE Reset USB port Button (Firmware updates only) Output 1 (Purple) BATT* (Yellow) Output 2 (White/Red) ACC (Red) Output 3 (Brown) GND (Black)
Page 132 Jeep Wrangler X409-WRA-JL 20200825v1 ˜ 26/29 Steering Wheel Configuration Off Hook Voice On Hook Volume Up Source Seek Up Volume Down Preset Up Seek Down Button Press Once Press And Hold Seek Up Track + None Seek Down Track -...
Page 133 Jeep Wrangler X409-WRA-JL 20200825v1 ˜ 27/29 Setting Up OEM Aux Switches Once in the setup menu (see page 28) select SYSTEM and then MAESTRO MODULE. Select VEHICLE FEATURES. Select AUX SWITCHES. Select the switch that you would like to edit (AUX 1, AUX 2, AUX 3, or AUX 4).
Page 134 Set Up Guide Turn the vehicle’s Ignition switch to ACC. Turn ON the X409-WRA-JL by pressing any key. Select the user language and press OK. To get into the settings the parking brake sequence needs to be done. Engage the parking brake, release the parking brake, and engage the parking brake again.
Page 135 Jeep Wrangler X409-WRA-JL 20200825v1 ˜ 29/29 Troubleshooting Guide Continued Symptom Possible Cause Remedy Maestro module is flashed for No output from RCA’s Re-flash module for non-amplified system. amplified system. With vehicle in (P)PARK engage the parking Cannot enter SETTINGS Vehicle is in motion or parking brake.
Page 163 User Manual Alpine Navigation System Navigation software for the Alpine Navigation System English January 2019, Ver. 3.0...
Page 164 Table of contents 1 Warnings and safety information ................... 5 2 Getting started ........................6 2.1 Initial set-up ..........................6 2.2 Screen controls ........................8 2.2.1 Using the buttons and other controls ....................8 2.2.2 Using the cursor ..........................9 2.2.3 Using the keyboard ..........................
Page 165 3.1.7 Selecting a location on the map ..................... 41 3.1.8 Planning a Multipoint Route ......................42 3.2 Checking Route Information and Alternatives ............... 43 3.3 Checking Traffic Events ......................44 3.4 Editing the route ........................46 3.4.1 Setting a new starting point ......................47 3.4.2 Adding an additional destination ....................
Page 166 4.2 Information menu ........................68 4.2.1 Where Am I ........................... 70 4.2.2 Trip Monitor ..........................70 4.3 Setup menu ..........................71 4.3.1 Route preferences .......................... 72 4.3.1.1 Vehicle profile ............................73 4.3.1.2 Route Planning Method types......................... 74 4.3.1.3 Road types .............................. 74 4.3.2 Sound ............................
Page 167: Warnings And Safety Information
Plan the route before your departure and stop if you need to change the route. You must follow the traffic rules. If you deviate from the planned route, Alpine Navigation System changes the instructions accordingly.
Page 168: Getting Started
2 Getting started Alpine Navigation System is optimized for in-car use. You can use it easily by tapping the screen buttons and the map with your fingertips. Easy map updates Update your maps regularly as road networks are continuously evolving all over the world. About 15% of the roads are changed each year, new ones are built, directions are altered, new speed limits are set, and many other changes are made.
Page 169 Read the end-user license agreement, and tap if you agree with the terms of use. The Configuration W izard starts. Tap to continue. Select the language and speaker used for voice guidance messages. Later you can change it in Regional settings (page 75). Tap to continue.
Page 170: Screen Controls
You need to confirm selections or changes only if the application needs to be restarted, if it needs to perform a major reconfiguration, or if you are about to lose some of your data or settings. Otherwise, Alpine Navigation System saves your selections and applies the new settings without confirmation as soon as you use the controls.
Page 171: Using The Cursor
2.2.2 Using the cursor You can select a map location by tapping the map during navigation. When a map location is selected, the cursor ) appears at the selected point on the map. The location of the cursor can be used as the destination of the route or a new Alert Point. You can also search for Places around it or add this location to your saved locations.
Page 172: Using Touch Gestures
2.2.4 Using touch gestures You usually need to tap the screen only once. However, some useful features can be accessed with other gestures. See the table below. Action Function Tapping and Tap and keep pressing the following buttons to reach extra functions: holding the screen Tap and hold the following button on list and menu screens to show the...
