Can-Am DS 250 Operator's Manual
  1. Manuals
  2. Brands
  3. Can-Am Manuals
  4. Offroad Vehicle
  5. DS250
  6. Operator's manual
Can-Am DS 250 Operator's Manual

Can-Am DS 250 Operator's Manual

Hide thumbs Also See for DS 250:
Table of Contents

Advertisement

Quick Links

See also: Operator's Manual
WARNING
Read this guide thoroughly. It contains important
safety information.
Minimum recommended operator age: 16 years.
Do not remove this Operator’s Guide from the
vehicle.
2 1 9
0 0 0
4 2 6

Advertisement

Table of Contents
loading

Related Manuals for Can-Am DS 250

Summary of Contents for Can-Am DS 250

  • Page 1 WARNING Read this guide thoroughly. It contains important safety information. Minimum recommended operator age: 16 years. Do not remove this Operator’s Guide from the vehicle. 2 1 9 0 0 0 4 2 6...
  • Page 2 The following trademarks are the property of Bombardier Recreational Prod- ucts Inc.: Can-Am™ XP-S Printed in Canada.(vmo2007-007 DR) ®™ and the BRP logo are trademarks of Bombardier Recreational Products Inc. or its affiliates.
  • Page 3 FOREWORD Congratulations on your purchase of information compo- a new Can-Am™ ATV. It is backed by nents/system descriptions contained the BRP warranty and a network of in this document are correct at the time of publication. BRP, however, authorized Can-Am distributors/deal-...

  • Page 4: Table Of Contents

    TABLE OF CONTENTS While reading this Operator’s Guide, remember that: WARNING Indicates a potential hazard that, if not avoided, could result in serious in- jury or death. NOTICE................7 European Community .
  • Page 5 4) Parking Brake..............65 5) Transmission Lever .
  • Page 6 CARGO AND TRANSPORTATION ..........85 TROUBLESHOOTING .
  • Page 7 STORAGE AND PRESEASON PREPARATION ....... 124 WARRANTY BRP INTERNATIONAL LIMITED WARRANTY: 2007 CAN-AM ATV ..126 PRIVACY OBLIGATION/DISCLAIMER .
  • Page 8 _______________________...

  • Page 9: Notice

    NOTICE European Community This Operator's Guide has been pre- pared to acquaint the owner/operator This warning applies only in the Euro- of a new vehicle with the various ve- pean Countries where on road usage hicle controls, maintenance and safe is allowed.

  • Page 10: Introduction

    INTRODUCTION Your distributor/dealer should have The contents of this Operator's Guide provide riding information which has provided you with some basic infor- been proven reliable by other users. mation on the particular controls and features of your new vehicle. Please They are not intended as a definitive take the time to study this Operator's means of avoiding accidents.

  • Page 11: Safety Information

    SAFETY INFORMATION ____________ ____________ SAFETY INFORMATION...

  • Page 12: Special Safety Messages

    Operator's Guide. instructor. Contact an authorized Always keep both hands on the Can-Am distributor/dealer to find handlebars and both feet on the out about available training course footrests of the vehicle during op- nearest you.
  • Page 13 Never operate this vehicle on hills Always use proper procedures if too steep for the vehicle or for your you stall or roll backwards when climbing a hill. To avoid stalling, abilities. Practice on smaller hills before attempting larger hills. use proper gear and maintain a steady speed when climbing a hill.
  • Page 14 Reduce speed and follow instruc- tions in this manual for carrying car- go or pulling a trailer. Allow greater distance for braking. MORE INFORMATION ABOUT SAFETY, con- tact authorized Can-Am distributor/dealer to find out about available training courses nearest you. ___________ ___________ SAFETY INFORMATION...

