Campbell Hausfeld PW2575 Product Manual page 7

Lavadoras a Presión
Mantenimiento (Continuación)
Plan de Mantenimiento
Plan de Mantenimiento Acción Necesaria
• Revisar la pantalla y el filtro
Diariamente
de entrada de agua.
• Revisar los niveles de aceite
del motor. Llenar según sea
necesario.
• Revisar el nivel de gasolina.
Llenar según sea necesario.
Después de las • Cambiar el aceite de ablande
primeras 5 horas de del motor. Usar aceite
funcionamiento detergente SAE30 o 10W-30.
Cada 25 horas de • Cambiar el aceite si funciona
funcionamiento con carga pesada o a una
temperatura ambiente alta.
• Limpie o reemplace el
cartucho de papel del filtro de
aire. Golpee suavemente para
quitar la suciedad.
Cada 50 horas de • Cambiar el aceite
funcionamiento • Reemplazar la bujía
• Reemplace el cartucho de
Cada 100 horas de
funcionamiento o papel del filtro de aire.
cada 3 meses • Cambiar el aceite del motor
Registro de Servicio y Mantenimiento
Fecha Mantenimiento efectuado
Información Técnica y Para el Consumidor
Lavadoras a Presión de Orientación Vertical
Tipo de aceite para el motor SAE 10W-30
SAE 30W
(Por encima de 15˚ C)
Capacidad de aceite para el motor
Motores Honda 0,55 L
Capacidad de combustible para el motor
Motores Honda 1,10 L
Tipo de aceite para la bomba
Bombas oscilantes SAE20W o SAE30W
aceite no detergente
Capacidad de aceite para la bomba
Bombas oscilantes verticales 0,12 L
Succión de detergente de la bomba
Proporción de agua a detergente 8 a 1
(12% detergente)
Requisitos del abastecimiento de agua
Presión mínima de entrada 1,38 bar
Presión máxima de entrada 6,90 bar
Temperatura máxima de entrada 38˚ C
Velocidad mínima de flujo de entrada 19 Lpm
Tamaño de la manguera de entrada 15,9 mm (5/8 inch)
diámetro interior
Largo máximo de la manguera
de entrada 15,24 m (50 pies)
Reemplazo necesario de componentes
26 Sp
Pressure Washers
Operation (Continued)
4. Detergent Application
USE THE INSTRUCTIONS APPROPRIATE
FOR MODEL PURCHASED
NOTE: Use only detergents formulated
for pressure washers.Test detergent in an
inconspicuous area before use.
Never slide the
nozzle from low to
high pressure or from high to low
pressure when the gun is triggered.
DETERGENTS
The use of detergents can dramatically
reduce cleaning time and assist in the
removal of difficult stains. Many
detergents are customized for pressure
Figure 15 - Adjusting nozzle for pressure
washer use on specific cleaning tasks.
Pressure washer detergents are as thick
The lance will extend 1/2" and be in
as water. Using thicker detergents –
low pressure (see Figure 15). Soap
like dish soap – will clog the chemical
can only be drawn in low pressure.
injection system and prevent the
B. MODELS WITHOUT DETERGENT TANKS
application of the detergent.
1. Follow manufacturer's label
Once applied to a cleaning surface,
detergents take time to break down dirt directions for mixing correct
concentrations of soap/detergents.
and grime. Detergents work best when
applied at low pressure. The soap detergent to water ration
through the pump is approximately
You can effectively clean surfaces by
12% (1 to 8).
combining the chemical action of
detergents with high pressure rinses. On
2. Insert the filter end of the clear
vertical surfaces, apply the detergent
plastic detergent tube into the
starting at the bottom and work your
detergent container.
way upward. This method prevents the
3. Place hand around the spraying end
detergent from sliding down and causing
section of the lance (the section that
streaks. Begin high pressure rinsing at the
turns from left to right). Pull firmly
bottom and work your way upward. On
and quickly away from you. (NOTE:
particularly tough stains, use a brush in
Do not adjust lance while spraying.)
combination with detergents and high
The lance will extend 1/2" and be in
pressure rinsing.
low pressure (see Figure 15). Soap
Gasoline Powered Units
can only be drawn in low pressure.
Equipped with Adjusting Nozzle
GENERAL CLEANING TIPS
A. MODELS WITH DETERGENT TANKS 1. Apply the detergent so that it
thoroughly covers the cleaning
1. Follow manufacturer's label
surface. Apply the detergent from
directions for mixing correct
bottom to top to prevent the
concentrations of soap/detergents.
detergent from sliding down and
The soap detergent to water ratio
streaking. Wait a couple of minutes
through the pump is approximately
for the detergent to break down the
12% (1 to 8).
dirt and grime. Use a brush to lightly
2. Pour detergent into the detergent
scrub heavily soiled areas. Never allow
tank. The tank capacity is 1.5 gallons.
the detergent to dry on the cleaning
3. Place hand around the spraying end
surface.
section of the lance (the section that
2. To rinse or to return the nozzle to
turns from left to right). Pull firmly
high pressure, release the trigger and
and quickly away from you. (NOTE:
slide the nozzle to the high pressure
Do not adjust lance while spraying.)
setting.
www.chpower.com
Low Pressure
Nozzle
High Pressure
Never make the
nozzle pressure
adjustment with the gun triggered.
Adjusting the high-low nozzle when the
gun is triggered can result in damage to
the seals in the nozzle.
3. After using detergents, flush the
suction system by placing the
detergent suction tube into a bucket
of clean water or rinse out tank.
5. Cleaning Power
You can control the cleaning power of
your pressure washer in two ways:
1. Adjust the spray pattern at the
nozzle. Choose the widest pattern
possible for spraying when starting
the job and adjust the pattern to a
narrower angle until you find a
suitable pattern.
2. The easiest way to regulate the
cleaning power of your pressure
washer is by changing the distance
from the surface you are cleaning.
Begin spraying with a wide fan
pattern while standing several feet
from the surface. Slowly move closer
to the object you are cleaning,
adjusting the spray pattern as
necessary, until you find the most
effective cleaning technique.
6. Final Rinse
The final rinse should start at the
bottom and work upward. Make sure
that you thoroughly rinse the surface
and that you remove all detergent.
7