Page 173 Zooming in and Change how much of the map is displayed on the screen. Alpine Navigation System uses maps that let you examine the locations at various zoom levels, always with optimized content. It always displays street names and other text with the same font size, never upside-down, and you only see the streets and objects that you need.
Page 175: Navigation View
2.3 Navigation view The navigation view is the main screen of Alpine Navigation System that shows the planned route on a map. Alpine Navigation System works with digital maps which are not simply the computerized versions of traditional paper maps. Similarly to paper road maps, the 2D mode of digital maps shows you streets and roads.
Page 176 North. Traffic It shows traffic-related information. See page 44. Zoom You can change how much of the map is displayed on the screen. Alpine Navigation System uses maps that let you zoom in and out on the map. Page Lane On multi-lane roads, it shows the lanes ahead and their directions.
Page 177: Streets And Roads
When entering a tunnel, the map is replaced with a generic tunnel image. See page 18. 2.3.1 Streets and roads Alpine Navigation System shows the streets similarly to paper road maps. Their width and colors correspond to their importance; you can easily tell a freeway from a small street.
Page 178: The Planned Route
2.3.3 The planned route The planned route is the currently navigated route. Whenever the destination is set, the route is active until you delete it, reach your destination or suspend navigation. Alpine Navigation System displays the route in the following ways:...
Page 179: Maneuver Icons
A smaller icon shows the type of the second next maneuver if it is near the first one. Otherwise, only the next maneuver is displayed. 2.3.5 Maneuver icons During navigation the next maneuver is displayed in the top left corner. Most of the maneuver icons are intuitive.
Page 180: Lane Information And Signposts
When navigating on multi-lane roads, it is important to take the appropriate lane in order to follow the planned route. If lane information is available in the map data, Alpine Navigation System displays the lanes and their directions using small arrows at the bottom of the map. Highlighted arrows represent the lanes and the direction you need to take.
Page 181 The top-down overview of the tunnel displayed in a separate window helps you orient yourself. The remaining distance in the tunnel is also displayed. After leaving the tunnel, the original map view returns. Tunnel view can be turned off in .
Page 182: Freeway Services
Type Description 3D terrain Alpine Navigation System displays 3D hills and mountains in the Navigation view, and illustrates them by coloring and shading on the 2D map. Elevated roads Elevated roads are complex intersections and vertically isolated roads (such as overpasses or bridges) displayed in 3D.
Page 183: Traffic Events
2.3.11 Traffic events Road segments affected by traffic events are displayed in a different color on the map. The following icons may appear at the top right corner of the screen: Button Description It is displayed when traffic events are not received. It is displayed when traffic events are received but they do not affect the planned route.
Page 184 You can see the following menu options when you are navigating without a planned route: Button Function Select your destination by entering an address or its coordinate, or by selecting a Place, a Saved Location, or a Saved Route. You can also look up your recent destinations from the History.
Page 185 Tap the Back button to return to the previous screen. You can also press and hold this button to quickly return to the Navigation view from any other screen.
Page 186: Using The Navigation
3 Using the navigation By default, Alpine Navigation System calculates routes using the road network of the maps provided with the product. You can select the destination and start navigating to it right away (normal navigation) if you need a route for immediate navigation.
Page 187 . You can see the input field at the top of the screen. Right next to it you can see the search area, the town around which the search is carried out. The default search area is the area where you are located. For a local search, skip the next step. (optional) To search in a different area, tap the input field with the search area, and start entering the name of the new search area on the keyboard.
Page 188: Selecting An Address
• to see the list of matching addresses. • to see the list of matching Place category names. Scroll the list and select one of the categories. You get the list of Places in that category ordered by their distance from your current position. •...
Page 189: Entering An Address
Press the navigation hardkey button to access the Navigation menu. Select the country by performing the following steps: By default, the Alpine Navigation System proposes the country where you are or in case there is no valid GPS position, the country of the last known position. If needed, tap Start entering the first few letters of the country.
Page 190: Selecting A Town Center
To open the list, tap , and select the town or ZIP code. Enter the street name and the house number or crossing street by performing the following steps: Start entering the street name on the keyboard. The names that match the string appear in a list.
