Advertisement
Available languages
Available languages
9.7 PLASMA ION OPERATION
Capture effi ciency of fl oating impurities in the air is accelerated by plasma ion
contaminates such as bacteria, odor, smoke, dust and virus are caught and
deactivated by Plasma Ion.
1. Press MENU button for enter menu setting and press TEMP. button to
select PURE
MENU
MEN
2. Confi rm selected feature by press MENU button again.
MENU
MEN
3. Leave from menu setting display by select EXIT.
MENU
MEN
Note:
● Plasma Ion operation dose not remove harmful substances from cigarette
smoke (carbon monoxide etc.). Open a window occasionally for ventilation.
9.8 POWER-SELECTION OPERATION
This function is used when the circuit breaker is shared with other electrical
appliances. It limits the maximum current and power consumption to 100%,
75%, or 50% and can be implemented by POWER-SELECTION. The lower
percentage, the higher saving and also longer compressor lifetime.
Notes :
● Due to the reason that POWER-SELECTION function limits the maximum
current, inadequate cooling or heating capacity may occur.
1. Press MENU button for enter menu setting and press TEMP. button to select
POWER-SEL
MEN
MENU
2. Enter POWER-SEL setting by press MENU button again.
MEN
MENU
3. Select POWER-SEL level by press TEMP. button.
100%
75%
4. Confi rm POWER-SEL level by press MENU button.
MEN
MENU
PURE
Blink both triangle and
°C
feature mark Feature not
yet set
°C
Blink only triangle Feature
already set
°C
°C
Blink only triangle
°C
°C
50%
°C
5. Leave from menu setting display by select EXIT.
MEN
MENU
MANUAL DEFORST OPERATION
10
To defrosting the heat exchanger of the outdoor unit during Heating operation
Press and hold
MENU
MEN
show
as picture 1 for 2 seconds.
DISPLAY LAMP BRIGHTNESS ADJUSTMENT
11
To decrease the display lamp brightness or turn it off.
FAN
FAN
1. Press and hold
or
) is shown on remote control LCD then release the button.
2. Press
or
Rise
Decrease
Remote control
LCD
Lamp illuminates full brightness.
Lamp illuminates 50% brightness.
Lamp illuminates 50% brightness and the
operation lamp is turned off.
All lamps are turned off.
● In the examples of
and
, the lamp illuminates for 5 seconds before going off.
AUTO RESTART FUNCTION SETTING
12
This product is designed so that, after a power failure, it can restart automatically
in the same operating mode as before the power failure.
Information
The product was shipped with Auto Restart function in the OFF position.
Turn it ON as required.
How to turn ON the Auto Restart Function
● Press and hold the [OPERATION] button on the indoor unit for 3 seconds
(3 beep sounds and OPERATION lamp blink 5 time/sec for 5 seconds).
How to turn OFF the Auto Restart Function
● Press and hold the [OPERATION] button on the indoor unit for 3 seconds
(3 beep sounds but OPERATION lamp does not blink).
Notes :
● In case of ON timer or OFF timer are set, AUTO RESTART OPERATION
does not activate.
SELF CLEANING OPERATION
13
(COOL AND DRY OPERATION ONLY)
To protect bad smell caused by the humidity in the indoor unit.
1. If the
button is pressed once during "Cool" or "Dry" mode,
the fan will continue to run for other 30 minutes, then it will turn off
automatically. This will reduce the moisture in the indoor unit.
2. To stop the unit immediately, press the
seconds.
°C
: for 5 seconds , then remote control display will
1
for 3 seconds until brightness level (
to adjust brightness in 4 levels.
Operation display
more 2 times within 30
,
,
Brightness
100%
50%
50%
All turned off
Advertisement