  • Page 15: Operation Warnings

    Beginning and inexperienced operators should complete a training course. They should then regularly practice the skills learned in the course and the operating techniques described in this Operator's Guide. For more information about the training course, contact an authorized Can-Am distributor/dealer. ____________ ___________ SAFETY INFORMATION...
  • Page 16 WARNING V00A01Q POTENTIAL HAZARD Failure to follow the age recommendations for this vehicle. WHAT CAN HAPPEN A lack of respect for this age recommendation can lead to severe injury or death of the child. Even though a child may be within the age group for which this vehicle is recommended, he may not have the skills, abilities, or judgment needed to operate this vehicle safely and may be involved in a serious accident.
  • Page 17 WARNING V00A02Q POTENTIAL HAZARD Carrying a passenger on this vehicle. WHAT CAN HAPPEN Greatly reduces your ability to balance and control this vehicle. Could cause an accident, resulting in harm to you and/or your passenger. HOW TO AVOID THE HAZARD Never carry passenger.
  • Page 18 WARNING V00A04Q POTENTIAL HAZARD Operating this vehicle on public streets or roads. WHAT CAN HAPPEN You can collide with another vehicle. Paved surfaces may seriously affect handling and control of the vehicle, and may cause the vehicle to go out of control.
  • Page 19 WARNING V00A06Q POTENTIAL HAZARD Riding this vehicle without wearing an approved helmet, eye protection and protective clothing. WHAT CAN HAPPEN The following items concern all ATV's operator: – riding without an approved helmet increases the chances of a severe head injury or death in the event of an accident –...
  • Page 20 WARNING V00A07Q POTENTIAL HAZARD Riding this vehicle after consuming alcohol or drugs. WHAT CAN HAPPEN Could seriously affect your judgment. Could cause you to react more slowly. Could affect your balance and perception. Could result in an accident or death. HOW TO AVOID THE HAZARD Never consume alcohol or drugs before or while riding this vehicle.
  • Page 21 WARNING V00A08Q POTENTIAL HAZARD Operating this vehicle at excessive speeds. WHAT CAN HAPPEN Increases your chances of losing control of the vehicle, which can result in an accident. HOW TO AVOID THE HAZARD Always travel at a speed which is proper for the terrain, visibility and op- erating conditions, and your experience.
  • Page 22 WARNING V00A09Q POTENTIAL HAZARD Attempting wheelies, jumps and other stunts. WHAT CAN HAPPEN Increases the chance of an accident, including an overturn. HOW TO AVOID THE HAZARD Never attempt stunts, such as wheelies or jumps. Do not try to show off. ___________ ___________ SAFETY INFORMATION...
  • Page 23 WARNING POTENTIAL HAZARD Failure to inspect the vehicle before operating. Failure to properly maintain the vehicle. WHAT CAN HAPPEN Increases the possibility of an accident or equipment damage. HOW TO AVOID THE HAZARD Always inspect your vehicle each time you use it to make sure the vehicle is in safe operating condition.
  • Page 24 WARNING V00A0BQ POTENTIAL HAZARD Removing hands from handlebar or feet from the footrests during opera- tion. WHAT CAN HAPPEN Removing even one hand or foot can reduce your ability to control the vehicle or could cause you to lose your balance and fall off the vehicle. If you remove a foot from the footrests, your foot or leg may come into contact with the rear wheels, which could injure you or cause an accident.
  • Page 25 WARNING V00A0CQ POTENTIAL HAZARD Failure to use extra care when operating this vehicle on unfamiliar terrain. WHAT CAN HAPPEN You can come upon hidden rocks, bumps, or holes, without enough time to react. Could result in the vehicle overturning or loss of control. HOW TO AVOID THE HAZARD Go slowly and be extra careful when operating on unfamiliar terrain.
  • Page 26 WARNING V00A0DQ POTENTIAL HAZARD Failure to use extra care when operating on excessively rough, slippery or loose terrain. WHAT CAN HAPPEN Could cause loss of traction or vehicle control, which could result in an accident, including an overturn. HOW TO AVOID THE HAZARD Do not operate on excessively rough, slippery or loose terrain until you have learned and practiced the skills necessary to control this vehicle on such terrain.
  • Page 27 WARNING V00A0EQ POTENTIAL HAZARD Turning improperly. WHAT CAN HAPPEN Vehicle could go out of control, causing a collision or overturn. HOW TO AVOID THE HAZARD Always follow proper procedures for turning as described further in this Operator's Guide. Practice turning at low speeds before attempting to turn at faster speeds.
  • Page 28 WARNING V00A0QQ POTENTIAL HAZARD Operating on excessively steep hills. WHAT CAN HAPPEN The vehicle can overturn more easily on extremely steep hills than on level surfaces or small hills. HOW TO AVOID THE HAZARD Never operate this vehicle on hills too steep for the vehicle or for your abil- ities.
  • Page 29 WARNING V00A0FQ POTENTIAL HAZARD Climbing hills improperly. WHAT CAN HAPPEN Could cause loss of control or cause vehicle to overturn. HOW TO AVOID THE HAZARD Always follow proper procedures for climbing hills as described further in this Operator's Guide. Always check the terrain carefully before you start up any hill. Never climb hills with excessively slippery or loose surfaces.
  • Page 30 WARNING V00A0GQ POTENTIAL HAZARD Going down a hill improperly. WHAT CAN HAPPEN Could cause loss of control or cause vehicle to overturn. HOW TO AVOID THE HAZARD Always follow proper procedures for going down hills as described further in this Operator's Guide. NOTE: A special technique is required when brak- ing as you go down a hill.
  • Page 31 WARNING V00A0HQ POTENTIAL HAZARD Improperly crossing hills or turning on hills. WHAT CAN HAPPEN Could cause loss of control or cause vehicle to overturn. HOW TO AVOID THE HAZARD Never attempt to turn the vehicle around on any hill until you have mas- tered the turning technique as described further in this Operator's Guide on level ground.
  • Page 32 WARNING V00A0IQ POTENTIAL HAZARD Stalling, rolling backwards or improperly dismounting while climbing a hill. WHAT CAN HAPPEN Could result in vehicle overturning. HOW TO AVOID THE HAZARD Use proper gear and maintain steady speed when climbing a hill. If you lose all forward speed: Keep your weight uphill.
  • Page 33 WARNING V00A0JQ POTENTIAL HAZARD Improperly operating over obstacles. WHAT CAN HAPPEN Could cause loss of control or a collision. Could cause the vehicle to overturn. HOW TO AVOID THE HAZARD Before operating in a new area, check for obstacles. Never attempt to ride over large obstacles, such as large rocks or fallen trees.
  • Page 34 WARNING V00A0KQ POTENTIAL HAZARD Skidding or sliding improperly. WHAT CAN HAPPEN You may lose control of this vehicle. You may also regain traction unexpectedly, which may cause the vehicle to overturn. HOW TO AVOID THE HAZARD Learn to safely control skidding or sliding by practicing at low speeds and on level smooth terrain.
  • Page 35 WARNING V00A0LQ POTENTIAL HAZARD Operating this vehicle through deep or fast flowing water. WHAT CAN HAPPEN Tires may float, causing loss of traction and loss of control, which could lead to an accident. HOW TO AVOID THE HAZARD Never operate this vehicle in fast flowing water or in water deeper than that specified further in this Operator's Guide.
  • Page 36 WARNING V00A0MQ POTENTIAL HAZARD Improperly operating in reverse. WHAT CAN HAPPEN You could hit an obstacle or person behind the vehicle, resulting in serious injury. HOW TO AVOID THE HAZARD When you select reverse gear, make sure there are no obstacles or people behind the vehicle.
  • Page 37 WARNING V00A0OQ POTENTIAL HAZARD Operating this vehicle with improper tires, or with improper or uneven tire pressure. WHAT CAN HAPPEN Use of improper tires on this vehicle, or operation of this vehicle with im- proper or uneven tire pressure, may cause loss of control, tire blow outs, tire to move around on its rim and increases the risk of an accident.
  • Page 38 All parts and accessories added to this vehicle should be approved by BRP and should be installed and used according to instructions. If you have questions, consult an authorized Can-Am distributor/dealer. NEVER install passenger seat or use the racks to carry a passenger.
  • Page 39 WARNING V00A0PQ POTENTIAL HAZARD Overloading this vehicle or carrying or towing cargo improperly. WHAT CAN HAPPEN Could cause changes in vehicle handling which could lead to an accident. HOW TO AVOID THE HAZARD Never exceed the stated load capacity for this vehicle including operator, as well as other loads and added accessories.
  • Page 40 WARNING V03M01Q POTENTIAL HAZARD Transporting flammable or dangerous material can lead to explosions. WHAT CAN HAPPEN This can cause serious injury or death. HOW TO AVOID THE HAZARD Never transport flammable or dangerous material. While reading this Operator’s Guide, remember that: WARNING Indicates a potential hazard that, if not avoided, could result in serious in- jury or death.