Page 191: Selecting The Midpoint Of A Street
Press the navigation hardkey button to access the Navigation menu. Go to and modify the country as described earlier (page 27), if necessary. Select a new town or ZIP code by performing the following steps: and start entering the first few letters of the town or the first few numbers of the ZIP code.
Page 192: Using The Zip Code To Select A Destination
Go to and select the country and town as described earlier. Start entering the street name on the keyboard. The names that match the string appear in a list. to open the list of results. Select the street from the list. Start entering the name of the crossing street (tap to enter letters), or tap to open the list of results.
Page 193: Selecting A Place Of Interest
Continue the search as described previously (page 27). 3.1.3 Selecting a Place of Interest You can search for Places of Interest (Places) in the menu. Using the same screen, you can find a Place by selecting one of the following options: •...
Page 194: Using Quick Search Categories
3.1.3.1 Using Quick search categories The Quick search feature helps you quickly find the most frequently selected types of Places. Perform the following steps: Press the navigation hardkey button to access the Navigation menu. The following Quick search categories appear: •...
Page 195: Searching By Category
(optional) If needed, tap to further filter the list of results. Browse the list and tap one of the list items. The route is calculated and the map appears showing the entire route, where you can check route information and route alternatives. Tap to modify the route parameters, or tap to start your journey.
Page 196 • to search for a place within a selected town. (The result list is ordered by the distance from the center of the selected town.) (optional) If you have selected , select the town to search in. Select one of the main Place categories (for example, Accommodation), then browse the subcategories (for example, Hotel or Motel) to find your destination.
Page 197: Searching By Name
To filter the list of results by providers, tap and then the provider logo on the right side of the screen. Browse the list and tap one of the list items. A full screen map appears with the selected point in the middle.
Page 198 (optional) If you have selected , select the town to search in. You can search for the name of a Place in all categories by performing the following steps: . Using the keyboard, start entering the name of the Place or browse in the categories.
Page 199: Finding Help Nearby
3.1.3.4 Finding help nearby To quickly search for nearby assistance, perform the following steps: Press the navigation hardkey button to access the Navigation menu. Places in the following pre-set search categories can be searched for around the current position (or around the last known position if the current position is not available): •...
Page 200: Selecting A Saved Location
3.1.4 Selecting a Saved Location To select a location that you have already saved (page 53), perform the following steps: Press the navigation hardkey button to access the Navigation menu. The list of Saved Locations is displayed. It contains two pre-set categories: Home and Work. Tap the location that you want to set as your destination.
Page 201: Selecting A History Item
3.1.5 Selecting a History item The destinations that you have used earlier appear in the History list. Smart History offers these locations from your previous destinations, using parameters like the current time of day, the day of week, and the current location. The more you use the navigation software, the better it can guess your desired destination.
Page 202: Entering Coordinates
3.1.6 Entering coordinates To select a destination by entering its coordinates, perform the following steps: Press the navigation hardkey button to access the Navigation menu. You can enter the latitude and longitude values in any of the following formats: decimal degrees, degrees and decimal minutes, or degrees, minutes and decimal seconds.
Page 203: Selecting A Location On The Map
3.1.7 Selecting a location on the map To select a map location, perform the following steps: Locate your destination on the map. Move and scale the map as necessary. Tap the location that you want to select as your destination. The cursor ) appears there.
Page 204: Planning A Multipoint Route
3.1.8 Planning a Multipoint Route To build your route destination-by-destination, perform the following steps: Press the navigation hardkey button to access the Navigation menu. There is only one line in the list of route points, the starting point of the route, which is normally the current GPS position.
Page 205: Checking Route Information And Alternatives
When you have added all the route points, tap and the planned route is automatically calculated. 3.2 Checking Route Information and Alternatives To get a map overview of the planned route and check different parameters of the planned route, perform the following steps: Press the navigation hardkey button to access the Navigation menu.
Page 206: Checking Traffic Events
• to list route alternatives and select the most suitable route for you. on the Route Summary screen to carry out additional actions, for example edit your route preferences or display the itinerary. 3.3 Checking Traffic Events Offline statistical traffic information (historical speed information or traffic patterns) can be taken into account in the route calculation based on the time of day and the day of week if suitable data can be found on the device.
Page 207 If there is at least one significant event on the planned route, a description is displayed about the next event. Tap to see the list of all events. Tap any of the list items to see its details and to display the affected road segment in its full length on the map.
