Page 1
MX-G71R SERVICE MANUAL COMPACT COMPONENT SYSTEM MX-G71R Area Suffix U.K. Continental Europe Northern Europe Eastern Europe STANDBY/ON STANDBY PLAY & EXCHANGE CD-R / RW PLAYBACK MX-G71R SP-MXG71R CA-MXG71R SP-MXG71R Contents Safety precautions Flow of functional operation Important for laser products...
Page 2
MX-G71R 1. This design of this product contains special hardware and many circuits and components specially for safety purposes. For continued protection, no changes should be made to the original design unless authorized in writing by the manufacturer. Replacement parts must be identical to those used in the original circuits. Services should be performed by qualified personnel only.
Page 3
MX-G71R (U.K only) 1. This design of this product contains special hardware and many circuits and components specially for safety purposes. For continued protection, no changes should be made to the original design unless authorized in writing by the manufacturer.
Page 4
MX-G71R Important for laser products 5.CAUTION : If safety switches malfunction, the laser is able 1.CLASS 1 LASER PRODUCT to function. 2.DANGER : Invisible laser radiation when open and inter 6.CAUTION : Use of controls, adjustments or performance of lock failed or defeated. Avoid direct exposure to beam.
Page 5
MX-G71R Preventing static electricity 1. Grounding to prevent damage by static electricity Electrostatic discharge (ESD), which occurs when static electricity stored in the body, fabric, etc. is discharged, can destroy the laser diode in the traverse unit (optical pickup). Take care to prevent this when performing repairs.
Page 6
MX-G71R Disassembly method Metal cover <Main body> Removing the metal cover (See Fig.1 to 3) Remove the six screws A on the back of the body. Remove the two screws B on both sides of the body. Remove the metal cover from the body by lifting the rear part of the cover.
Page 7
MX-G71R Removing the CD changer mechanism Front panel assembly assembly (See Fig.4 and 5) Prior to performing the following procedure, remove the metal cover. Disconnect the card wire from connector CN661 on the Main board. Remove the two screws C on the upper side of the body and the two screws D on the back of the rear panel.
Page 8
MX-G71R Remove the four screws E on the bottom of the Front panel assembly body. Release the two joints a on the lower right and left sides of the body using a screwdriver, and remove the front panel assembly toward the front.
Page 9
MX-G71R Removing the tuner board Plastic rivet Tuner board (See Fig.11 and 12) Prior to performing the following procedure, remove Rear panel the metal cover and the CD changer mechanism assembly. Disconnect the card wire from connector CN1 on the tuner board on the right side of the body.
Page 10
MX-G71R Removing the main board Main board (See Fig.16 and 17) CN870 Front panel assembly Prior to performing the following procedure, remove CN871 CN315 the metal cover, the CD changer mechanism assembly, the rear panel and the tuner board. Amplifier board...
Page 11
MX-G71R Removing the power cord / power supply Tie band Voltage board board (See Fig.19) Prior to performing the following procedure, remove Power supply board the metal cover, the CD changer mechanism assembly and the rear panel. Power Disconnect the wire from connector CN250 on the cord power supply board.
Page 12
MX-G71R Removing power transformer assembly (See Fig.22 and 23) Tie band Voltage board Power transformer Prior to performing the following procedure, remove assembly the metal cover, the CD changer mechanism assembly and the rear panel. Remove the tie band attaching the wire to the voltage board.
Page 13
MX-G71R Head amplifier <Front panel assembly> & Mechanism control board CN306 Prior to performing the following procedure, remove the metal cover, the CD changer mechanism assembly and the front panel assembly. Removing cassette mechanism assembly (See Fig.24) Disconnect the card wire from connector CN306 on the head amplifier &...
Page 14
MX-G71R Removing the preset / tuning switch Preset / tuning switch board board (See Fig.29 and 30) Prior to performing the following procedure, remove the display system control board. Pull out the preset knob on the front panel. Remove the five screws Q attaching the preset / tuning switch board.
