Can-Am DS 70 Operator's Manual
  1. Manuals
  2. Brands
  3. Can-Am Manuals
  4. Offroad Vehicle
  5. DS 70
  6. Operator's manual

Can-Am DS 70 Operator's Manual

2008 includes safety, vehicle and maintenance information
Hide thumbs Also See for DS 70:
Table of Contents

Advertisement

Quick Links

See also: Operator's Manual

Advertisement

Table of Contents
loading

Related Manuals for Can-Am DS 70

Summary of Contents for Can-Am DS 70

  • Page 2 In Canada, products are distributed by Bombardier Recreational Products Inc. (BRP). In USA, products are distributed by BRP US Inc. The following trademarks are the property of Bombardier Recreational Prod- ucts Inc.: Can-Am™ DS70 DS90 XP-S vmo2008-020 DR ®™ and the BRP logo are trademarks of Bombardier Recreational Products Inc. or its affiliates.
  • Page 3 FOREWORD Congratulations on your purchase of a new Can-Am™ ATV, category “Y” (youth model). It is backed by the BRP warranty and a network of authorized Can-Am dealers ready to provide the parts, service or accessories you may require. Your dealer is committed to your satis- faction.

  • Page 4: Table Of Contents

    TABLE OF CONTENTS While reading this Operator’s Guide, remember that: Indicates a potential hazard that, if not avoided, could result in serious in- jury or death. NOTICE................7 Notice to Parents .
  • Page 5 3) Front Brake Lever ............68 4) Rear Brake Lever.
  • Page 6 MAINTENANCE INFORMATION MAINTENANCE CHART ............96 GENERAL ..
  • Page 7 WARRANTY BRP LIMITED WARRANTY NORTH AMERICA: 2008 CAN-AM ATV . .. 122 BRP INTERNATIONAL LIMITED WARRANTY: 2008 CAN-AM ATV ..126 BRP EUROPEAN UNION MEMBER STATES LIMITED WARRANTY: 2008 CAN-AM ATVS ..............130 PRIVACY OBLIGATION/DISCLAIMER .
  • Page 8 _______________________...

  • Page 9: Notice

    NOTICE This Operator’s Guide has been pre- pared to acquaint the owner/operator of a new vehicle with the various ve- hicle controls, maintenance and safe operating instructions. It is indispens- able for the proper use of the product. This Operator’s Guide uses the follow- ing symbols.
  • Page 10 – BRP recommends that all ATV riders take a training course. For safety and training information, contact an authorized Can-Am dealer or call the Specialty Vehi- cle Institute of America (SVIA) at 1 800 887-2887 or in Canada, the Canada Safety Council (CSC) at 1 613 739-1535 ext.

  • Page 11: Introduction

    INTRODUCTION Your dealer should have provided you with some basic information on the particular controls and features of your new youth model vehicle. Please take the time to study this Operator’s Guide and all on-product warning labels as well as the SAFETY VIDEO that came with this vehicle.
  • Page 12 ______________________...

  • Page 13: Safety Information

    SAFETY INFORMATION ____________ ___________ SAFETY INFORMATION...

  • Page 14: Special Safety Messages

    Take a train- ing course. All operators should receive training from a certified instructor. Contact an authorized Can-Am dealer for more informa- tions. USA and Canada only: to find out about available training course nearest you, call the Specialty Ve-...
  • Page 15 Always go slowly and be extra careful when operating on unfa- miliar terrain. Always be alert to changing terrain conditions when operating this vehicle. Never operate rough, slippery or loose terrain un- til you have learned and practiced the skills necessary to control this vehicle on such terrain.
  • Page 16 Operator’s Guide. Never load a youth model vehicle. MORE INFORMATION ABOUT ATV SAFETY, contact an authorized Can-Am dealer to find out about available training courses nearest you. USA and Canada only: call the Specialty Vehicle Institute of Amer- ica (SVIA) at 1 800 877-2887 or in Canada, the Canada safety Council (CSC) at 1 613 739-1535 ext.

