National Instruments R Series User Manual
For usb multifunction rio with kintex-7 160t fpga
Hide thumbs
Also See for R Series:
- User manual (72 pages) ,
- Getting started manual (12 pages) ,
- User manual (10 pages)
Table of Contents
Advertisement
Quick Links
USER MANUAL
NI USB-7846R OEM
R Series for USB Multifunction RIO with Kintex-7 160T FPGA
Français
This document provides dimensions, connectivity information, and pinouts for the National
Instruments USB-7846R OEM device.
Caution
compatibility (EMC), or CE marking compliance claims for NI USB-7846R OEM
device. The end-product supplier is responsible for conformity to any and all
compliance requirements.
Caution
in this user manual. Product misuse can result in a hazard. You can compromise the
safety protection built into the product if the product is damaged in any way. If the
product is damaged, return it to National Instruments for repair.
Hardware Overview
The following high-level block diagram represents the NI USB-7846R OEM device.
Deutsch
ni.com/manuals
National Instruments makes no product safety, electromagnetic
Do not operate the NI USB-7846R OEM device in a manner not specified
한국어
日本語
简体中文
Advertisement
Table of Contents
Related Manuals for National Instruments R Series
Summary of Contents for National Instruments R Series
- Page 1 USER MANUAL NI USB-7846R OEM R Series for USB Multifunction RIO with Kintex-7 160T FPGA 한국어 日本語 Français Deutsch 简体中文 ni.com/manuals This document provides dimensions, connectivity information, and pinouts for the National Instruments USB-7846R OEM device. Caution National Instruments makes no product safety, electromagnetic compatibility (EMC), or CE marking compliance claims for NI USB-7846R OEM device.
- Page 2 Figure 1. NI USB-7846R OEM Device Block Diagram DIO (x16) 40 MHz Flash Overvoltage Memory Protection DIO (x16) Overvoltage Protection DIO (x16) Overvoltage AI (x8) Protection Kintex-7 NI ASIC Data/ FPGA Address/ Control +5 V FPGA Overvoltage Temperature Reference Protection AO (x8) Overvoltage Protection...
-
Page 3: Parts Locator
C&K (E101J1AQE2) The following table lists and describes the I/O connectors on the NI USB-7846R OEM device. Refer to the connector manufacturer for information about using and matching these connectors. NI USB-7846R OEM User Manual | © National Instruments | 3... - Page 4 Table 2. NI USB-7846R OEM Device Connectors Connector Description Reference Designator Manufacturer AI, AO 50-position header 3M (N2550-6002RB) 34-position header 3M (N2534-6002RB) External LED 7-position header FCI 68000-107LF 4 | ni.com | NI USB-7846R OEM User Manual...
- Page 5 Dimensions 2X 6.675 (169.55) 2X 6.435 (163.46) 6.263 (159.08) 2X 6.055 (153.81) 2X 2.863 (72.72) 2X .175 (4.45) .000 (0) .119 (3.02) NI USB-7846R OEM User Manual | © National Instruments | 5...
- Page 6 3.812 (96.82) 6.500 (165.1) 2.688 (68.28) 5.830 (148.08) Note Visit for more information about the dimensions of ni.com/dimensions the NI USB-7846R OEM device, including two-dimensional drawings and three- dimensional models. Note The NI USB-7846R OEM device has plated mounting holes that can act as chassis ground.
-
Page 7: Analog Input
Figure 3. Figure 3. Connecting Referenced Single-Ended Signals to the NI USB-7846R OEM Device Overvoltage Protection PGIA AI– Overvoltage Protection – AISENSE Overvoltage Protection AIGND NI USB-7846R OEM NI USB-7846R OEM User Manual | © National Instruments | 7... -
Page 8: Connecting Differential Voltage Signals
To connect non-referenced single-ended voltage signals to the NI USB-7846R OEM device, you must connect the voltage ground signal to AI SENSE in order to keep the common-mode voltage in the specified range, as shown in Figure 4. Figure 4. Connecting Non-Referenced Single-Ended Signals to the NI USB-7846R OEM Device Overvoltage Protection... -
Page 9: Analog Output
10 MHz signal frequencies. Each connector has selectable logic levels that you can configure as 1.2 V, 1.5 V, 1.8 V, 2.5 V, or 3.3 V. You can configure each channel as input or output. NI USB-7846R OEM User Manual | © National Instruments | 9... - Page 10 The VI can then set the DIO lines to any power-on state. National Instruments recommends performing signal integrity measurements to test the effect of signal routing with the cable and connection accessory for your application.
- Page 11 V) and 3 and the negative connection. To connect the remaining LEDs, refer to Table 3. National Instruments recommends that you limit the current to 10 mA per LED. You can limit this current by using external resistors, as shown in Figure 9.
-
Page 12: Power Switch
Power Switch Use the power switch to power the NI USB-7846R OEM device on and off. The following figure shows the pins on the power switch and power circuitry. Figure 11. Power Switch (Shown in the On Position) 100 kΩ VDC Out VDC In to Ground... -
Page 13: Autonomous Mode
Doing so can damage the device and the computer. National Instruments is not liable for damage resulting from such a connection. The power rating is 4.75 to 5.1 VDC at 0.5 A. Autonomous Mode You can run the NI USB-7846R OEM device without a USB connection to a host computer using Autonomous Mode. -
Page 14: Worldwide Support And Services
Other product and company names mentioned herein are trademarks or trade names of their respective companies. For patents covering National Instruments products/technology, refer to the appropriate location: Help»Patents in your software, the file on your media, or the National Instruments Patent Notice at .