  • Page 41: Riding The Vehicle

    RIDING THE VEHICLE To fully appreciate the pleasures and excitement of riding this vehicle, there are some basic rules and tips that you MUST follow. Some may be new to you while others may be common sense or obvious. Nonetheless, we ask that you take a few minutes to read this Operator's Guide completely before you operate this vehicle.

  • Page 42: Pre-Operation Check

    Correct any problem you may have It must return to idle position when found before riding. See an autho- released. rized Can-Am distributor/dealer as • Activate the brake lever and brake necessary. pedal to make sure the brakes fully apply. Lever and pedal must fully return when released.

  • Page 43: Clothing

    Clothing Actual weather conditions should help you decide how to dress. However, it is important that the operator always wear the appropriate protective clothing and apparel, including an approved helmet, eye protection, boots, gloves, long sleeved shirt and pants. This type of clothing will provide you protection from some of the minor hazards you may encounter en route.

  • Page 44: Carrying Loads

    Working with your Vehicle Your vehicle can help you perform some LIGHT tasks. A variety of accessories are available from your authorized Can-Am distributor/dealer. However, always respect the load and capacities of the vehicle. Overloading of the vehicle can overstress the components and cause failure. To prevent possible injury, it is equally important to follow the instructions and warnings that accompany the accessory.

  • Page 45: Environment

    Always keep a safe distance from other riders. Your judgment of speed, ter- rain conditions, weather, mechanical condition of your vehicle and the "trust in judgment" you have in others around you will help you make a better choice of appropriate safe distance.

  • Page 46: Off-Highway Operation

    Off-Highway Operation The very nature of off-highway operation is dangerous. Any terrain, which has not been specially prepared to carry vehicles, presents an inherent danger where angularity, terrain substance and exact steepness are unpredictable. The terrain itself presents a continual element of danger, which must be knowingly accepted by anyone venturing over it.