  • Page 17: Operation Warnings

    Beginning and inexperienced operators should complete a training course. They should then regularly practice the skills learned in the course and the operating techniques described in this Operator’s Guide. For more information about the training course, contact an authorized Can-Am dealer. ____________ WARNING WARNING...
  • Page 18 WARNING POTENTIAL HAZARD Failure to follow the age recommendations for this vehicle. WHAT CAN HAPPEN Use by children of ATVs that are not recommended for their age can lead to severe injury or death of the child. Even though a child may be within the age group for which this vehicle is recommended, he may not have the skills, abilities, or judgment needed to operate this vehicle safely and may be involved in a serious accident.
  • Page 19 WARNING POTENTIAL HAZARD Carrying a passenger on this vehicle. WHAT CAN HAPPEN Greatly reduces your ability to balance and control this vehicle. Could cause an accident, resulting in harm to you and/or your passenger. HOW TO AVOID THE HAZARD Never carry passenger. Even with a long seat that provides unrestricted operator movement, it is not designed nor intended to carry passenger(s).
  • Page 20 WARNING POTENTIAL HAZARD Operating this vehicle on paved surfaces. WHAT CAN HAPPEN The tires are designed for off-road use only, not for use on pavement. Paved surfaces may seriously affect handling and control of this vehicle, and may cause the vehicle to go out of control. HOW TO AVOID THE HAZARD Never operate this vehicle on any paved surfaces, including sidewalks, driveways, parking lots and streets.
  • Page 21 WARNING POTENTIAL HAZARD Operating this vehicle on public streets, roads or highways. WHAT CAN HAPPEN You can collide with another vehicle. HOW TO AVOID THE HAZARD Never operate this vehicle on any public street, road or highway, even a dirt or gravel one. In many states or provinces it is illegal to operate this vehicle on public streets, roads or highways.
  • Page 22 POTENTIAL HAZARD Riding this vehicle without wearing an approved helmet, eye protection and protective clothing. WHAT CAN HAPPEN The following items concern all ATV's operator: – riding without an approved helmet increases the chances of a severe head injury or death in the event of an accident –...
  • Page 23 WARNING POTENTIAL HAZARD Riding this vehicle after consuming alcohol or drugs. WHAT CAN HAPPEN Could seriously affect your judgment. Could cause you to react more slowly. Could affect your balance and perception. Could result in an accident or death. HOW TO AVOID THE HAZARD Never consume alcohol or drugs before or while riding this vehicle.
  • Page 24 WARNING POTENTIAL HAZARD Operating this vehicle at excessive speeds. WHAT CAN HAPPEN Increases your chances of losing control of the vehicle, which can result in an accident. HOW TO AVOID THE HAZARD Always travel at a speed which is proper for the terrain, visibility and op- erating conditions, and your experience.
  • Page 25 WARNING POTENTIAL HAZARD Attempting wheelies, jumps and other stunts. WHAT CAN HAPPEN Increases the chance of an accident, including an overturn. HOW TO AVOID THE HAZARD Never attempt stunts, such as wheelies or jumps. Do not try to show off. ____________ ___________ SAFETY INFORMATION...
  • Page 26 POTENTIAL HAZARD Failure to inspect the vehicle before operating. Failure to properly maintain the vehicle. WHAT CAN HAPPEN Increases the possibility of an accident or equipment damage. HOW TO AVOID THE HAZARD Always inspect your vehicle each time you use it to make sure the vehicle is in safe operating condition.
  • Page 27 WARNING POTENTIAL HAZARD Removing hands from handlebar or feet from the footrests during opera- tion. WHAT CAN HAPPEN Removing even one hand or foot can reduce your ability to control the vehicle or could cause you to lose your balance and fall off the vehicle. If you remove a foot from the footrests, your foot or leg may come into contact with the rear wheels, which could injure you or cause an accident.
  • Page 28 WARNING POTENTIAL HAZARD Failure to use extra care when operating this vehicle on unfamiliar terrain. WHAT CAN HAPPEN You can come upon hidden rocks, bumps, or holes, without enough time to react. Could result in the vehicle overturning or loss of control. HOW TO AVOID THE HAZARD Go slowly and be extra careful when operating on unfamiliar terrain.
  • Page 29 WARNING POTENTIAL HAZARD Failure to use extra care when operating on excessively rough, slippery or loose terrain. WHAT CAN HAPPEN Could cause loss of traction or vehicle control, which could result in an accident, including an overturn. HOW TO AVOID THE HAZARD Do not operate on excessively rough, slippery or loose terrain until you have learned and practiced the skills necessary to control this vehicle on such terrain.
  • Page 30 WARNING POTENTIAL HAZARD Turning improperly. WHAT CAN HAPPEN Vehicle could go out of control, causing a collision or overturn. HOW TO AVOID THE HAZARD Always follow proper procedures for turning as described further in this Operator’s Guide. Practice turning at low speeds before attempting to turn at faster speeds.
  • Page 31 WARNING POTENTIAL HAZARD Operating on excessively steep hills. WHAT CAN HAPPEN The vehicle can overturn more easily on extremely steep hills than on level surfaces or small hills. HOW TO AVOID THE HAZARD Never operate this vehicle on hills too steep for the vehicle or for your abil- ities.
  • Page 32 WARNING POTENTIAL HAZARD Climbing hills improperly. WHAT CAN HAPPEN Could cause loss of control or cause vehicle to overturn. HOW TO AVOID THE HAZARD Always follow proper procedures for climbing hills as described further in this Operator’s Guide. Always check the terrain carefully before you start up any hill. Never climb hills with excessively slippery or loose surfaces.
  • Page 33 WARNING POTENTIAL HAZARD Going down a hill improperly. WHAT CAN HAPPEN Could cause loss of control or cause vehicle to overturn. HOW TO AVOID THE HAZARD Always follow proper procedures for going down hills as described further in this Operator’s Guide. NOTE: A special technique is required when brak- ing as you go down a hill.
  • Page 34 WARNING POTENTIAL HAZARD Improperly crossing hills or turning on hills. WHAT CAN HAPPEN Could cause loss of control or cause vehicle to overturn. HOW TO AVOID THE HAZARD Never attempt to turn the vehicle around on any hill until you have mas- tered the turning technique as described further in this Operator’s Guide on level ground.
  • Page 35 WARNING POTENTIAL HAZARD Stalling, rolling backwards or improperly dismounting while climbing a hill. WHAT CAN HAPPEN Could result in vehicle overturning. HOW TO AVOID THE HAZARD Use proper gear and maintain steady speed when climbing a hill. If you lose all forward speed: Keep your weight uphill.
  • Page 36 WARNING POTENTIAL HAZARD Improperly operating over obstacles. WHAT CAN HAPPEN Could cause loss of control or a collision. Could cause the vehicle to overturn. HOW TO AVOID THE HAZARD Before operating in a new area, check for obstacles. Never attempt to ride over large obstacles, such as large rocks or fallen trees.
  • Page 37 WARNING POTENTIAL HAZARD Skidding or sliding improperly. WHAT CAN HAPPEN You may lose control of this vehicle. You may also regain traction unexpectedly, which may cause the vehicle to overturn. HOW TO AVOID THE HAZARD Learn to safely control skidding or sliding by practicing at low speeds and on level smooth terrain.
  • Page 38 WARNING POTENTIAL HAZARD Operating this vehicle through deep or fast flowing water. WHAT CAN HAPPEN Tires may float, causing loss of traction and loss of control, which could lead to an accident. HOW TO AVOID THE HAZARD Never operate this vehicle in fast flowing water or in water deeper than that specified further in this Operator’s Guide.
  • Page 39 WARNING POTENTIAL HAZARD Operating this vehicle with improper tires, or with improper or uneven tire pressure. WHAT CAN HAPPEN Use of improper tires on this vehicle, or operation of this vehicle with im- proper or uneven tire pressure, may cause loss of control, tire blow outs, tire to move around on its rim, and increases the risk of an accident.
  • Page 40 All parts and accessories added to this vehicle should be approved by BRP and should be installed and used according to instructions. If you have questions, consult an authorized Can-Am dealer. NEVER install passenger seat or use the racks to carry a passenger.
  • Page 41 WARNING POTENTIAL HAZARD Overloading this vehicle or carrying or towing cargo improperly. WHAT CAN HAPPEN Could cause changes in vehicle handling which could lead to an accident. HOW TO AVOID THE HAZARD Never load cargo on this vehicle. Never tow cargo or another vehicle with this vehicle. ____________ ___________ SAFETY INFORMATION...
  • Page 42 POTENTIAL HAZARD Transporting flammable or dangerous material can lead to explosions. WHAT CAN HAPPEN This can cause serious injury or death. HOW TO AVOID THE HAZARD Never transport flammable or dangerous material. While reading this Operator’s Guide, remember that: Indicates a potential hazard that, if not avoided, could result in serious in- jury or death.

