Care And Cleaning - American Standard Cadet PRO Series Installation Instructions Care And Maintenance

8
A
Adjust water level to level
indicated on tank by turning
water level adjustment knob
to move float cup up or down.
B

CARE AND CLEANING

When cleaning your toilet, wash it with mild, soapy water, rinse thoroughly with clear water and dry with a soft cloth.
WARNING: Do not use in-tank cleaners. These products can seriously corrode fittings in the tank. This damage can cause leakage and property damage.
American Standard shall not be responsible or liable for any damage caused by the use of in-tank cleaners.
Problem Possible Cause
Does not flush a. Water supply valve closed.
b. Supply line blocked.
c. Flush valve chain too loose or disconnected.
d. Sand or debris lodged in water control.
Poor or a. Bowl water level too low.
sluggish flush
b. Supply valve partly closed.
c. Partially clogged trapway and/or drain pipe and/or vent.
d. Supply pressure too low.
Toilet leaks a. Poor supply line connection.
b. Poor bowl to tank/floor connection.
Toilet does not a. Flapper seal leaking or deformed.
shut off b. Sand or debris lodged in water control.
c. Flush valve chain too tight, holding flapper open.
Toilet bowl a. Wax ring not fully compressed.
rocks after b. Floor not level.
installation
In the United States:
American Standard Brands
1 Centennial Ave
Piscataway, New Jersey 08854
Attention: Director of Customer Care
For residents of the United States, warranty
information may also be obtained by calling
the following toll free number: (800) 442-1902
www.americanstandard.com
Fill Valve
Or Water
TROUBLESHOOTING GUIDE - See Step 8 For Diagram
Corrective Action
a. Open valve and allow water to fill tank.
b. Shut off water supply, disconnect supply line and inspect all gaskets and washers. Reassemble.
c. Readjust chain length as required.
d. Shut off water supply. Remove cap and clean as per Fluidmaster maintenance instructions at:
a. Check that refill tube is connected to water control and inserted into overflow tube without being
b. Open supply valve fully. Be sure that proper supply tube size is used.
c. Remove obstruction. Consult a plumber if necessary.
d. Normal supply pressure must be at least 20 psi.
a. Review Step 7 of installation procedure.
b. Review Step 1 through 6 of installation procedure.
a. Clean debris from seal surface. Replace flapper seal as needed. See web for more info.
b. Shut off water supply. Remove cap and clean as per Fluidmaster maintenance instructions at:
c. Readjust chain length as needed.
a. Retighten bowl-to-floor knobs.
b. Use toilet shims and /or place a bead of caulk around the base of the toilet.
LIXIL Canada, ULC
5900 Avebury Rd.
Mississauga, Ontario
Canada L5R 3M3
Toll Free: (800) 387-0369
www.americanstandard.ca
Water Level
Adjustment Knob
Float Cup
Control
Flapper
Flapper
Water Supply Line
www.americanstandard-us.com/enews/fluidmasterguide.pdf
kinked or damaged.
www.americanstandard-us.com/enews/fluidmasterguide.pdf
In Canada:
- 4 -
Trip Lever Rod
Approximate
Water Level
Flush Valve
Chain
Overflow
Tube
Seal
Tank to Bowl Gasket
In Mexico:
American Standard B&K Mexico
S. de R.L. de C.V.
Via Morelos #330
Col. Santa Clara
Ecatepec 55540 Edo. Mexico
Toll Free: 01-800-839-1200
www.americanstandard.com.mx
7301878-100 Rev. 4 8/19
Refill Tube
Flush
Valve