Advertisement
Locate the Reed Switch (10) and the Magnet (18) on
the left side of the Pulley (17). Turn the Pulley until the
Magnet is aligned with the Reed Switch. Make sure
that the gap between the Magnet and the Reed
Switch is about 3 mm (1/8 in.). If necessary, loosen
the Screw (26) and move the Reed Switch slightly.
Retighten the Screw. Re-attach the Hood (not shown),
and run the treadmill for a few minutes to check for a
correct speed reading.
PROBLEM: The walking belt slows when walked on
SOLUTION: a. If an extension cord is needed, use only a 3-conductor, 1mm
than 1.5 m (5 ft.).
b. If the walking belt is overtightened, treadmill perfor-
mance may decrease and the walking belt may be-
come damaged. Remove the key and UNPLUG THE
POWER CORD. Using the hex key, turn both rear
roller adjustment bolts counterclockwise, 1/4 of a turn.
When the walking belt is properly tightened, you
should be able to lift each side of the walking belt
8–10cm (3-4 in.) off the walking platform. Be careful to
keep the walking belt centred. Plug in the power cord,
insert the key, and run the treadmill for a few minutes.
Repeat until the walking belt is properly tightened.
c. If the walking belt still slows when walked on, call our Customer Service Department.
PROBLEM: The walking belt is off-centre or slips when walked on
SOLUTION: a. If the walking belt is off-centre, remove the key and
UNPLUG THE POWER CORD. If the walking belt
has shifted to the left, use the hex key to turn the left
rear roller bolt clockwise 1/2 of a turn; if the walking
belt has shifted to the right, turn the left rear roller
bolt counterclockwise 1/2 of a turn. Be careful not to
overtighten the walking belt. Plug in the power cord,
insert the key, and run the treadmill for a few minutes.
Repeat until the walking belt is centred.
b. If the walking belt slips when walked on, first remove
the key and UNPLUG THE POWER CORD. Using
the hex key, turn both rear roller bolts clockwise, 1/4
of a turn. When the walking belt is correctly tightened,
you should be able to lift each side of the walking belt
8–10cm (3–4 in.) off the walking platform. Be careful
to keep the walking belt centred. Plug in the power
cord, insert the key, and walk on the treadmill for a
few minutes. Repeat until the walking belt is properly
tightened.
3 mm
17
10
26
18
Top
View
2
(14-gauge) cord that is no longer
b
8–10 cm
Rear Roller Adjustment Bolts
a
b
16
BEFORE YOU BEGIN
Congratulations for selecting the new PROFORM
®
P treadmill. The 360 P treadmill combines advanced
technology with innovative design to help you get the
most from your exercise in the convenience and pri-
vacy of your home. And when you're not exercising, the
unique 360 P treadmill can be folded up, requiring less
than half the floor space of other treadmills.
For your benefit, read this manual carefully before
using the treadmill. If you have questions after read-
Water Bottle Holder
(Bottle not included)
Handrail
Storage Latch
Walking Belt
Foot Rail
BACK
Rear Roller
Adjustment Bolts
360
ing this manual, please call our Customer Service
Department at 08457 089 009. To help us assist you,
please note the product model number and serial num-
ber before calling. The model number of the treadmill
is PETL3013.7. The serial number can be found on a
decal attached to the treadmill (see the front cover of
this manual for the location).
Before reading further, please familiarise yourself with
the parts that are labelled in the drawing below.
Bookrack
Console
Key/Clip
Upright
On/Off Switch
Circuit Breaker
RIGHT SIDE
Cushioned Walking Platform
for maximum exercise comfort
5
Advertisement