  • Page 43: Riding The Vehicle

    ATV clubs, a recognized ATV train- ing organization or contact an autho- rized Can-Am dealer. USA and Canada only: To find out about available training course nearest you, call the Specialty Vehicle Institute...
  • Page 44 – Start engine, remove parking brake and drive forward slowly a few feet then apply all brakes individually to test them. Correct any problem you may have found before riding. See an autho- rized Can-Am dealer as necessary. ___________ SAFETY INFORMATION ___________...

  • Page 45: Clothing

    Clothing Actual weather conditions should help you decide how to dress. However, it is important that the operator always wear the appropriate protective clothing and apparel, including an approved helmet, eye protection, boots, gloves, long sleeved shirt and pants. This type of clothing will provide you protection from some of the minor hazards you may encounter en route.

  • Page 46: Carrying Loads

    Carrying Loads This vehicle is designed specifically to carry an operator only. Even with a long seat that provide unrestricted operator movements, it is not designed nor intend- ed to carry passenger(s). NEVER install passenger's seat or use the racks or their location to carry passenger(s).

  • Page 47: Design Limitation

    Design Limitation Although the vehicle is exceptionally rugged for its class, it is still a light vehicle by definition and its operation must be restricted to its proper purpose. The addition of weight to any part of the vehicle changes its gravitational stability and modifies its performance.

  • Page 48: Downhill Driving

    It is also wise to know the terrain condition on the other side of the hill or bank. All too often there exists a sharp drop-off that is impossible to negotiate or descend. Downhill Driving This vehicle can climb slopes that are steeper than it can safely descend. There- fore, it is essential to assure that a safe route exists to descend a slope before you climb it.
  • Page 49 Even though there is an adequate suspensions system on this vehicle there are “washboard” or rough terrain conditions that will make you feel uncomfortable and even cause back injury. “Posting“ or riding in a crouched position will often be required. Slow down and allow your flexed legs to absorb impact. This vehicle is not designed for riding on roads or highways.
  • Page 50 Water will affect the braking ability of your vehicle. Make sure you dry the brakes by applying them several times after the vehicle leaves the water. Mud or marsh lands may be encountered near water. Be prepared for sudden “holes“ or changes in depth. Similarly so, be watchful of hazards such as rocks, logs, etc., partially covered by vegetation.
  • Page 51 When riding in sand dunes it is advisable to equip the vehicle with an antenna type safety flag. This will help make your location more visible to others over the next sand dune. Proceed carefully should you see another safety flag ahead. Since the antenna type safety flag can snag and rebound on your body if caught, do not use it in areas where there are low hanging branches or obstacles.
  • Page 52 Uphill Keep your body weight forward towards the top of the hill. Keep your feet on the footpegs and shift into low gear then accelerate and when necessary, change gear quickly as you climb. Do not over-speed since this may cause the front of the vehicle to lift from the ground and fall back on you.
  • Page 53 Downhill Keep your body weight rearwards. Apply the brake gradually to prevent skidding. Do not “coast“ down the slope using solely engine compression or in neutral gear. While reading this Operator’s Guide, remember that: Indicates a potential hazard that, if not avoided, could result in serious in- jury or death.