Page 15
MX-G71R Removing the CD Servo control board (See Fig.1) 1.Remove the metal cover. 2.Remove the CD changer mechanism assembly. 3.From bottom side the CD changer mechanism assembly, remove the four screws A retaining the CD servo control CN854 board. 4.Absorb the four soldered positions "a" of the right and left motors with a soldering absorber.
Page 16
MX-G71R Stopper Check whether the lifter unit stopper has been caught into the hole at the section "e" of CD tray assembly as shown in Fig.5. Make sure that the driver unit elevator is positioned as shown in Fig.6 from to the second or fifth hole on the left side face of the CD changer mechanism assembly.
Page 17
MX-G71R Cams R1, R2 assembly Removing the CD loading mechanism assembly (See Fig.10) While turning the cams R1 and R2 assembly in the arrow direction "h" ,align the shaft "i" of the CD loading mechanism assembly to the position shown in Fig.10.
Page 18
MX-G71R Removing the try select switch board Chassis assembly (See Fig.14) Remove the two screws G retaining the tray select switch board. Tray select switch board Disconnect the tray select switch board from connector CN804 on the CD servo control board.
Page 19
MX-G71R Removing the actuator motor and belt Gear bracket (See Fig.18~21) Remove the two screws I retaining the gear bracket (See Fig.18). While pressing the pawl "t" fixing the gear bracket in the arrow direction, remove the gear bracket Pulley gear (See Fig.18).
Page 20
MX-G71R Slit washer Removing the cams R1/R2 assembly and cam gear q (See Fig.22) Cam R2 Slit washer Remove the slit washer fixing the cams R1 and R2 assembly. Cam gear q By removing the two pawls "w" fixing the cam R1, separate R2 from R1.
Page 21
MX-G71R < Cassette mechanism section > Cassette mechanism Removing the playback,recording and eraser heads (See Fig.1~3) 1. While shifting the trigger arms seen on the right side of the head mount in the arrow direction,turn Flywheel R the flywheel R in counterclockwise direction until the head mount has gone out with a click (See Fig.
Page 22
MX-G71R Removing the head amp. and mechanism control board (See Fig. 4) 1.Remove the cassette mechanism assembly. Head amplifier & 2.After turning over the cassette mechanism mechanism control board assembly,remove the five screws "A" retaining the head amplifier & mechanism control board.
Page 23
MX-G71R Removing the capstan motor (See Fig. 8) Capstan motor From the joint bracket, remove the two screws "C" retaining the capstan motor. Joint bracket Removing the flywheel (See Fig. 9 and 10) 1.Remove the head amp. and mechanism control P.C.Board.
Page 24
MX-G71R < Speaker section > Attention which adheres to speaker box The speaker box of this model is a unit supply. Therefore, we do not supply it as individual parts though the method of disassembling the speaker box has been described.
Page 25
MX-G71R Tweeter speaker Fig.4 Removing the woofer speaker (See Fig.5) Prior to performing the following procedure, remove the side cover and the front cover. Remove the four screws E on the front of the body. Pull out the woofer speaker toward the front and disconnect the wire (yellow and black,blue and black) from the two speaker terminals.
Page 26
MX-G71R Adjustment method Measurement instruments required for adjustment Radio input signal 1. Low frequency oscillator, AM modulation frequency : 400Hz This oscillator should have a capacity to output 0dBs Modulation factor : 30% to 600ohm at an oscillation frequency of 50Hz-20kHz.
Page 27
MX-G71R Arrangement of adjusting positions Cassette mechanism section (Mechanism A section) Cassette mechanism section (Back side) Head azimuth Head azimuth adjusting screw adjusting screw (Reverse side) (Forward side) Head azimuth Head azimuth Playback, recording and eraser adjusting screw adjusting screw...
Page 28
MX-G71R Tape recorder section Adjusting Items Measurement Standard Measurement method positions conditions values Confirmation Adjust the head Test tape Maximum 1.Playback the test tape TMT7036(10kHz). of head angle azimuth screw :TMT7036(10kHz) output 2.With the playback mechanism or recording & only when the...
