Self Cleaning Operation; Operation And Performance - Toshiba RAS-M10J2FVG-TR Owner's Manual

FLOOR WARMING OPERATION
7
Heating will operate with downward blowing only.
Temperature of air outlet will be higher than usual.
Press : Start and stop the operation.
Note: FLOOR operation can active in Heat mode only.
8 ECO OPERATION
To automatically control room temperature to save energy (except in DRY
mode).
Press : Start and stop the operation.
Note: Cooling operation; the internal set temperature will increase
automatically 1 degree by 2 hours (maximum 2 degrees increase).
For heating operation the internal set temperature will decrease.
9 TIMER OPERATION
Set the timer when the air conditioner is operating.
Setting the ON Timer
1
Press : Set the desired
ON timer.
2
Press : Set the timer.
3
Press : Cancel the timer.
Note:
• Keep the remote control in accessible transmission to the indoor unit;
otherwise, the time lag of up to 15 minutes will occur.
• The setting will be saved for the next same operation.
• Press to cancel the daily timer operation.
10 PRESET OPERATION
Set your preferred operation for future use. The setting will be memorized by
the unit for future operation (except airflow direction).
1. Select your preferred operation.
2. Press and hold
3. Press : Operate the preset operation.
11 FIREPLACE AND 8°C HEATING OPERATION
Fireplace Operation (
Keep indoor unit's fan blowing continuously during thermo off, to circulate heat
from other sources over the room. There are three setting parameters: Default
setting > Fireplace 1 > Fireplace 2
Fireplace 1:
During thermo off period, the indoor unit's fan will continue to run by the same
speed, previously selected by end-user.
Fireplace 2:
During thermo off period, the indoor unit's fan will continue to run at super-low
speed, programmed from factory.
8°C Heating Operation (8°C)
Heat mode operation for keep room temperature (5-13°C) with less of energy
usage.
Fireplace and 8°C Heating Operation
FIREPLACE 1
Note:
• While Fireplace operation on heating mode, indoor unit fan always runs
and cold air breezing might be occurred.
• Fireplace and 8°C will operate in Heating mode only.
1112150136-00_S01_182x257_16p_S_p70_190923.indd 5
Setting the OFF Timer
Press : Set the desired
OFF timer.
Press : Set the timer.
Press : Cancel the timer.
until stop blinking and the mark displays.
)
8°C
FIREPLACE 2
Normal
operation
12 COMFORT SLEEP OPERATION
For comfortable sleep, automatically control air flow and automatically turn
OFF (Except in DRY mode).
1. Press : Select 1, 3, 5 or 9 hrs for OFF timer operation.
2. Press to cancel the comfort sleep operation.
Note: The cooling operation, the set temperature will increase automatically
1 degree/hour for 2 hours (maximum 2 degrees increase). For heating
operation, the set temperature will decrease.
AUTO RESTART FUNCTION SETTING
13
This product is designed so that, after a power failure, it can restart
automatically in the same operating mode as before the power failure.
Information
The product was shipped with Auto Restart function in the OFF position.
Turn it ON as required.
How to turn ON the Auto Restart Function
• Press and hold the [OPERATION] button on the indoor unit for 3 seconds
(3 Beep sounds and OPERATION lamp blink 5 time/sec for 5 seconds).
How to turn OFF the Auto Restart Function
• Press and hold the [OPERATION] button on the indoor unit for 3 seconds
(3 Beep sounds but OPERATION lamp does not blink).
Note: In case of ON timer or OFF timer are set, AUTO RESTART
OPERATION does not activate.
14 FILTER RESET
Firstly, turn off the circuit breaker.
FILTER lamp lights on; the filter must be cleaned.
To turn off the lamp, push OPERATION button on the indoor unit or the
FILTER button on the remote control.
Note: The filter indicator turns on after about 1000 hours.
Indoor Unit and Remote Control
• Clean the indoor unit and the remote control with a wet cloth when needed.
• No benzine, thinner, polishing powder or chemically-treated duster.

SELF CLEANING OPERATION

15
(COOL AND DRY OPERATION ONLY)
Cleaning operation
This function is used to dry the inside of the air conditioner to reduce the
growth of mold, etc. inside the air conditioner.
• When the unit shuts down after having operated for 10 or more
minutes in the cooling or dry mode, the cleaning operation is started
automatically, and the TIMER indicator on the unit's display panel turns
on.
Cleaning operation duration
• The cleaning operation lasts for 30 minutes if the unit has been operating
in the cooling or dry mode for 10 minutes or more.
Note:
• SELF CLEANING operation is default setting from factory.
• How to cancel SELF CLEANING operation.
Press and hold MODE button on operation panel for more than 10
seconds (less than 20 seconds). When canceling, 4 beeps sound.
• How to activate SELE CLEANING operation.
Press and hold MODE button on operation panel for more than 10
seconds (less than 20 seconds). Then, 4 beeps will sound and operation
lamp will blink for 5 seconds.
16

OPERATION AND PERFORMANCE

1. Three-minute protection feature: To prevent the unit from being activated
for 3 minutes when suddenly restarted or switched to ON.
2. Preheating operation: Warm up the unit for 5 minutes before blowing warm
air.
3. Warm air control: When the room temperature reaches the set
temperature, the fan speed is automatically reduced and the outdoor unit
will stop.
4. Automatic defrosting: Fans will stop during defrost operation.
5. Heating capacity: heat is absorbed from outdoor and released into the
room.
When the outdoor temperature is too low, use another recommended
heating apparatus in combination with the air conditioner.
6. Consideration for accumulated snow: Select the position for outdoor unit
where it will not be subjected to snow drifts, accumulation of leaves or
other seasonal debris.
7. Some minor cracking sound may occur when unit operating. This is normal
because the cracking sound may be caused by expansion/contraction of
plastic.
EN
1/24/2020 2:58:39 PM