  • Page 54: Routine Maintenance

    Part of your responsibility towards safety is to respect the contents of this Op- erator’s Guide. It provides valuable advice on how to properly take care of your vehicle. If further assistance is required your authorized Can-Am dealer is always willing to help.
  • Page 55 Modification of the vehicle to increase speed and performance may violate the terms and conditions of your vehicle limited warranty. In addition, certain modifi- cations including the removal of engine or exhaust components are illegal under most laws. Changing the wheel and/or tire size may affect the stability of the vehicle. Incor- rect tire pressure may lead to blow outs or cause a tire to move around on its rim and become lost or damaged.

  • Page 56: Hang Tag

    HANG TAG This vehicle comes with a hang tag containing important information. vmo2008-008-066_aen TYPICAL USA and Canada Only vmo2006-005-009_en ___________ SAFETY INFORMATION ___________...

  • Page 57: Location Of The Important Labels

    The following labels are on your vehicle and they should be considered perma- nent parts of the vehicle. If missing or damaged, they can be replaced free of charge. See an authorized Can-Am dealer. NOTE: The following illustrations used in this Operator’s Guide are a general representation only.
  • Page 58 Label 1 Label 2 ___________ DS70 DS90/DS90 X vmo2008-008-002_aen TYPICAL SAFETY INFORMATION Label 3 Label 4 ___________...
  • Page 59 Label 5 USA and Canada Models vmo2007-002-002 LOCATED UNDER REAR FENDER ____________ ___________ SAFETY INFORMATION...
  • Page 60 ___________ ___________ SAFETY INFORMATION...

  • Page 61: Vehicle Information

    VEHICLE INFORMATION _____________________...

  • Page 62: How To Identify Your Vehicle

    These numbers are required by the authorized Can-Am dealer to complete warranty claims properly. No warranty will be allowed by BRP if the engine identification...

  • Page 63: Noise Emission Control System Regulation

    NOISE EMISSION CONTROL SYSTEM REGULATION USA and Canada Only Tampering with Noise Control System is Prohibited! U.S. Federal law and Canadian provincial laws may prohibit the following acts or the causing there of: 1. The removal or rendering inoperative by any person other than for purposes of maintenance, repair or replacement of any device or element of design incorporated into any new vehicle for the purpose of noise control prior to its sale or delivery to the ultimate purchaser or while it is in use or,...

  • Page 64: Emission Requirements

    EMISSION REQUIREMENTS USA Only The California Air Resources Board (CARB) requires that your vehicle complies with applicable exhaust emissions standards during its useful life, when operated and maintained according to the instructions supplied. A non-compliance RED label (as well as a GREEN label) is obtained annually dur- ing California Vehicle registration.

  • Page 65: Break-In Period

    10 hours or 30 days after the purchase, whichever comes first, your vehicle be inspected by an autho- rized Can-Am dealer. This inspection will give you the opportunity to dis- cuss the unanswered questions you may have encountered during the first hours of operation.

  • Page 66: Controls/Instruments/Equipment

    CONTROLS/INSTRUMENTS/EQUIPMENT NOTE: Some controls/instruments/equipment are optional. vmo2008-008-063_a TYPICAL ______________________...
  • Page 67 vmo2008-008-064_a TYPICAL _____________________...
  • Page 68 vmo2008-008-065_a TYPICAL While reading this Operator’s Guide, remember that: Indicates a potential hazard that, if not avoided, could result in serious in- jury or death. ______________________ WARNING...

  • Page 69: Throttle Lever

    NOTE: This section gives basic func- tions of the various controls of your ve- hicle. For more details of how to op- erate one control in conjunction with some others, refer to OPERATING IN- STRUCTIONS further in this section. 1) Throttle Lever When pushed, it increases the engine speed that allows the engagement of the transmission.

  • Page 70: Front Brake Lever

    Refer to SPEED LIMITER ADJUST- MENT in FUEL SYSTEM section for proper adjustment. WARNING Improper adjustment of the speed limiter screw could damage throt- tle cable and impair throttle lever operation. Failure to follow ad- justment recommendations could lead to an accident resulting in severe injuries including the pos- sibility of death.

  • Page 71: Transmission Lever

    All Models except DS90 X vmo2008-020-014_a REAR BRAKE LEVER Step 1: Squeeze brake lever and maintain Step 2: Move lever lock DS90 X Only vmo2008-020-014_a REAR BRAKE LEVER Step 1: Squeeze brake lever and maintain Step 2: Push lever lock All Models To release mechanism: brake lever.
  • Page 72 vmo2008-008-011_e 1. Engine stop switch 2. Engine start button 3. Daytime running lights switch (if so equipped) 4. Choke lever Engine Stop Switch This switch can be used to stop engine and as an emergency control. The engine will turn over but will not start if the engine stop switch is placed in the OFF position.

