Table of Contents
Advertisement
Before beginning installation, carefully read these instructions. This will simplify the installation and ensure the dryer
is installed correctly and safely. Leave these instructions near the Dryer after installation for future reference.
NOTE: The electrical service to the Dryer must conform with local codes and ordinances and the latest edition of the
National Electrical Code, ANSI/NFPA 70 or in Canada, CSA C22.1 Canadian Electrical Code Part 1.
NOTE: The gas service to the Dryer must conform with local codes and ordinances and the latest edition of the
National Fuel Gas Code ANSI Z223.1 or in Canada, CAN/CGA B149.12.
NOTE: The Dryer is designed under ANSI Z 21.5.1 or ANSI/UL 2158 - CAN/CSA C22.2 (latest editions) for HOME USE only.
This Dryer is not recommended for commercial applications such as restaurants or beauty salons, etc.
For your safety the information in
this manual must be followed to minimize the risk
of fire or explosion or to prevent property damage,
personal injury or loss of life.
- Do not store or use gasoline or other flammable
vapors and liquid in the vicinity of this or any other
appliance.
- WHAT TO DO IF YOU SMELL GAS
· Do not try to light any appliance.
· Do not touch any electrical switch; do not use
any phone in your building.
· Clear the room, building or area of all
occupants.
· Immediately call your gas supplier from a
neighbor's phone. Follow the gas supplier's
instructions.
· If you cannot reach your gas supplier, call the
fire department.
Installations must be performed by a qualified or
licensed contractor, plumber, or gasfitter qualified
or licensed by the state, province, or region where
this appliance is being installed.
Printed in U.S.A.
Installation
Instructions
Contents
SUBJECT
Gas & Electric
Dryer
PAGE
2
2
2-3
3
4
5
5-6
6
6
7
7
8
8
9
9
P/N 134296400 (0308)
Advertisement
Table of Contents
Related Manuals for Frigidaire GLGR341AS4
Summary of Contents for Frigidaire GLGR341AS4
-
Page 1: Table Of Contents
National Fuel Gas Code ANSI Z223.1 or in Canada, CAN/CGA B149.12. NOTE: The Dryer is designed under ANSI Z 21.5.1 or ANSI/UL 2158 - CAN/CSA C22.2 (latest editions) for HOME USE only. This Dryer is not recommended for commercial applications such as restaurants or beauty salons, etc. -
Page 2: Pre-Installation Requirements
MUST be installed downstream with the flow of air. where gasoline or other flammables are kept or stored. If the dryer is installed in a garage, it must be a minimum of 18 inches (45.7 cm) above the floor. Failure to do so can result in death, explosion, fire or burns. -
Page 3: Gas Supply Requirements
16 ft. (4.87 m) However, on electric dryers, exhausting can be to the right or left side of the cabinet or the bottom of the dryer. On gas dryers, exhausting can be to the right side of the cabinet or the bottom of the dryer. -
Page 4: Location Of Your Dryer
CLOSET DOOR 0" (0 cm) If an under counter* installation is desired, the dryer MUST have a top sheet kit installed, P/N 131629100. Kit is available from an authorized parts distributor. 4. A minimum of 120 square inches (774.2 square cm) of opening, equally divided at the top and bottom of the door, is required. -
Page 5: Mobile Home Installation
3. When installing a gas dryer into a mobile home, a provision must be made for outside make up air. This provision is to be not less than twice the area of the dryer exhaust outlet. -
Page 6: Rough-In Dimensions
(68.6 cm) SIDE VIEW 1. Using the four shipping carton corner posts (two on each side), carefully lay the dryer on its left side and remove foam shipping base. as a means to pick up or move the dryer. NOTE: On under counter model clothes dryers, the top panel may be removed for installation. -
Page 7: Electrical Installation
A U.L. approved strain relief must be installed onto power cord. If the strain relief is not attached, the cord can be pulled out of the dryer and can be cut by any movement of the cord, resulting in electrical shock. -
Page 8: Electrical Connections-3-Wire
5. Attach the green power cord ground wire to the cabinet with the green ground screw. 6. Attach the white (neutral) power cord conductor from the power cord and the green ground wire from the dryer harness to the silver-colored center terminal on the terminal block. Tighten the screw securely. -
Page 9: Installation
2. Connect the exhaust duct to outside exhaust system. Use duct tape to seal all joints. 3. With the dryer in its final position, adjust one or more of the legs until the dryer is resting solid on all four legs. Place a level on top of the dryer.