Page 29
MX-G71R Electrical performance Adjusting Items Measurement Standard Measurement method positions conditions values Adjustment of AC-225 *Mode : Forward or 1.With the recording and playback mechanism, recording bias :4.20 A reverse mode load the test tapes(AC-225 to TYP ),and set the...
Page 30
MX-G71R Flow of functional operation until TOC read Check Point Slider turns REST Play Key Power ON Confirm that the voltage at the pin5 SW ON. of CN801 is "H"\"L"\"H". Automatic tuning of TE offset Check that the voltage at the...
Page 31
MX-G71R Replacement of laser pickup Maintenance of laser pickup (1) Cleaning the pick up lens Before you replace the pick up, please try to Turn off the power switch and, disconnect the clean the lens with a alcohol soaked cotton power cord from the ac outlet.
Page 32
MX-G71R Description of major ICs AN7345(IC302) : PB/REC AMP 1. Block diagram NF1 OUT1 CTL1 RIN1 RNF1 ROUT1 REPPLE Source CTRL CTRL OUT2 EQ2 CTL2 RIN2 RNF2 ROUT2 2. Pin Function Symbol Function Symbol Function Power supply Playback amplifier input...
Page 34
MX-G71R BA3835S (IC812) : SPI B.P.F. 1.Block Diagrams BIASC BIAS AOUT VREFC VREF REFERENCE RREF TEST CURRENT N.C. N.C. PEAK 105Hz HOLD N.C. N.C. PEAK 340Hz HOLD PEAK 1kHz DIFOUT HOLD PEAK 3.4kHz HOLD PEAK 10.5kHz HOLD 2.Pin Function Symbol Function Decoupling condenser connection terminal.
Page 35
MX-G71R BU2092/F(IC811):PORT EXPANDER 1.Terminal Layout DATA CLOCK CONTROL CIRCUIT 2.Pin Function Pin No. Symbol Function Connect to GND DATA Serial Data input CLOCK Shift Clock of Data Latch Clock of Data 5~16 Q0~Q11 Parallel Data Output Latch Data OUTPUT ON OFF...
Page 36
MX-G71R LA1838(IC1): FM AM IF AMP&detector, FM MPX decoder 1. Block Diagram DECODER RF.AMP ANIT-BIRDIE MUTE BUFF STEREO P-DET AM IF PILOT 384KHz COMP S-METER AM/FM S-CLRVE S-METER IF-BUFF TUNING STEREO DRIVE DRIVE FM IF 2. Pin Function Symbol Function...
Page 37
MX-G71R LA6541-X (IC801) : Servo driver 1. Pin Layout & block diagram Vref Vin4 Vin3 Level B T L B T L Level RESET shift driver driver shift Level B T L B T L Level Regulator shift driver driver...
Page 40
MX-G71R MN101C35OEC2 (IC810) : System controller Pin function (1/2) Symbol Function Pin No. VC3 Serial data output KCMND VC3 status input MSTAT VC3 Serial clock KCLK SLC/TUNER data output DATAOUT TUNER data input DATAIN SLC/TUNER clock Not used Power supply +5V...
Page 41
MX-G71R Pin function (2/2) Symbol Function Pin No. FL segment control signal output 64~85 P22~P1 Tuner chip enable TUCE System mute SMUTE Skip LED SEARCH LE LED Control signal output (CD1) CD1 LED LED Control signal output (CD2) CD2 LED...
Page 42
MX-G71R MN662748RPM (IC651) : Digital servo & digital signal processor 1. Pin layout 20 ~ 41 ~ 2.Block diagram LRCKIN(MSEL) 8TIMES BCLK(SSEL) DIGITAL OVER SAMPLING OUTR SRDATAIN DE-EMPHSIS 1bit DIGITAL FILTER (PSEL) IOSEL LOGIC CLVS BLKCK OUTL CLDCK SBCK SUBC...
Page 43
MX-G71R 3. Pin function Dymbol I/O Function Symbol I/O Function Tracking error shunt signal output (H:shunt) BCLK Not used PLLF2 Not used LRCK TOFS Not used SRDATA WVEL Not used Not used DVDD1 Power supply (Digital) RF signal input DVSS1...