  • Page 73: Indicator Lamps

    vmo2008-008-010_b 1. Daytime running lights switch 2. OFF position 3. ON position Choke Lever This device features a variable lever to ease engine cold start. Position OFF is for normal use with a warm engine. vmo2008-008-011_c OFF POSITION The full choke position is used for low- er engine temperature.

  • Page 74: Ignition Switch

    9) Ignition Switch Key-operated, 2-position switch: OFF and ON. vmo2008-008-012_a IGNITION SWITCH 1. OFF position 2. ON position Insert key in switch and turn to ON position. To remove key, turn key to OFF position then pull it out. NOTE: While engine can be stopped by turning ignition key to OFF posi- tion, we recommend the engine be stopped by the engine stop switch.

  • Page 75: Engine Oil Dipstick

    vmo2008-008-014_a LH SIDE OF VEHICLE 1. Align this pointer toward the desired position Stops fuel supply to carburetor. CAUTION: Turn valve to OFF posi- tion when vehicle is not being op- erated or when transporting. Allows fuel to flow to carburetor. This is the normal position for operation of the vehicle.

  • Page 76: Seat Latch Knob

    mmo2008-008-052_a OTHERS 1. Footpeg 14) Seat Latch Knob Located underneath rear fender, near rear bumper. It allows the removal of seat to give access to engine compart- ment. Pull knob to release seat. vmo2008-008-016_a TYPICAL 1. Seat release knob Seat Removal Pull latch while gently lifting rear of seat.

  • Page 77: Kick Start Pedal

    vmo2008-008-017_a 1. Fuse holder 16) Kick Start Pedal The kick start pedal is provided as an emergency starting device. Follow the usual starting procedure; but use the kick start pedal instead of the electric starter. Refer to EMER- GENCY MANUAL STARTING in OPER- ATING INSTRUCTIONS section.
  • Page 78 WARNING When engine is running, always engage the NEUTRAL position on the transmission lever and apply parking brake before opening cov- er. Never leave any heavy or loose breakable objects in the storage compartment. Always latch cover before riding. ______________________...

  • Page 79: Liquids

    LIQUIDS While reading this Operator’s Guide, remember that: Indicates a potential hazard that, if not avoided, could result in serious in- jury or death. This section specifies the recom- mended liquids of your vehicle and procedures on how to check their lev- els.

  • Page 80: Fuel

    Fuel Recommended Fuel Use unleaded gasoline available from most service stations or oxygenated fuel containing a maximum total of 10% of ethanol or methanol or both. The gasoline used must have the following recommended minimum octane number. OCTANE NUMBER Inside North America Outside North America CAUTION: Never experiment with other fuels.

  • Page 81: Engine Oil Level

    Oil Viscosity Chart XP-S 5W 40 Synthetic Oil (P/N 293 600 039) SAE 0W 30 SAE 5W 30 SAE 10W 30 XP-S 10W 40 Mineral Oil (P/N 219 700 346) SAE 15W 40 SAE 20W 50 Temperature Range 50°C (122°F) 40°C (104°F) 30°C (86°F) 20°C (68°F)

  • Page 82: Brake Fluid

    NOTE: A low level may indicate leaks or worn brake pads. See an autho- rized Can-Am dealer. Front and Rear Brake Lever Fluid Reservoir Brake fluid reservoirs are located on the handlebar above brake levers.

  • Page 83: Tires And Rims

    TIRES AND RIMS While reading this Operator’s Guide, remember that: Indicates a potential hazard that, if not avoided, could result in serious in- jury or death. Tire Pressure WARNING Tire pressure greatly affects vehi- cle handling and stability. Under- pressure may cause tire to deflate and rotate on wheel.

  • Page 84: Operating Instructions

    OPERATING INSTRUCTIONS Starting the Engine WARNING Always proceed with the pre- operation check as described in the SAFETY INFORMATION sec- tion prior to operating the vehicle. Always check the proper oper- ation of critical controls, safety features and mechanical compo- nents before starting.
  • Page 85 vmo2008-008-011_b 1. Engine start button CAUTION: Do not hold start button more than 10 seconds. A rest peri- od should be observed between the cranking cycles to let starter cool down. Pay attention to battery; do not discharge it. NOTE: Throttle assist may be used to help starting the engine faster.

  • Page 86: Stopping The Engine

    mmo2008-008-051_a TYPICAL 1. Kick start pedal Repeat this procedure completely if necessary. Stopping the Engine WARNING Avoid parking on a slope. Release throttle and completely stop the vehicle. Apply the parking brake. Push the engine stop switch to OFF position. Turn key in ignition switch to OFF po- sition.

  • Page 87: Suspension Adjustment

    SUSPENSION ADJUSTMENT WARNING Left and right front shock adjust- ment must always be set at the same position. Never adjust one shock only. Uneven adjustment can cause poor handling and loss of stability, which could lead to an accident. Spring Preload Adjustment Shorten the spring for a firmer ride and rough road condition.

  • Page 88: Special Procedures

    Vehicle Immersion Should the vehicle become immersed, it will be necessary to take it to an authorized Can-Am dealer as soon as possible. DO NOT START THE EN- GINE! Immersion of the vehicle can cause serious damage if the correct restart procedure is not followed.

