Page 2
FORTINET DOCUMENT LIBRARY https://docs.fortinet.com FORTINET VIDEO GUIDE https://video.fortinet.com FORTINET BLOG https://blog.fortinet.com CUSTOMER SERVICE & SUPPORT https://support.fortinet.com FORTINET TRAINING & CERTIFICATION PROGRAM https://www.fortinet.com/support-and-training/training.html NSE INSTITUTE https://training.fortinet.com FORTIGUARD CENTER https://fortiguard.com/ END USER LICENSE AGREEMENT https://www.fortinet.com/doc/legal/EULA.pdf FEEDBACK techdoc@fortinet.com Email: October 25, 2019 FIM-7901E 5.6.11 Build 4279 Processing Module Guide...
Industry Canada Equipment Standard for Digital Equipment (ICES) – Canada European Conformity (CE) - EU Voluntary Control Council for Interference (VCCI) – Japan Bureau of Standards Metrology and Inspection (BSMI) – Taiwan China FIM-7901E Processing Module Guide Fortinet Technologies Inc.
When both module levers are fully closed, the power sliders can be lowered to their bottom position, locking the module levers and turning on power to the module. FIM-7901E Processing Module Guide Fortinet Technologies Inc.
SFP transceivers. These interfaces also support creating link aggregation groups (LAGs) that can include interfaces from both FIM-7901Es. M1 and M2 SFP+ 10Gbps/1Gbps Ethernet Two front panel 10GigE SFP+ interfaces that FIM-7901E Processing Module Guide Fortinet Technologies Inc.
Max Current 37.5A Heat Dissipation 1531BTU/h Joules/h 1609KJ/h Front panel LEDs From the FIM-7901E font panel you can view the status of the module LEDs to verify that the module is functioning normally. FIM-7901E Processing Module Guide Fortinet Technologies Inc.
Connection at 1Gbps. MGMT1-4 Amber Connection at 100Mbps. Speed Connection at 10Mbps. Supported transceivers Transceivers available from Fortinet for the FIM-7901E A1 to A32 SFP+ interfaces. Transceiver Description FG-TRAN-SFP+SR 10GE SFP+ transceiver module, short range. FG-TRAN-SFP+LR 10GE SFP+ transceiver module, long range.
NMI switch When working with Fortinet Support to troubleshoot problems with the FIM-7901E you can use the front panel non- maskable interrupt (NMI) switch to assist with troubleshooting. Pressing this switch causes the software to dump registers/backtraces to the console. After the data is dumped the FIM-7901E reboots. While the FIM-7901E is rebooting, traffic is temporarily blocked.
If the transceiver does not easily slide in and click into place, it may not be aligned correctly. If this happens, remove the transceiver, realign it and slide it in again. FIM-7901E Processing Module Guide Fortinet Technologies Inc.
FIM module from a chassis slot. FIM-7901E mounting hardware Power Slider Alignment Pin Alignment Pin Module Lever Power Slider Secure Screw Secure Screw Module Lever Open Closed (to open move the power slider up about 2 mm) FIM-7901E Processing Module Guide Fortinet Technologies Inc.
This procedure describes how to insert a FIM-7901E module into slot 1 or 2 of a FortiGate-7000 chassis. The procedure includes photographs to illustrate the procedure steps. The photos were taken in one of Fortinet's hardware labs using a generic module and FortiGate-7000 chassis.
Page 14
Before sliding the final portion of the module into the chassis fully open both levers by pushing the power sliders up. Fully open both levers to avoid damaging the lever mechanism. Damaging the levers can prevent the module from connecting to power. Power slider Power slider Levers pop open FIM-7901E Processing Module Guide Fortinet Technologies Inc.
Page 15
The design of the levers leaves gaps to compensate for tolerances. So even when the levers are fully closed, the module may not be fully into position and in contact with the chassis backplane. Small gap between the module and the chassis when levers are closed. Rotate to close Levers closed FIM-7901E Processing Module Guide Fortinet Technologies Inc.
Page 16
Tighten by hand After tightening both secure screws, the module is fully engaged with the chassis. Fully tighten with a screwdriver FIM-7901E Processing Module Guide Fortinet Technologies Inc.
This procedure describes how to shut down and remove a FIM-7901E module from FortiGate-7000 chassis. The procedure includes photographs to illustrate the procedure steps. The photos were taken in one of Fortinet's hardware labs using a generic module and FortiGate-7000 chassis.
Page 18
To shutdown the module, connect to the module GUI Shutdown from the administrator menu. Or, from the module CLI, enter the execute shutdown and select command. 2. Disconnect all cables from the module, including all network cables and USB cables or keys. FIM-7901E Processing Module Guide Fortinet Technologies Inc.
Page 19
Do not use a power screwdriver, because the high torque and speed can damage the chassis or screw thread. Use a Phillips screwdriver to loosen both screws. Fully loosen both screws by hand. FIM-7901E Processing Module Guide Fortinet Technologies Inc.
Page 20
4. Unlock the left and right levers by pushing the power sliders up until the levers pop open. Push the power sliders up to fully open both levers. If the chassis is powered on, this step turns off the module’s power. Power slider Power slider Levers pop open FIM-7901E Processing Module Guide Fortinet Technologies Inc.
Page 21
Module ejected Levers opened 6. Hold the levers to slide the module part way out of the chassis slot. Then grasp the module by the sides and carefully slide it out of the slot. FIM-7901E Processing Module Guide Fortinet Technologies Inc.
To resolve the problem you can try removing and reinserting the FIM-7901E in the chassis slot. Reloading the firmware may also help. If this does not solve the problem there may have been a hardware failure or other problem. Contact Fortinet Technical Support for assistance.
Registering your FortiGate-7000 series products FortiGate-7000 series products are registered according to the chassis serial number. You need to register your chassis to receive Fortinet customer services such as product updates and customer support. You must also register your https://support.fortinet.com product for FortiGuard services.
Page 24
Connect to the GUI by connecting MGMT1 of the module in slot 1 to your network and browsing to https://192.168.1.99. Log into the GUI using the admin account with no password. Go to Network > Interface and configure the FIM-7901E interfaces to connect to your network. FIM-7901E Processing Module Guide Fortinet Technologies Inc.
être accordée aux connexions d'alimentation autres que les connexions directes au circuit de dérivation (par exemple de l'utilisation de bandes de puissance). Equipment must be used only with UL Listed ITE or Equivalent. L'équipement doit être utilisé uniquement avec UL ITE ou équivalent. FIM-7901E Processing Module Guide Fortinet Technologies Inc.
Fiber optic transceiver must be rated 3.3V, 22mA max, Laser Class 1, UL certified component. Le transceiver optique doit avoir les valeurs nominales de 3.3 V, maximum 22 mA, Laser Class 1, homologué UL FIM-7901E Processing Module Guide Fortinet Technologies Inc.
European Conformity (CE) - EU This is a Class A product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. FIM-7901E Processing Module Guide Fortinet Technologies Inc.