  • Page 47: Downhill Driving

    Downhill Driving This vehicle can climb slopes that are steeper than it can safely descend. There- fore, it is essential to assure that a safe route exists to descend a slope before you climb it. Decelerating while negotiating a slippery downhill slope could "toboggan" the ve- hicle.
  • Page 48 V00A0UL Even though there is an adequate suspensions system on this vehicle there are "washboard" or rough terrain conditions that will make you feel uncomfortable and even cause back injury. "Posting" or riding in a crouched position will often be required. Slow down and allow your flexed legs to absorb impact. If a road usage is allowed in your area, operate your vehicle on paved surface only for short distance and for the only purpose of moving the vehicle from an off- road usage to another.
  • Page 49 V00A0VL Water will affect the braking ability of your vehicle. Make sure you dry the brakes by applying them several times after the vehicle leaves the water. Mud or marsh lands may be encountered near water. Be prepared for sudden "holes"...
  • Page 50 When riding in sand dunes it is advisable to equip the vehicle with an antenna type safety flag. This will help make your location more visible to others over the next sand dune. Proceed carefully should you see another safety flag ahead. Since the antenna type safety flag can snag and rebound on your body if caught, do not use it in areas where there are low hanging branches or obstacles.
  • Page 51 Uphill Keep your body weight forward towards the top of the hill. Keep your feet on the footpegs and shift into low gear then accelerate and when necessary, change gear quickly as you climb. Do not over-speed since this may cause the front of the vehicle to lift from the ground and fall back on you.
  • Page 52 Downhill Keep your body weight rearwards. Apply the brake gradually to prevent skidding. Do not “coast” down the slope using solely engine compression or in neutral gear. V00A0YL While reading this Operator’s Guide, remember that: WARNING Indicates a potential hazard that, if not avoided, could result in serious in- jury or death.
  • Page 53 Side Hilling This is one of the most risky types of riding since it may drastically change the balance of the vehicle. It should be avoided wherever possible. If it is necessary to do so however, it is important that you ALWAYS keep your body weight on the upside of the slope...

  • Page 54: Routine Maintenance

    Part of your responsibility towards safety is to respect the contents of this Oper- ator's Guide. It provides valuable advice on how to properly take care of your ve- hicle. If further assistance is required your authorized Can-Am distributor/dealer is always willing to help.

  • Page 55: Hang Tag

    HANG TAG This vehicle comes with a hang tag and labels containing important safety infor- mation. Any person who rides this vehicle should read and understand this information before riding. V07M11L 704901107 vmo2006-005-009_en ____________ ___________ SAFETY INFORMATION...

  • Page 56: On-Product Labels

    The following labels are on your vehicle and they should be considered perma- nent parts of the vehicle. If missing or damaged, they can be replaced free of charge. See an authorized Can-Am distributor/dealer. NOTE: The following illustrations used in this Operator's Guide are a general representation only.
  • Page 57 Label 1 Label 3 V01M07Z Label 4 V01M01Z Label 2 vmo2006-007-002_aen Label 5 vmo2006-014-002_aen V01M02Z Label 6 V06M0EY ____________ ___________ SAFETY INFORMATION...
  • Page 58 Label 7 Label 9 vmo2006-005-012 Label 8 vmo2006-014-003_a 704 900 400 V01M0PY ___________ ___________ SAFETY INFORMATION...

  • Page 59: Vehicle Information

    VEHICLE INFORMATION _____________________...

  • Page 60: How To Identify Your Vehicle

    It may sometimes become necessary to locate these num- bers for warranty purposes or to trace your vehicle in the event of loss. These numbers are required by the authorized Can-Am distributor/dealer to complete warranty claims properly. No warranty will be allowed by BRP. if the engine iden- tification number (EIN) or vehicle identification number (VIN) is removed or mu- tilated in any way.
  • Page 61 Engine Identification Number Location vmo2006-014-005_a _____________________...

  • Page 62: Compliance Label

    Compliance Label This label indicates vehicle's compliance in many countries. LABEL LOCATION Right front lower tube of the frame (between A-arms) All DS 250 V00M03Y ______________________...

  • Page 63: Break-In Period

    (125 mi) or 30 days after the purchase, prolonged cruising speeds and engine whichever comes first, your vehicle overheating are detrimental during the be inspected by an authorized Can-Am break-in period. distributor/dealer. This inspection will give you the opportunity to discuss the...

  • Page 64: Controls/Instruments/Equipment

    CONTROLS/INSTRUMENTS/EQUIPMENT vmo2006-014-006_a ______________________...
  • Page 65 13-15 13-15 vmo2006-014-007_a _____________________...

  • Page 66: Throttle Lever

    While reading this Operator’s Guide, remember that: WARNING Indicates a potential hazard that, if not avoided, could result in serious in- jury or death. NOTE: This section gives basic func- tions of the various controls of your ve- hicle. For more details of how to op- erate one control in conjunction with some others, refer to OPERATING IN- STRUCTIONS further in this section.

  • Page 67: Parking Brake

    4) Parking Brake Located on right side of handlebar. When applied, it prevents the vehi- cle from moving. Useful when the brake needs to be locked for example such as doing a K-turn, during trans- portation or when the vehicle is not in operation.