  • Page 89: Transporting The Vehicle

    TRANSPORTING THE VEHICLE While reading this Operator’s Guide, remember that: Indicates a potential hazard that, if not avoided, could result in serious in- jury or death. When transporting a vehicle, se- cure vehicle to trailer with suitable tie-downs. Using ordinary ropes is not recommended.

  • Page 90: Troubleshooting

    – Check that ignition switch and/or engine stop switch is/are at the ON posi- tion. – Start engine with spark plug grounded to the engine away from spark plug hole. If no spark appears, replace spark plug. – If trouble persists, contact an autho rized Can-Am dealer. ______________________...
  • Page 91 • Apply parking brake and stop engine. • Let engine cool down. • See an authorized Can-Am dealer as soon as possible. – If overheating persists, contact an authorized Can-Am dealer. 5. Air filter/box plugged or dirty. – Check air filter and clean if necessary.
  • Page 92 – Check air filter and clean if necessary. – Check the position of the air intake tube. 4. CVT dirty or wear. – Contact an authorized Can-Am dealer. THE RPM INCREASES BUT THE VEHICLE DOES NOT MOVE 1. CVT is defective.

  • Page 93: Specifications

    SPECIFICATIONS MODEL ENGINE Type Number of cylinder Displacement Starting TRANSMISSION Transmission CARBURETION Carburetor Idle speed ELECTRICAL Ignition type Spark plug Number of spark plug Battery Starting system Daytime running light bulb Taillight bulb Fuse DS70 4-stroke, forced air cooled Single horizontal cylinder 69.36 cc (4.23 cu.
  • Page 94 MODEL SUSPENSION Type Travel Shock absorber TIRES Pressure Size WHEELS Size Wheel nuts torque BRAKES Front Rear Parking device ______________________ DS70 Independent suspension – A-arm Front DS90 X: independent suspension Rear Front DS90 X: 178 mm (7 in) 160 mm (6.3 in) Rear DS90 X: 229 mm (9 in) Front...
  • Page 95 MODEL DIMENSIONS Dry weight Overall length Overall width Overall height Wheel base Ground clearance LIQUIDS Engine Oil type Gearbox Oil Type Type Fuel Octane CAPACITIES Engine oil Gearbox oil Fuel tank Ampere A•h: Ampere hour RPM: Revolution Per Minute Because of our ongoing commitment to product quality and innovation, BRP re- serves the right, at any time, to make changes in design and specifications and/or to make additions to, or improvements in its products without imposing any obli- gation upon itself to install them on its products previously manufactured.
  • Page 96 ______________________...

  • Page 97: Maintenance Information

    MAINTENANCE INFORMATION _____________________...

  • Page 98: Maintenance Chart

    Carburetor ______________________ PERIODIC MAINTENANCE CHART INITIAL INSPECTION 10 HOURS OR 30 DAYS (To be performed by an authorized Can-Am dealer. The initial maintenance is very important and must not be neglected.) WEEKLY MONTHLY ONCE A YEAR OR EVERY 100 HOURS...
  • Page 99 GEARBOX Gearbox oil PERIODIC MAINTENANCE CHART INITIAL INSPECTION 10 HOURS OR 30 DAYS (To be performed by an authorized Can-Am dealer. The initial maintenance is very important and must not be neglected.) WEEKLY MONTHLY ONCE A YEAR OR EVERY 100 HOURS...
  • Page 100 Fasteners tightness ______________________ PERIODIC MAINTENANCE CHART INITIAL INSPECTION 10 HOURS OR 30 DAYS (To be performed by an authorized Can-Am dealer. The initial maintenance is very important and must not be neglected.) WEEKLY MONTHLY ONCE A YEAR OR EVERY 100 HOURS...

  • Page 101: General

    WARNING All maintenance should be done by an adult or an authorized Can-Am dealer. Do not allow chil- dren to attempt repairs or mainte- nance. The following covers the maintenance items that can be performed by the customer if desired.

  • Page 102: Engine

    ENGINE Oil Change Oil change should be done with a warm engine. WARNING The engine oil can be very hot. Wait until engine oil is warm. Ensure vehicle is on a level surface. Remove dipstick. vmo2008-008-021_a TYPICAL — RH SIDE OF ENGINE 1.

  • Page 103: Air Filter Housing Draining

    vmo2006-014-037_a TYPICAL 1. Cover 2. O-ring 3. Spring 4. Strainer Wipe out any oil spillage on engine. Reinstall oil strainer, spring and O-ring. Torque to 42 N•m (31 lbf•ft). Verify drain plug washer condition and replace it if necessary. Clean washer area on engine and drain plug, then reinstall plug and torque it to 22 N•m (16 lbf•ft).

  • Page 104: Air Filter Cleaning

    Air Filter Cleaning vmo2008-008-036_a 1. Air filter location Removal mmo2008-008-053_a REMOVE AIR FILTER BOX COVER 1. Screws mmo2008-008-054_a REMOVE AIR FILTER FROM HOUSING 1. Air filter Cleaning Pour cleaning solution (P/N 219 700 341) or an equivalent into a bucket. Put the filter in to soak.

