Table of Contents
Advertisement
Quick Links
GETTING STARTED GUIDE
NI PXIe-7822R
R Series for PXI Express Digital RIO with Kintex-7 325T FPGA
Français
This document explains how to install and configure the NI PXIe-7822R.
Safety Guidelines
Caution
manual. Product misuse can result in a hazard. You can compromise the safety
protection built into the product if the product is damaged in any way. If the product
is damaged, return it to National Instruments for repair.
Electromagnetic Compatibility Guidelines
This product was tested and complies with the regulatory requirements and limits for
electromagnetic compatibility (EMC) as stated in the product specifications. These
Deutsch
ni.com/manuals
Do not operate the NI PXIe-7822R in a manner not specified in this user
한국어
日本語
简体中文
Advertisement
Table of Contents
Related Manuals for National Instruments PXIe-7822
Summary of Contents for National Instruments PXIe-7822
- Page 1 Product misuse can result in a hazard. You can compromise the safety protection built into the product if the product is damaged in any way. If the product is damaged, return it to National Instruments for repair. Electromagnetic Compatibility Guidelines This product was tested and complies with the regulatory requirements and limits for electromagnetic compatibility (EMC) as stated in the product specifications.
-
Page 2: Unpacking The Kit
requirements and limits are designed to provide reasonable protection against harmful interference when the product is operated in its intended operational electromagnetic environment. This product is intended for use in residential, commercial, and industrial locations. However, harmful interference may occur in some installations or when the product is connected to a peripheral device or a test object. -
Page 3: Preparing The Environment
NI-RIO Device Drivers February 2015 or later LabVIEW Real Time Module is only required if the R Series board is being used on a PXIe controller with a real-time operating system. NI PXIe-7822R Getting Started Guide | © National Instruments | 3... - Page 4 Visit ni.com/info and enter the Info Code for minimum software support softwareversion information. Installing the NI PXIe-7822R Caution To prevent damage to the device caused by ESD or contamination, handle the device using the edges or the metal bracket. Ensure the AC power source is connected to the chassis before installing the modules. The AC power cord grounds the chassis and protects it from electrical damage while you install the modules.
- Page 5 If the device does not appear, press <F5> to refresh the view in MAX. If the device does not appear after refreshing the view, visit for troubleshooting ni.com/support information. NI PXIe-7822R Getting Started Guide | © National Instruments | 5...
- Page 6 Verifying Hardware Installation for Remote Targets You can verify that the system recognizes the NI PXIe-7822R by using Measurement & Automation Explorer (MAX). Launch MAX on the host computer. Expand Remote Targets in the configuration tree and locate your system. Install LabVIEW Real-Time Module 2014 SP1 and NI RIO Device Drivers February 2015 or later on your Remote Target.
- Page 7 External Clock x is an input only. The NI PXIe-7822R is protected from overvoltage and overcurrent conditions. Refer to the NI PXIe-7822R Specifications, available at , for more information on ni.com/manuals overvoltage and overcurrent conditions. NI PXIe-7822R Getting Started Guide | © National Instruments | 7...
-
Page 8: Installing Noise Suppression Ferrites
Digital I/O The NI PXIe-7822R provides connections for 128 digital input/output (DIO) channels. Connectors 0 through 3 each contain 32 high-speed DIO channels that can run up to 80 MHz signal frequencies. Each connector has selectable logic levels that you can configure as 1.2 V, 1.5 V, 1.8 V, 2.5 V, or 3.3 V. - Page 9 Shielded R Series High Speed Digital Cable, 2m (156166-02) For user-supplied cables, the ferrite beads can be ordered directly from NI by visiting ni.com/ info and entering RDIO2FERRITE Figure 5. Ferrite Installation 1. I/O cable 2. Ferrites NI PXIe-7822R Getting Started Guide | © National Instruments | 9...
-
Page 10: Where To Go Next
NI Application Engineers. National Instruments corporate headquarters is located at 11500 North Mopac Expressway, Austin, Texas, 78759-3504. National Instruments also has offices located around the world to help address your support needs. For telephone support in the United States, create your service request at ni.com/support... - Page 11 Other product and company names mentioned herein are trademarks or trade names of their respective companies. For patents covering National Instruments products/technology, refer to the appropriate location: Help»Patents in your software, the file on your media, or the National Instruments Patent Notice at .