  • Page 68: Multi-Function Switch

    R: Reverse Place switch to LO for the low beam and taillight, HI for the high beam and This allows the vehicle to go back- taillight and OFF to close the headlamp ward. This vehicle is equipped with and taillight. a reverse speed limiter system.
  • Page 69 Engine Start Button WARNING To start engine: depress and hold the Never activate the override but- engine start button, release immedi- ton if throttle lever is already de- ately after engine is started. pressed as loss of control may result, causing severe personal in- jury or death.

  • Page 70: Indicator Lamps

    High intensity (Blue) When this indicator light is on, it indicates HIGH BEAM is selected on the headlamps. Engine Temperature/Oil Pressure Lamp (red) This light turns when the ignition switch is turned remains until vmo2006-014-025 engine is running. When this TYPICAL —...

  • Page 71: Fuel Tank Cap

    WARNING Always stop engine before re- fueling. Open cap slowly. If a differential pressure condition is noticed (whistling sound heard when loosening fuel tank cap) have vehicle inspected and/or re- paired before further operation. Fuel is flammable and explosive under certain conditions. Never vmo2006-014-029_a use an open flame to check fuel TYPICAL...

  • Page 72: Front/Rear Brake Pedal

    11) Front/Rear Brake Pedal Located in front of the right footpeg. When pressed down, both front and rear brakes are applied. When re- leased, it should return to its original position. Braking effect is proportion- al to the force applied on the pedal and to the type and condition of the terrain.

  • Page 73: Radiator Cap

    The fuse holder is located in the ser- vice compartment underneath the seat. vmo2006-014-047_b 1. Tool kit 14) Radiator Cap vmo2006-014-047_a Located under front access cover. It 1. Fuse holder provides access to the radiator filling neck. 16) Vehicle Lock WARNING The vehicle lock is located on the steering stem directly below the steer-...

  • Page 74: Horn Button

    NOTE: _ As a safety precaution, or for theft prevention, lock the handlebar when parked. _ Once locked, turn handlebar on both sides to make sure it is properly locked. _ When leaving the vehicle, remember to remove the key. 17) Horn Button vmo2006-014-056_b 1.

  • Page 75: 12-Volt Power Outlet

    1. Seat latch wires are hidden in the wiring har- ness at the rear of vehicle. See an Seat Installation authorized Can-Am distributor/dealer Insert seat tab into frame hook. for more details. When seat rests in its position, firmly 21) Speedometer push seat down to latch.
  • Page 76 vmo2006-014-027_a 1. Speedometer 2. Odometer ______________________...

  • Page 77: Liquids

    LIQUIDS While reading this Operator’s Guide, remember that: WARNING Indicates a potential hazard that, if not avoided, could result in serious injury or death. NOTE: This section specifies the rec- Fuel Level ommended liquids and procedures to check their levels. Refer to MAINTE- WARNING NANCE for procedures to replace the Always stop engine before refu-...
  • Page 78 However during the hottest days of the summer the BRP XP-S 10W40 mineral oil (P/N 219 700 346) can be used. NOTE: For improved overall perfor- mance and all season application, use XP-S 5W40 synthetic oil (P/N 293 600 039). XP-S 5W40 Synthetic Oil (P/N 293 600 039) vmo2006-014-019_a...

  • Page 79: Gearbox Oil

    Do not mix with other types of oil. Gearbox Oil Level vmo2006-014-022_a authorized Can-Am COOLANT LEVEL distributor/dealer. With vehicle on a level surface, liquid should be between MIN. and MAX. Gearbox Oil Replacement level marks of coolant reservoir.

  • Page 80: Brake Fluid

    NOTE: A low level may indicate leaks lems. See an authorized Can-Am or worn brake pads. See an autho- distributor/dealer. rized Can-Am distributor/dealer. To gain access to the radiator, remove...

  • Page 81: Battery

    vmo2006-014-032 UNDERNEATH RH REAR FENDER Battery This vehicle is equipped with a dry type battery that requires no mainte- nance. NOTE: Refer to MAINTENANCE for removal and installation procedures. While reading this Operator’s Guide, remember that: WARNING Indicates a potential hazard that, if not avoided, could result in serious in- jury or death.

  • Page 82: Operating Instructions

    Correct any problem you may have al times to ensure it operates freely. found before riding. See an autho- It must return to idle position when rized Can-Am distributor/dealer as released. necessary. • Activate the brake levers and brake pedal to make sure the brakes fully Starting the Engine apply.

  • Page 83: Shifting The Transmission

    NOTE: Do not forget, place the engine Warm Engine Starting stop switch to RUN position and apply Start the engine as explained above brakes (front or rear). but without the choke. If the engine In cold weather, colder than 0°C does not start after two 5-second at- (32°F), place the choke lever to full tempts with the electric starter, move...

  • Page 84: Post-Operation Care

    Release throttle and completely stop the vehicle. Apply the parking brake. Set transmission lever in FORWARD position. Push the engine stop switch in OFF position. Turn key in ignition switch to OFF po- sition. Remove key from ignition switch. Post-Operation Care When vehicle is used in salt-water environment (beach area, launch-...

