Fostex VM88 Owner's Manual page 29

Doubling effect parameters (parameter type: DOUBLING)
For effect type 34 of the preceding "Effect type" table, the following three parameters can be adjusted.
1. Lch DELAY TIME
2. Rch DELAY TIME
3. FILTER
Chorus effect parameters (parameter type: CHORUS)
For effect type 35 of the preceding "Effect type" table, the following four parameters can be adjusted.
1. DEPTH
2. DOUBLING TIME
3. DOUBLING BALANCE
4. FILTER
Flanger effect parameters (parameter type: FLANGE)
For effect type 36 of the preceding "Effect type" table, the following four parameters can be adjusted.
1. RATE
2. DEPTH
3. MOD DELAY
4. FEEDBACK
Mono pitch effect parameters (parameter type: MONO PITCH)
For effect type 37 of the preceding "Effect type" table, the following three parameters can be adjusted.
1. PITCH
2. ADJUST
3. MODE
Delay pitch effect parameters (parameter type: DELAY PITCH)
For effect type 38 of the preceding "Effect type" table, the following four parameters can be adjusted.
1. PITCH
2. ADJUST
3. DLY TIME
4. FEEDBACK
Adjust the delay time of the L channel. Range: 0.1--9.9 ms (99 steps in 0.1 ms units), 10-
-99 ms (90 steps in 1 ms units), 100--200 ms (51 steps in 2 ms units)
* The ENTER key / foot switch cannot be used for tap input.
Adjust the delay time of the R channel. Range: 0.1--9.9 ms (99 steps in 0.1 ms units), 10-
-99ms (90 steps in 1 ms units), 100--200 ms (51 steps in 2 ms units)
* The ENTER key / foot switch cannot be used for tap input.
Adjust the tone of the delay sound. Range: L9~L1, -, H1~H9
* [-] is Filter Off
* L1~L9 = LPF (larger numbers will lower the cutoff frequency)
* H1~H9 = HPF (larger numbers will raise the cutoff frequency)
Adjust the chorus depth. Range: 0--99 (100 steps in increments of 1)
Adjust the time difference of the doubling effect. Range: 0--99 (100 steps in increments
of 1)
Adjust the volume of the doubling effect. Range: 0--99 (100 steps in increments of 1)
Adjust the tone of the delay sound. Range: L9~L1, -, H1~H9
* [-] is Filter Off
* L1~L9 = LPF (larger numbers will lower the cutoff frequency)
* H1~H9 = HPF (larger numbers will raise the cutoff frequency)
Adjust the speed of modulation. Range: 0.1--2.0 Hz (200 steps in 0.01 Hz units)
Adjust the depth of modulation. Range: 0--99 (100 steps in increments of 1)
Adjust the modulation delay. Range: 0--200 (201 steps in increments of 1)
Adjust the number of modulation repeats. Range: 0--99 (100 steps in increments of 1)
Adjust the amount of pitch shift. Range: -24--0--+24 (49 steps in semitone units)
* +/-12 is one octave. +/-24 is two octaves.
Make fine adjustments to the amount of pitch shift. Range: -50--0--+50 (101 steps in
increments of 1)
* +50 is a semitone sharp. -50 is a semitone flat.
Select the processing method. Range: 1--3 (3 steps)
Adjust the amount of pitch shift. Range: -24--0--+24 (49 steps in semitone units)
* +/-12 is one octave. +/-24 is two octaves.
Make fine adjustments to the amount of pitch shift. Range: -50--0--+50 (101 steps in
increments of 1)
* +50 is a semitone sharp. -50 is a semitone flat.
Adjust the delay time until the pitch-shifted sound is heard. Range: 0--500 ms (251 steps
in increments of 2)
* The ENTER key / foot switch can be used for tap input (refer to page 27).
Adjust the number of delay repeats. Range: 0--99 (100 steps in increments of 1)
Model VM88 Owner's Manual
29