Page 208: Editing The Route
to display historical traffic information. A 2D map is displayed with road segments colored by the likely density of the traffic in the given period. The information relevant for the current period is shown when you open the screen. If necessary, you can browse the map for a better view of certain road segments.
Page 209: Setting A New Starting Point
3.4.1 Setting a new starting point For normal navigation, all routes are calculated from the current position. You can pause navigation to check future routes, simulate them or see their length in time and distance. Then you can set the starting point of the route to a location other than the current GPS position.
Page 210: Adding An Additional Destination
to continue. The map returns with a transparent position marker (showing that there is no GPS reception). If a planned route already exists, it is now recalculated starting from the selected location. To return to normal navigation, tap 3.4.2 Adding an additional destination If you already have a planned route and you select a new destination as described in the above sections, the route to the previous destination is deleted and a new route is calculated.
Page 211: Modifying The List Of Destinations
3.4.3 Modifying the list of destinations To edit your route, perform the following steps: Press the navigation hardkey button to access the Navigation menu. In the Navigation menu, tap You have the following options on this screen: • to delete all the destinations, or optimize the waypoints or the route.
Page 212: Deleting The Planned Route
Type in a name and tap The route is saved and it is available in in the Navigation menu. By selecting a previously saved route, Alpine Navigation System recalculates the route using the saved destination and/or the waypoints. 3.4.5 Deleting the planned route You have the following two options to delete the navigated route: •...
Page 213: Selecting A Route Alternative When Planning The Route
Select one of the route alternatives and tap to return to the previous screen. Alpine Navigation System recalculates the route. Tap to start your journey. The orange line now shows the new planned route.
Page 214: Selecting A Route Alternative For An Existing Route
Select one of the route alternatives and tap to return to the previous screen. Alpine Navigation System replaces the original route. Tap to start your journey. The orange line now shows the new planned route.
Page 215: Saving A Location
3.5 Saving a location To add any location to the saved locations (the list of frequently used destinations), perform the following steps: Select a destination as described before. It can be an address, a Place, any location on the map, a previously used destination from History, and so on. When the map appears with the route, tap (optional) Using the keyboard, you can change the name offered for the Saved Location.
Page 216: Editing A Saved Location
3.5.1 Editing a Saved Location To edit a location that you have already added as a Saved Location, perform the following steps: Press the navigation hardkey button, and tap The list of Saved Locations is displayed. Tap the location you want to edit, tap and enter the name of the location on the keyboard, then tap In Saved Locations, Home and Work cannot be renamed.
Page 217 The warning for road safety cameras is disabled when you are in a country where road safety camera warning is prohibited. However, you must make sure that using this Note! feature is legal in the country where you intend to use it. Return to the Navigation view, and select the Alert Point.
Page 218: Running A Simulation
3.7 Running a Simulation To run a simulated navigation that demonstrates the planned route, perform the following steps: Press the navigation hardkey button to access the Navigation menu. In the Navigation menu, tap . The simulation starts from the starting point of the route and leads you through the whole planned route using a realistic speed.
Page 219: Off-Road Mode
3.8 Off-Road Mode When first started, Alpine Navigation System calculates routes using the map road network provided with the product. If you want to disregard roads during navigation, you can switch to Off-Road mode, for example when driving in a desert.
Page 220: Off-Road Menu
Record [Stop] To stop the recording, press the [Map] button then [Record] button on map. After recording is stopped you can assign a name and track difficulty to the recording. Record [Pause] Recording can be paused and resumed at any time by pressing the [Pause] button on the map.
Page 221: Import/Export Recorded Tracks
Tracked ride You can find all previously recorded tracks by going to [Nav] > Menu > Off-Road > Tracked Ride. You can then also import and export tracks and select a track for track-follow Off-Road POI You can access Off-Road specific POI from the trailhead and Off-Road area category by going to [NAV] >...
Page 222: Selecting The Destination In Off-Road Mode
3.8.5 Selecting the destination in Off-Road mode You can select a destination (waypoint or final destination). The key difference between Off-Road mode and On-Road mode is that in Off-Road mode the vehicle position and the destination are linked by a straight line disregarding the road network and traffic regulations. To select a start or end point of a previously recorded track go the Off-Road tab in the main menu, select the tracked ride option and then choose your track.