Page 46
MX-G71R VICTOR COMPANY OF JAPAN, LIMITED AUDIO & COMMUNICATION BUSINESS DIVISION PERSONAL & MOBILE NETWORK BUSINESS UNIT. 10-1,1chome,Ohwatari-machi,Maebashi-city,371-8543,Japan Printed in Japan (No.20952) 200105(V)
Page 47
MX-G71R Block diagram FMA-006 FMC-022/024-1 FMH- FMH-031-2 FMB-028-5 IC 3 031-1 MAIN TUNER FM/DET MAIN HPF FM FRONTEND RELAY SOURCE SELECTOR POWER AMP AM/DET MAIN MUTE SYSTEM & E.VOL IC 1 IC602 IC481 IC436 VOLDA,VOKCK TAPE HARMONICS MW RF/OSC INPUT AMP...
MX-G71R PARTS LIST [ MX-G71R ] * All printed circuit boards and its assemblies are not available as service parts. CA-MXG71R / SP-MXG71R Area suffix B ------------------------------- U.K. E ----------- Continental Europe EN ------------ Northern Europe EV -------------- Eastern Europe...
MX-G71R Exploded view of general assembly and parts list Block No. Tuner board Display system control board Voltage Power supply board board Amplifier board CD servo Operation switch Main board control board Preset / tuning board switch board CD eject board...
Page 63
MX-G71R Parts list (General assembly) Parts list (General assembly) Block No. M1MM Block No. M1MM Item Parts number Parts name Q'ty Description Area Item Parts number Parts name Q'ty Description Area QYSPST2606Z SCREW GV10057-003A FRONT PANEL VKW5187-001 E75896-001 FELT SPACER...
Page 64
MX-G71R Parts list (General assembly) Block No. M1MM Item Parts number Parts name Q'ty Description Area GV10055-001A/S/ METAL COVER QYSDSG3006M T.SCREW M.COVER/C.BASE QYSBSGY3008E SPECIAL SCREW M.COVER/R.PANEL GV20106-005A CD FITTING(1) DISC 1 GV20107-005A CD FITTING(2) DISC 2 GV20108-005A CD FITTING(3) DISC 3...
MX-G71R CD changer mechanism assembly and parts list Block No. C3BASE-1M Grease = EM-30L = EBS0006-009B = FL-7750 FIG B FIG C FIG C FIG B Opposite side the same. FIG A FIG A CAUTION The axes of each gear...
Page 66
MX-G71R Parts list (CD changer mechanism) Block No. M2MM Item Parts number Parts name Q'ty Description Area VKS1144-004 CHASSIS VKS3698-003 TRAY GUIDE VKS5532-003 PULLEY GEAR VKB3000-164 BELT VKS5505-003 GEAR B VKS5506-002 GEAR C VKS5507-002 CROSS GEAR U VKS5508-002 CROSS GEAR L...
MX-G71R CD mechanism assembly and parts list Block No. Grease & Bond = EBS0006-013B = 1401B Turn table hight EXL-M7TMB Parts list (CD mechanism) Block No. M3MM Item Parts number Parts name Q'ty Description Area E102731-221SM CD MECHA BASE A...
MX-G71R Cassette mechanism assembly and parts list Block No. SLC-W101M Cassette switch board Head amplifier & mechanism control board...
Page 69
MX-G71R Parts list (Cassette mechanism) Block No. M4MM Item Parts number Parts name Q'ty Description Area VKS1165-00K MECHA CHASSIS VKR4749-003 IDLER PULLEY LV42026-001A SHAFT A MECHA VKH5786-003 SHAFT B MECHA VKS2274-002 REEL GEAR VKW5286-002 B.T. SPRING VKS5559-001 PLAY IDLE GEAR...
Page 70
MX-G71R Grease point =JC-525 Grease =UD-24 =LEN-320M =MOBIL-1 B mecha A mecha 3-11...