  • Page 105: Spark Arrester Cleaning

    Clean air injection valve cover before removing. Remove cover to gain access to air filter. vmo2008-020-001_a 1. Remove screws Remove filter from air injection valve. vmo2007-008-004_a TYPICAL 1. Air injection valve 2. Screen 3. Air filter Clean air filter and the inside of air in- jection valve using pressurized air.

  • Page 106: Transmission (Cvt)

    TRANSMISSION (CVT) Drive Belt Inspection See an authorized Can-Am dealer to check the width and the condition of drive belt. CVT Cover Drain Plug Any time you suspect that water has entered the CVT cover, drain the CVT housing by removing the drain tube plug.

  • Page 107: Gearbox

    GEARBOX Oil Change Place the vehicle on a level surface. Remove the air filter housing from the vehicle. vmo2008-008-036_a 1. Air filter housing vmo2008-008-058_a 1. Remove screws 2. Loosen clamp vmo2008-008-062_a REMOVE AIR FILTER HOUSING Clean drain plug and oil filling plug area then remove the gearbox drain plug.
  • Page 108 CAUTION: Do not use other unrec- ommended types of oil when ser- vicing. Do not mix with other types of oil. Reinstall oil filling plug. Reinstall all removed parts. _____________________...

  • Page 109: Fuel System

    Throttle Cable Inspection Check throttle lever free-play, adjust if necessary. If correct adjustment is unattainable, see an authorized Can-Am dealer. Inspect throttle cable for excessive wear, kinking or fraying. Ensure cable moves freely. Replace throttle cable if any signs of wear, fraying or other damage are found.
  • Page 110 WARNING Adults should always limit the maximum restricted speed with- in the ability and capacity of the child to operate the vehicle safely. Never allow the child to adjust the speed limiter. To adjust speed limiter screw, loosen lock nut then, turn speed limiter screw accordingly.

  • Page 111: Electrical

    ELECTRICAL WARNING Unless otherwise indicated, al- ways turn ignition switch to the OFF position before performing any maintenance or repair on elec- trical system. Spark Plug Removal/ Inspection vmo2008-008-033_a TYPICAL — RH SIDE OF VEHICLE 1. Spark plug location Removal vmo2008-008-034_a UNPLUG SPARK PLUG CABLE 1.

  • Page 112: Battery Removal

    Battery Removal WARNING Never charge a battery while in- stalled in vehicle. These vehicles are equipped with a VRLA battery (Valve Regulated Lead Acid). It is a maintenance-free type battery, there is no need to add water to adjust electrolyte level. CAUTION: Never remove the bat- tery sealing cap.

  • Page 113: Daytime Running Lights

    Daytime Running Lights vmo2008-008-038_a REMOVE RUBBER PROTECTOR 1. Rubber protector vmo2008-008-039_a PUSH AND TURN BULB HOLDER COUNTERCLOCKWISE 1. Bulb holder vmo2008-008-040_a PULL ON BULB TO REMOVE THEN REPLACE BULB 1. Bulb _____________________...

  • Page 114: Drive Train

    DRIVE TRAIN Drive Chain Cleaning/ Lubrication/Adjustment Inspection Inspect the chain for damaged links and rollers. Replace chain if any damage is found. CAUTION: Replace chain, sprocket axle and pinion together to prevent rapid chain and sprocket wear. Check the free-play of drive chain and adjust if necessary.

  • Page 115: Drive Chain Roller Inspection

    FREE-PLAY: 44 TO 57 MM (1-3/4 TO 2-1/4 IN) When properly adjusted, tighten chain adjuster lock nut. Then, tighten drive axle locking bolts to 69 N•m (51 lbf•ft). Drive Chain Roller Inspection Inspect the drive chain roller around swing arm pivot member for exces- sive wear and damage.
  • Page 116 Wheel Bearing Condition Push and pull the wheels from the up- per edge to feel the play. See an au- thorized Can-Am dealer if there is any play. TYPICAL _____________________...

  • Page 117: Steering System

    STEERING SYSTEM Lubrication All Models except DS90 X Lubricate front knuckles. Use syn- thetic grease (P/N 293 550 033) or an equivalent. There is a grease fitting on each knuckle. vmo2008-008-037_a TYPICAL 1. Grease fitting _____________________...

  • Page 118: Brakes

    BRAKE PAD MINIMUM 1 mm (.0394 in) THICKNESS See your authorized Can-Am dealer if a problem is detected concerning the brake system. Inspection (mechanical) All Models except DS90 X WARNING Any brake system repair should be performed by an authorized Can-Am Dealer.

  • Page 119: Rear Brake Lever Adjustment

    vmr2008-106-010_a 1. Adjustment screws on lever vmr2008-102-009_a 1. Adjustment screws on cables Press brake lever. Adjust cable link so it is parallel to ca- ble support. Turn adjustment screws on cable (not at lever) as required. vmr2008-106-011_a 1. Cable link 2.

  • Page 120: Body/Frame

    Replace or have damaged parts re- paired. Fasteners Inspection Check fastener condition and tight- ness on the vehicle. Retighten as required. Seat Latch Inspection Remove seat and check latch mech- anism for wear. See an authorized Can-Am dealer for parts replacement if damaged. _____________________...