Page 223: Saved Location
To update your navigation software and its maps, perform the following steps: Download and install the Toolbox PC tool on your PC. Go to the alpine.naviextras.com website. If you do not have a user account yet, create one. Click Download PC tool on the right side of the page to access the download page.
Page 224 Use the Toolbox PC tool to download updates and to purchase additional extras at your convenience. For instructions on using the Toolbox, see the Toolbox How-to Guides at alpine.naviextras.com/shop/portal/support. Once the download is complete, remove the USB storage device from the PC.
Page 225: Reference Guide
There is a special proximity warning for road safety cameras (like speed or red light cameras) and other proximity Alert Points (like schools or railroad crossings). These Alert Points are not part of Alpine Navigation System. You can download Alert points from alpine.naviextras.com or you can upload points in a specific text file if needed.
Page 226: Route Calculation And Recalculation
As a result, Alpine Navigation System may suggest a different route during the weekday rush hours, especially in major cities with frequent traffic jams. See page 4.1.5 Smart Zoom...
Page 227: Speed Limit Warning
The maximum speed set in the vehicle profile (page 73) is also used for this warning. Alpine Navigation System alerts you if you exceed the pre-set value even if the legal speed limit is higher.
Page 228: Intelligent Navigation
The following sections describe these features. 4.1.9.1 Congestion detour on highways Alpine Navigation System may offer a detour when you slow down on a highway due to a traffic jam. The Potential congestion detour window appears and shows the length and duration of the detour.
Page 229: Real-Time Alternative Routes
You can accept the recommended detour by tapping 4.1.9.2 Real-time alternative routes Alpine Navigation System may offer an alternative route on normal roads in case of a traffic jam. The possible alternative route window appears and shows the length and duration of the detour.
Page 230: Hints Upon Detour
Alpine Navigation System is searching for parking places in the Places of Interest. 4.1.9.4 Hints upon detour If you leave the planned route by exiting a freeway, Alpine Navigation System tries to guess the reason for making a detour. The Reason for detour window appears and shows available gas stations, restaurants or other Places around the current position.
Page 231 Shows the GPS Information screen with satellite position and signal strength information. Shows the version of Alpine Navigation System, licenses, content, demo routes, credits, statistics, and the SWID.
Page 232: Where Am I
4.2.1 Where Am I This screen contains information about the current position (or about the last known position if GPS reception is not available). You can access it the following two ways: • By going to the Navigation menu and tapping •...
Page 233: Setup Menu
4.3 Setup menu You can configure the navigation settings, and modify the behavior of Alpine Navigation System, by pressing the navigation hardkey button, and tapping Tap the arrows to view the content of other pages.
Page 234: Route Preferences
Adjust the different sound volumes. Enable and set up warnings for speed limit, Alert Points (such as speed cameras), and road signs. Fine-tune the appearance of the Navigation view or adjust how the software helps you navigate with different kinds of route-related information on the Navigation view. Change the voice guidance language, set the time zone, the measurement units, the time and date, and formats, and customize the application for your local language.
Page 235: Vehicle Profile
4.3.1.1 Vehicle profile You can select the following vehicle types: Button Description Maneuver restrictions and directional constraints are taken into account when planning a route. Roads are used only if access for cars is allowed. Private roads and resident-only roads are used only if they are inevitable to reach the destination.
Page 236: Route Planning Method Types
Usually, the best selection for fast and normal cars. Results in a route with fewer turns and no difficult maneuvers. W ith this option, you can make Alpine Navigation System take, for example, the freeway instead of a series of smaller roads or streets.
Page 237 Per-use toll roads are pay roads where there is a per-use charge in the routes by default. If you disable toll roads, Alpine Navigation System plans the best toll- free route. Alpine Navigation System includes ferries in a planned route by default.
Page 239: Sound
4.3.2 Sound You have the following options for each sound type: Button Function Disable verbal instructions. This function is enabled by default. Choose from the following options: Announce the street names in the native language area of the selected voice guidance language. Announce the road numbers only.
Page 240: Warnings
You can enable and modify the following settings: Button Description Alpine Navigation System is able to warn you if you exceed the current speed limit. This information may not be available in your region, or may not be fully correct for all roads on the map.
