Cannon 10460G Instructions For Installation And Use Manual page 18

Installation
For models supplied without a plug, fit a standard plug, suitable
for the load indicated on the rating plate, onto the cable and
connect to a suitable socket. To connect directly to the mains
supply, a double-pole switch with a contact separation of at
least 3 mm suitable for the load and complying with current
standards and regulations, must be fitted between the appliance
and the mains supply outlet. The yellow-green earth wire must
not be interrupted by the switch. The supply cable must be in
such a position that no part of it can reach a temperature of 50
°C above room temperature. For installation above a built-
under oven, the hob and the oven must be connected separately
to the electricity supply both for safety reasons and for easy
removal of the oven if necessary. Do not use adapters or
shunts as they could cause heating or burning. Before
connecting to the power supply, make sure that:
• the limiter valve and the domestic system can withstand
the load from the appliance (see rating plate);
• the supply system is efficiently earthed according to
standards and laws in force;
• the socket or double-pole switch are easily accessible
when the appliance is installed.
Important: the wires in the mains lead are coloured in
accordance with the following code:
Green & Yellow
Blue
Brown
As the colours of the wires in the mains lead may not
Burners and nozzles specifications
Table 1
BURNER
C.Rapid
B. Semi-rapid
A. Auxiliary
D. Double flame DC DR (internal)
D. Double Flame DC DR (external)
Supply pressure
This appliance conforms with the following European
Economic Community directives:
- 73/23/EEC of 19/02/73 (Low Voltage) and subsequent
modifications;
- 89/336/EEC of 03/05/89 (Electromagnetic Compatibility)
and subsequent modifications;
- 90/396/EEC of 29/06/90 (Gas) and subsequent
modifications;
- 93/68/EEC of 22/07/93 and subsequent modifications.
- Earth
- Neutral
- Live
Diameter Thermal power
(mm)
Nomin. Reduc.
100 3.00
75 1.65
55 1.00
30 0.90
130 4.10
correspond with the coloured markings identifying the terminals
in your plug, proceed as follows:
Connect the Green & Yellow wire to terminal marked "E" or
or coloured Green or Green & Yellow.
Connect the Brown wire to the terminal marked "L" or
coloured Red.
Connect the Blue wire to the terminal marked "N" or
coloured Black.
FAILURE TO OBSERVE THE ACCIDENT-PREVENTION
REGULATIONS RELIEVES THE MANUFACTURER OF
ALL LIABILITY.
Replacing the cable
Use a rubber cable of the type H05RR-F with a suitable cross
section 3 x 1.5 mm².
The yellow-green earth wire must be 2-3 cm longer than the
other wires.
ENERGY LABEL
Directive 2002/40/EC on the label of electric ovens
Norm EN 50304
Energy consumption for Natural convection
heating mode:
Declared energy consumption for Forced convection Class
heating mode:
By-pass Injector
kW (H.s.*) 1/100 1/100
(mm) (mm)
0.7 40
0.4 30
0.3 27
0.4 30
1.3 57
Nominal
Minimum
Maximum
* At 15°C and 1013 mbar-dry gas
Propane G31
Butane G30
Natural gas G20 H.s. = 37,78 MJ/m
Convection
Fan assisted
Liquid gas
Flow * Injector
g/h
G30 G31
86 218 214
64 120 118
50 73 71
44 65 64
70 298 293
28-30 37
20 25
35 45
H.s. = 50,37 MJ/kg
H.s. = 49,47 MJ/kg
3
Natural gas
Flow*
1/100 l/h
(mm) G20
116 286
96 157
71 95
70 86
110 390
20
17
25
17