  • Page 85: Special Procedures

    Start engine as explained above. If en- gine continues to flood, see an autho- rized Can-Am distributor/dealer. NOTE: Make sure to verify that there is no fuel in engine oil, if so, replace engine oil.

  • Page 86: Turn Over

    Use the vehi- cle as little as possible and see an au- thorized Can-Am distributor/dealer as soon as possible. Turn Over When vehicle is turned over or stays...

  • Page 87: Cargo And Transportation

    CARGO AND TRANSPORTATION While reading this Operator’s Guide, remember that: WARNING Indicates a potential hazard that, if not avoided, could result in serious in- jury or death. Cargo WARNING If your vehicle is equipped to carry loads with optional racks and/or trail- er hitch approved by BRP, vehicle handling, stability and braking distance will be affected.
  • Page 88 CAUTION: Attaching vehicle at oth- er locations may damage the vehi- cle. Front Location vmo2006-014-063_a FRONT BUMPER STRAP LOCATIONS Rear Location vmo2006-014-064_a REAR BUMPER STRAP LOCATION WARNING Do not tow this vehicle behind a car or other vehicle. Use a trailer. ______________________...

  • Page 89: Troubleshooting

    – Start engine with spark plug grounded to the engine away from spark plug hole. If no spark appears, replace spark plug. – If trouble persists, contact an authorized Can-Am distributor/dealer. 5. Engine compression. – If no pulsating resistance is felt, it suggests a major loss of compression.
  • Page 90 – Contact an authorized Can-Am distributor/dealer. 4. Engine is overheating. – Check ENGINE OVERHEATING in SPECIAL PROCEDURES. – If overheating persists, contact an authorized Can-Am distributor/dealer. 5. Air filter/box plugged or dirty. – Check air filter and clean if necessary.
  • Page 91 UNUSUAL ENGINE NOISE 1. Valve adjustment. – Contact an authorized Can-Am distributor/dealer. 2. Chain tensioner plugged. – Contact an authorized Can-Am distributor/dealer. 3. Timing chain wear. – Contact an authorized Can-Am distributor/dealer. 4. CVT contamination – Contact an authorized Can-Am distributor/dealer.

  • Page 92: Specifications

    SPECIFICATIONS VEHICLE MODEL DS 250 ENGINE 4 stroke. Single overhead camshaft Type engine, liquid cooled. Number of cylinder Single cylinder 4 valves with mechanical lifters (adjustable) Number of valves Displacement 249.4 cc (15.22 cu. in) Bore 71 mm (2.8 in) Stroke 63 mm (2.5 in)
  • Page 93 VEHICLE MODEL DS 250 ELECTRICAL Magneto generator Type 338 W @ 5000 RPM Ignition type CDI (Capacitor Discharge Ignition) Ignition timing Not adjustable Make Spark plug Type CR8E 0.8 mm (.031 in) Number of spark plug Type Dry type battery...
  • Page 94 VEHICLE MODEL DS 250 WHEELS Front AT 10 x 5.5 Size Rear AT 9 x 8 Wheel nuts torque 50 N•m (37 lbf•ft) BRAKES Hydraulic, 2 discs Front Hydraulic, 1 disc Rear Parking device Separate RH lock lever on handlebar.
  • Page 95 VEHICLE MODEL DS 250 CAPACITIES 12.5 L (3.3 U.S. gal) Fuel tank 1.4 L (1.48 U.S. quarts) Engine Oil change: 1.2 L (1.27 U.S. quarts) Oil change: 800 mL (27 U.S. oz.) Gearbox oil 850 mL (28.7 U.S. quarts) Coolant...
  • Page 96 ______________________...

  • Page 97: Maintenance Information

    MAINTENANCE INFORMATION _____________________...

  • Page 98: Maintenance Chart

    Can-Am distributor/dealer. PERIODIC MAINTENANCE CHART INITIAL INSPECTION 10 H OR 30 DAYS OR 200 KM (125 mi) (To be performed by an authorized Can-Am dealer. The initial maintenance is very important and must not be neglected.) A: ADJUST...
  • Page 99 PERIODIC MAINTENANCE CHART INITIAL INSPECTION 10 H OR 30 DAYS OR 200 KM (125 mi) (To be performed by an authorized Can-Am dealer. The initial maintenance is very important and must not be neglected.) A: ADJUST C: CLEAN 25 H OR 500 KM (310 mi)
  • Page 100 PERIODIC MAINTENANCE CHART INITIAL INSPECTION 10 H OR 30 DAYS OR 200 KM (125 mi) (To be performed by an authorized Can-Am dealer. The initial maintenance is very important and must not be neglected.) A: ADJUST C: CLEAN 25 H OR 500 KM (310 mi)
  • Page 101 PERIODIC MAINTENANCE CHART INITIAL INSPECTION 10 H OR 30 DAYS OR 200 KM (125 mi) (To be performed by an authorized Can-Am dealer. The initial maintenance is very important and must not be neglected.) A: ADJUST C: CLEAN 25 H OR 500 KM (310 mi)

  • Page 102: General

    The following covers the maintenance items that can be performed by the cus- tomer if desired. Other items found in maintenance chart must be performed by an authorized Can-Am distributor/dealer. NOTE: Among other things, this section gives the procedures to replace the liq- uids.