Page 241: Navigation View
Maps may contain driver alert information that can be shown on the Navigation view in a similar way as real-life road signs. Tap it to enable or disable the warning for these road segments (for example, dangers and sharp curves). For each category of warning signs, set the warning type (visual or audio and visual) and the distance from the hazard to receive the warning at.
Page 242 You can modify the following settings: Button Function Adjust the basic zoom and tilt levels to your needs. Three levels are available. Switch between daytime and night color modes or let the software switch between the two modes automatically a few minutes before sunrise and a few minutes after sunset.
Page 243: Regional
A top-down overview of the tunnel and the remaining distance are also displayed. In certain situations, Alpine Navigation System offers a detour when there is a traffic jam on a highway. See page 66.
Page 244: Traffic
(not counting the traffic jam). If you set the Offer detour feature to 10 minutes, Alpine Navigation System recalculates the route because it saves 15 minutes, which is more than the 10 minutes you set. If you set it to 20 minutes, the original route is kept because the detour would save you only 15 minutes.
Page 245: User Profiles
4.3.7 User Profiles If more drivers use Alpine Navigation Systemfor navigating, their settings can be remembered by using one of the user profiles. You can create a new profile by tapping enter a name, and select a car model. If you select a new profile, the application restarts so that the new settings can take effect.
Page 246: End-User License Agreement
5 End-user license agreement 1. Definitions The following terms shall have the meaning defined hereunder in this agreement when used with capital letters. The text of this agreement may also contain further defined terms. “Agreement” means this End User Licence Agreement (EULA) containing the terms and conditions of use of the Software, Databases and Services by You as the end user.
Page 247 3.1 This Agreement will be governed by the laws of the country where the Licensor has its statutory seat or in the absence of such incorporation where it has its central administration (“country of residence”) without regard to such country’s choice of law provisions. 3.2 The courts of the country of residence specified in Section 3.1.
Page 248 5.4 Services available through the Software may transmit various types of information or content to the User, which information or content is gathered and provided by third party service providers. Therefore it is understood and accepted that neither the Licensor nor the Software Owner has the ability or right to control, alter or modify such information and content and the Service itself is only a function enabling the Software to access, download and display information and content to the User.
Page 249 THE DATABASE OWNERS, THE SOFTWARE OWNER, THE SERVICE PROVIDERS AND THIRD PARTY SUPPLIERS EXPRESSLY DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO, THE IMPLIED W ARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY, SATISFACTORY QUALITY, ACCURACY, TITLE AND FITNESS FOR A PARTICULAR PURPOSE.
Page 250 through the Services provided by third parties may only be used at the risk of the User and for the benefit of the User. User acknowledges that the Databases are the confidential information of Database Owners and disclosure of the Databases to third parties is prohibited. 8.9 USE OF THE NAVIGATION PRODUCT’S REAL TIME ROUTE GUIDANCE FUNCTION IS AT USER’S SOLE RISK AS LOCATION DATA MAY NOT BE ACCURATE.
Page 251 11.3 Online information and content are downloaded by the Navigation Product from the Software Owner’s or other suppliers’ online content servers. The Licensor hereby excludes any liability of its own for all information and content. As no control may be exercised by the Licensor or the Software Owner over the information or content, neither Licensor nor Software Owner warrants the legality, quality, suitability, accuracy, fitness for a specific purpose or territorial coverage of the information and content, furthermore no warranty is offered regarding the availability (e.g.
Page 252 12.1 Third parties supply Services or Database built into the Navigation Product and such third party suppliers may have special terms and conditions of use (“Supplier Terms”), and You as the User accept those terms together with this Agreement. 12.2 Potential third party suppliers (and their Supplier Terms) may have their Database or Service distributed as part of the Navigation Product are listed in the “About”...
Page 253: Copyright Note
This manual may not, in whole or in part, be reproduced or transmitted in any form either electronically or mechanically, including photocopying and recording, without the express written consent of Alpine Electronics, Inc. © 2015 – Alpine Electronics, Inc. All rights reserved. © 2015 – NNG Kft. All rights reserved. data: ©...

This manual is also suitable for:

X308u Ine-w987hd

Alpine X409 Owner's Manual

Quick Links

Related Manuals for Alpine X409

Summary of Contents for Alpine X409