Advertisement
ASSEMBLY
Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials. Do not
dispose of the packing materials until assembly is completed. Note: The underside of the treadmill walking belt is
coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to the
top of the walking belt or the shipping carton. This is a normal condition and does not affect treadmill perfor-
mance. If there is lubricant on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild,
non-abrasive cleaner.
Assembly requires the included hex keys
and your own phillips screwdriver
wire cutters
, needlenose pliers
For help identifying the assembly hardware, refer to the PART IDENTIFICATION CHART in the centre of
this manual. Note: The assembly hardware and other small parts are packaged in separate part bags. Do
not open the part bags until instructed to do so.
1. Make sure that the power cord is unplugged.
With the help of a second person, carefully tip the tread-
mill onto its left side as shown. Partially fold the Frame
(86) so that the treadmill will be more stable. Do not fully
fold the treadmill until it is completely assembled.
Open part bag A. Attach the two Base Pads (57) and
two Base Endcaps (65) to the bottom of the Base (69)
with four 1" Tek Screws (58). Attach a Wheel (66) to the
Base with a 2" Bolt (64) and a Nut (13).
Note: It may be helpful to tap on the Base Endcaps with
a rubber mallet as you insert the Base Endcaps.
2. Identify the Right and Left Uprights (29, 25); the Left
Upright has two small holes in the indicated location.
Make sure that there are two U-nuts (45) in the lower
end of each Upright (see drawing 2a).
Hold the Right Upright (29) near the Base (69), and orient
the Right Upright so the indicated bracket is in the
position shown. Straighten the Wire Harness (42), and
feed it into the lower end of the Right Upright and out of
the upper end. Make sure that no wires are pinched.
Hand tighten two 3" Bolts (70) with Star Washers (63)
into the bottom of the Base and the lower end of the
Right Upright.
With the help of a second person, tip the treadmill onto
its other side. Attach the Left Upright (25) as described
above. (Note: There is not a wire harness on the left
side.) Attach the other Wheel (not shown) to the Base
(69) as described in step 1.
,
, and rubber mallet
.
1
86
64
65
58
57
58
13
69
65
58
57
58
2
Bracket
69
29
63
Holes
70
42
2a
29, 25
45
6
TROUBLESHOOTING
Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and
follow the steps listed. If further assistance is needed, please call our Customer Service Department.
PROBLEM: The power does not turn on
SOLUTION: a. Make sure that the power cord is plugged into a properly earthed outlet. (See page 9.) If an exten-
sion cord is needed, use only a 3-conductor, 1 mm
(5 ft.). Important: The treadmill is not compatible with GFCI-equipped outlets.
b. After the power cord has been plugged in, make sure that the key is fully inserted into the console.
c. Check the circuit breaker located on the treadmill
near the power cord. If the switch protrudes as
shown, the circuit breaker has tripped. To reset the
circuit breaker, wait for five minutes and then press
the switch back in.
d. Check the on/off switch located on the treadmill
near the power cord. The switch must be in the on
position.
66
PROBLEM: The power turns off during use
SOLUTION: a. Check the circuit breaker located on the treadmill near the power cord (see c. above). If the cir-
cuit breaker has tripped, wait for five minutes and then press the switch back in.
b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for
five minutes, and then plug it back in.
c. Remove the key from the console. Reinsert the key fully into the console.
d. Make sure that the on/off switch is in the on position (see d. above).
e. If the treadmill still will not run, please call our Customer Service Department.
PROBLEM: The displays of the console do not function properly
SOLUTION: a. Remove the key from the console and UNPLUG THE
POWER CORD. Remove the four 3/4" Screws (61)
from the Hood (1), and carefully pivot the Hood off.
25
2
(14-gauge) cord that is no longer than 1.5 m
c
Tripped
Reset
d
On
Position
a
61
1
15
Advertisement