  • Page 121: Storage And Preseason Preparation

    CHART. When a vehicle is not in use for more than one month, proper storage is a necessity. See an authorized Can-Am dealer for proper procedures. When using your vehicle after storage, a preparation is required. See an au- thorized Can-Am dealer for proper pro- cedures.
  • Page 122 _____________________...
  • Page 123 WARRANTY _____________________...

  • Page 124: Brp Limited Warranty North America: 2008 Can-Am

    All genuine Can-Am ATV parts and accessories, installed by an authorized BRP dealer (as hereinafter defined) at the time of delivery of the 2008 Can-Am ATV, carry the same warranty as that of the Can-Am ATV. A GPS receiver may be supplied by BRP as standard equipment on certain 2008 Can-Am ATV's.
  • Page 125 • Damage caused by abuse, abnormal use, neglect or operation of the product in a manner inconsistent with the recommended operation described in the Can-Am ATV Operator’s Guide; • Damage resulting from accident, submersion, fire, theft, vandalism or any act of God;...
  • Page 126 This warranty coverage is available only if each of the following conditions has been fulfilled: • The 2008 Can-Am ATV must be purchased as new and unused by its first owner from a BRP dealer authorized to distribute Can-Am ATVs in the country in which the sale occurred (“BRP dealer”);...
  • Page 127 BRP’s obligations under this warranty are limited to, at its sole discretion, repair- ing parts found defective under normal use, maintenance and service, or replac- ing such parts with new genuine Can-Am ATV parts without charge for parts and labor, at any authorized BRP dealer during the warranty coverage period.

  • Page 128: Brp International Limited Warranty: 2008 Can-Am

    Can-Am distributor/dealer (as hereinafter defined) at the time of delivery of the 2008 Can-Am ATV, carry the same warranty as that of the Can-Am ATV. Use of the product for racing or any other competitive activity, at any point, even by a previous owner will render this warranty null and void.
  • Page 129 This warranty coverage is available only if each of the following conditions has been fulfilled: • The 2008 Can-Am ATV must be purchased as new and unused by its first owner from a Can-Am distributor/dealer authorized to distribute Can-Am ATVs in the country in which the sale occurred (“Can-Am distributor/dealer”);...
  • Page 130 BRP’s obligations under this warranty are limited to, at its sole discretion, repair- ing parts found defective under normal use, maintenance and service; or replac- ing such parts with new genuine Can-Am ATV parts without charge for parts and labour, at any authorized Can-Am distributor/dealer.
  • Page 131 For countries within Europe, Middle East, Africa, Russia & CIS, please contact our European office: BRP EUROPE N.V. Consumer Service Center Skaldenstraat 125 9042 Gent Belgium Tel.: + 32-9-218-26-00 For Scandinavian countries, please contact our Finland office: BRP FINLAND OY Service Department Ahjotie 30 Fin-96320 Rovaniemi...

  • Page 132: Brp European Union Member States Limited Warranty: 2008 Can-Am

    All genuine Can-Am ATV parts and accessories, installed by an authorized BRP Distributors/Dealers at the time of delivery of the 2008 Can-Am ATV, carry the same warranty as that of the ATV. Use of the product for racing or any other competitive activity, at any point, even by a previous owner, will render this warranty null and void.
  • Page 133 This warranty coverage is available only if each of the following conditions has been fulfilled: • The 2008 Can-Am ATV must be purchased as new and unused by its first owner from a Can-Am Distributor/Dealer authorized to distribute Can-Am ATVs in the country in which the sale occurred;...
  • Page 134 BRP’s obligations under this warranty are limited to, at its sole discretion, repair- ing parts found defective under normal use, maintenance and service, or replac- ing such parts with new genuine Can-Am parts without charge for parts and labor, at any authorized BRP Distributor/Dealer during the warranty coverage period.
  • Page 135 For countries within Europe, Middle East, Africa, Russia & CIS, please contact our European office: BRP EUROPE N.V. Consumer Service Center Skaldenstraat 125 9042 Gent Belgium Tel.: + 32-9-218-26-00 For Scandinavian countries, please contact our Finland office: BRP FINLAND OY Service Department Ahjotie 30 Fin-96320 Rovaniemi...

  • Page 136: Privacy Obligation/Disclaimer

    PRIVACY OBLIGATION/DISCLAIMER We wish to inform you that your coordinates will be used for safety and warranty purposes. Sometimes, we also use the coordinates of our clients to inform them about our products and to present them offers. Should you prefer not to receive information on our product, services and offers, please let us know by writing to the address below.

  • Page 137: Change Of Address/Ownership

    – mailing one of the following card below; – North America Only: calling at 715 848-4957 (USA) or 819 566-3366 (Canada); – notifying an authorized Can-Am dealer. In case of change of ownership, please join a proof that the former owner agreed to the transfer.
  • Page 138 _____________________...
  • Page 139 Please verify with your dealer to ensure your vehicle has been registered with BRP. While reading this Operator’s Guide, remember that: Indicates a potential hazard that, if not avoided, could result in serious in- jury or death. WARNING...

This manual is also suitable for:

2008 ds 702008 ds 902008 ds 90 x

Table of Contents