  • Page 103: Engine

    ENGINE Oil Change and Oil Strainer Cleaning Oil change should be done with a warm engine. WARNING The engine oil can be very hot. In order to avoid potential burns, do not remove the engine drain plug or the oil strainer cover if the en- vmo2006-014-036_a gine is hot.

  • Page 104: Coolant Replacement

    Clean washer area on engine and drain Unplug the by-pass hose on the top of plug then reinstall plug and torque it to thermostat housing. 39 N•m (29 lbf•ft). Refill engine at the proper level with the recommended oil. Refer to SPEC- IFICATIONS for capacity.

  • Page 105: Air Filter Housing Draining

    Check the level in the coolant reservoir CAUTION: Do not start engine and refill if necessary. when liquid/deposits are found in the drain tube. Run engine at idle with the radiator cap off. Slowly add additional coolant When liquid/deposits found, if necessary.

  • Page 106: Drive Belt

    Valve Adjustment authorized Can-Am distributor/dealer valves justment. Insufficient clearance will cause loss of power and possibly damage the valves. Excessive clearance will cause noise. Radiator Periodically check the radiator area for vmo2006-014-046_a cleanliness. 1. Clamp 2. Retaining screw Inspect radiating fins. They must be...

  • Page 107: Air Injection Valve Filter Cleaning

    Air Injection Valve Filter When finished, properly reinstall re- moved parts in the reverse order of Cleaning their removal. vmo2006-014-066_b LH SIDE OF ENGINE 1. Air injection valve Disconnect hoses from air injection valve. Remove air injection valve from its support.

  • Page 108: Gearbox

    GEARBOX Oil Change Refill gearbox, using (27 U.S. oz) of XP-S chaincase oil Place the vehicle on a level surface. (P/N 413 801 900) or an equivalent. Remove the drive chain protector. NOTE: Gearbox oil quantity is also written on the gearbox cover. CAUTION: Do not use other unrec- ommended types of oil when ser- vicing.

  • Page 109: Carburetor

    CARBURETOR authorized Can-Am distributor/dealer each year to verify and clean the fuel system. _____________________...

  • Page 110: Fuel System

    FUEL SYSTEM Throttle Cable Lubrication The throttle cable must be lubricated with silicone cable lubricant (P/N 293 600 041) or an equivalent. WARNING Always use a silicone-based lu- bricant. Using another lubricant (like water-based lubricant) could cause the throttle lever/cable stick- ing or stiffness.

  • Page 111: Throttle Lever Adjustment

    Throttle Lever Adjustment Slide rubber protector back to expose throttle cable adjuster. Loosen lock nut then turn the adjuster to obtain correct throttle lever free play. NOTE: Measure throttle free play at the tip of throttle lever. Tighten lock nut and reinstall protector. vmo2006-014-052_a 1.

  • Page 112: Electrical

    ELECTRICAL Apply anti-seize lubricant over spark WARNING plug threads to prevent a possible Unless otherwise informed, al- seizure. ways turn ignition switch to the Screw spark plug into cylinder head by OFF position before performing hand and tighten with a torque wrench any maintenance or repair on elec- and a proper socket.

  • Page 113: Fuse

    WARNING Connect RED (+) cable first then BLACK (-) cable. Always connect RED (+) cable first. Fuse If fuses are damaged, replace them by one of the same rating. CAUTION: Do not use a higher rat- ed fuse as this can cause severe A15E0KY damage.
  • Page 114 vmo2006-014-058_a vmo2006-014-057_a 1. Headlamp housing 2. Beam height adjustment 1. Remove rubber protector 2. Pull on connector using a wiggle movement Taillight Unlock bulb holder by turning it coun- Unscrew lens screws to expose bulb. terclockwise. Replace bulb. V06G0UY TYPICAL vmo2006-014-057_b 1.
  • Page 115 Remove lamp lens. vmo2006-014-071 vmo2006-014-068_a PULL ON BULB HOUSING TO REMOVE PULL ON LENS TO REMOVE Rear Direction Indicator Lamps 1. Lamp lens Unscrew housing cover screws and Push bulb in and hold while turning lower housing retaining screws. counterclockwise to release. Install the new bulb by first pushing in while turning clockwise.
  • Page 116 vmo2006-014-070_a 1. Bulb housing _____________________...

  • Page 117: Drive Train

    DRIVE TRAIN Drive Chain Select a level surface and set trans- mission to NEUTRAL. Adjust and lubricate drive chain before each use. Loosen chain tensioner lock bolts and caliper support bolt. WARNING Place ignition switch to the OFF po- sition before checking, adjusting or lubricating the drive chain.

  • Page 118: Sprocket And Pinion

    V06H06Y Tighten the chain tensioner lock bolts to 50 N•m (37 lbf•ft). CAUTION: Never operate this vehi- cle with the drive chain too loose or vmo2006-014-060_a 1. Sprocket hub holes too tight as severe damage to the 2. Chain tensioner drive components can occur.

  • Page 119: Wheel

    26 kPa (3.8 PSI) Push and pull the wheels from the upper edge to feel the play. See an authorized Can-Am distributor/dealer if Although the tires are specifically de- there is any play. signed for off-road use, a flat may still occur.
  • Page 120 V06H05Y TYPICAL 1. Taper side of nut CAUTION: Always use the recom- mended wheel nuts. Using a differ- ent nut could cause damages to the rim. _____________________...

  • Page 121: Suspension

    A. Same length on both sides LH SIDE OF VEHICLE 1. CVT duct 2. Grease fitting Inspection Front and Rear Suspension Inspect shock absorbers for oil leaks and fasteners for tightness. See an authorized Can-Am distributor/dealer as necessary. _____________________...
  • Page 122 Swing Arm Check swing arm for distortion, cracks or bending. See an autho- rized Can-Am distributor/dealer if any problem is detected. A-Arms Check A-arms for cracks, bending or other damages. See an authorized Can-Am distributor/dealer as neces- sary. _____________________...

  • Page 123: Brake

    Any brake system repair should between cable adjuster and caliper be performed by an authorized piston. Can-Am distributor/dealer. Tighten lock nut and verify that parking brake is working properly. Front Brake The front brakes are hydraulic disc types.

  • Page 124: Inspection

    2 mm (.079 in) Brake discs thickness 2 mm (.079 in) Maximum discs 0.15 mm warpage (.010 in) Brake Fluid Replacement WARNING The brake fluid replacement or any brake system repairs should be performed by an authorized Can-Am distributor/dealer. _____________________...

  • Page 125: Body/Frame

    BODY/FRAME Engine Area CAUTION: Never clean plastic parts with strong detergent, degreasing Check engine area for any damage agent, paint thinner, acetone, etc. and leaks. Ensure all hose clamps are properly secured and no hose is cracked, kinked or otherwise dam- aged.

  • Page 126: Storage And Preseason Preparation

    When a vehicle is not in use for more than one month, proper storage is a necessity. authorized Can-Am distributor/dealer proper pro- cedures. When using your vehicle after storage, a preparation is required. See an au- thorized Can-Am distributor/dealer for proper procedures. _____________________...

  • Page 127: Warranty

    WARRANTY _____________________...

  • Page 128: Brp International Limited Warranty: 2007 Can-Am Atv

    Can-Am distributor/dealer. Moreover, this warranty coverage is only available if the Can-Am ATV is purchased in the country in which the purchaser resides. BRP will not honor this limited warranty to any private use owner or commercial use owner if the preceding conditions have not been met.
  • Page 129 BRP’s obligations under this warranty are limited to, at its sole discretion, repair- ing parts found defective under normal use, maintenance and service; or replac- ing such parts with new genuine Can-Am ATV parts without charge for parts and labour, at any authorized Can-Am distributor/dealer.
  • Page 130 If the ownership of a product is transferred during the warranty coverage period, this warranty shall also be transferred and be valid for the remaining coverage period provided BRP or an authorized Can-Am distributor/dealer receives a proof that the former owner agreed to the transfer of ownership, in addition to the coordinates of the new owner.
  • Page 131 If the matter still remains unresolved then contact BRP by writing to us at the address listed below. BRP EUROPE N.V.. CAN-AM ATV CONSUMER SERVICE CENTER BELGIUM Tel : +32 (0) 9 272 63 30 ©...

  • Page 132: Privacy Obligation/Disclaimer

    PRIVACY OBLIGATION/DISCLAIMER We wish to inform you that your coordinates will be used for safety and warranty purposes. Sometimes, we also use the coordinates of our clients to inform them about our products and to present them offers. Should you prefer not to receive information on our product, services and offers, please let us know by writing to the address below.

  • Page 133: Change Of Address/Ownership

    It is the owner’s responsibility to notify BRP. STOLEN UNITS: If your personal ATV is stolen, you should notify BRP or an au- thorized Can-Am dealer. We will ask you to provide your name, address, phone number, the vehicle identification number and the date it was stolen.
  • Page 134 _____________________...
  • Page 135 ATV MODEL No. VEHICLE IDENTIFICATION NUMBER (V.I.N.) ENGINE IDENTIFICATION NUMBER (E.I.N.) Owner: NAME STREET CITY STATE/PROVINCE ZIP/POSTAL CODE Purchase Date YEAR MONTH Warranty Expiry Date YEAR MONTH To be completed by the dealer at the time of the sale. DEALER IMPRINT AREA V00A2IL Please verify with your dealer to ensure your vehicle has been registered with BRP.
  • Page 136 WARNING THIS VEHICLE CAN BE HAZARDOUS TO OPERATE. A collision or rollover can occur quickly, even during routine manoeuvers such as turning and driving on hills or over obstacles, if you fail to take proper precautions. SEVERE INJURY OR DEATH can result if you do not follow these instructions: •...

Table of Contents