Page 71
MX-G71R Front view Rear view B - B (2/1) C - C (2/1) D - D (2/1) E - E (5/1) A - A (2/1, 2 places) (Dipping) 3-12...
Page 72
MX-G71R Electrical parts list (Regulator & amplifier board) Block No. 01 Item Parts number Parts name Remarks Area Item Parts number Parts name Remarks Area C 201 QFV72AJ-104Z MF CAPACITOR .10MF 5% 100V C 726 EETC1EM-106ZJC E CAPACITOR C 202...
Page 73
MX-G71R Electrical parts list (Regulator & amplifier board) Block No. 01 Item Parts number Parts name Remarks Area Item Parts number Parts name Remarks Area Q 240 KTC3199/GL/-T TRANSISTOR R 618 QRE141J-221Y C RESISTOR 220 5% 1/4W Q 372 KTA1023/OY/-T...
MX-G71R Electrical parts list (Regulator & amplifier board) Block No. 01 Item Parts number Parts name Remarks Area R 776 QRE141J-102Y C RESISTOR 1.0K 5% 1/4W R 777 QRE141J-103Y C RESISTOR 10K 5% 1/4W R 778 QRE141J-103Y C RESISTOR 10K 5% 1/4W...
Page 75
MX-G71R Electrical parts list (Main board) Block No. 02 Item Parts number Parts name Remarks Area Item Parts number Parts name Remarks Area C 250 QETC1EM-226Z CAPACITOR 22MF 20% 25V C 531 QFVJ1HJ-274Z MF CAPACITOR .27MF 5% 50V C 251...
Page 76
MX-G71R Electrical parts list (Main board) Block No. 02 Item Parts number Parts name Remarks Area Item Parts number Parts name Remarks Area R 492 QRE141J-472Y C RESISTOR 4.7K 5% 1/4W FT112 QNG0020-001Z FUSE CLIP R 493 QRE141J-103Y C RESISTOR...
Page 77
MX-G71R Electrical parts list (Front board) Block No. 03 Item Parts number Parts name Remarks Area Item Remarks Parts number Parts name Area C 233 QFVJ1HJ-104Z MF CAPACITOR .10MF 5% 50V D 650 1SS133-T2 SI DIODE C 308 EETC1HM-106ZJC E CAPACITOR...
Page 78
MX-G71R Electrical parts list (Front board) Block No. 03 Item Remarks Parts number Parts name Area Item Parts number Parts name Remarks Area Q 816 2SD1991A/RS/-T TRANSISTOR R 829 QRE141J-103Y C RESISTOR 10K 5% 1/4W Q 817 2SD1991A/RS/-T TRANSISTOR R 831...
Page 79
MX-G71R Electrical parts list (Front board) Block No. 03 Item Remarks Parts number Parts name Area Item Parts number Parts name Remarks Area R 911 QRE141J-102Y C RESISTOR 1.0K 5% 1/4W S 942 QSW0674-001Z TACT SWITCH R 912 QRE141J-103Y C RESISTOR...
Page 80
MX-G71R Electrical parts list (Tuner board) Block No. 04 Item Parts number Parts name Remarks Area Item Remarks Parts number Parts name Area NCB21HK-223X C CAPACITOR CN 1 QGF1205F1-13 CONNECTOR NCB21HK-103X C CAPACITOR 1SS133-T2 SI DIODE EETC1CM-106ZJC E CAPACITOR 1SS133-T2...
Page 81
MX-G71R Electrical parts list (CD servo control board) Block No. 05 Item Parts number Parts name Remarks Area Item Parts number Parts name Remarks Area C 251 NCS21HJ-100X C CAPACITOR C 821 NCF21CZ-105X C CAPACITOR C 252 NCS21HJ-100X C CAPACITOR...
Page 82
MX-G71R Electrical parts list (CD servo control board) Block No. 05 Item Parts number Parts name Remarks Area Item Remarks Parts number Parts name Area R 619 NRSA02J-153X MG RESISTOR R 811 NRSA02J-103X MG RESISTOR R 620 NRSA02J-564X MG RESISTOR...
Page 83
MX-G71R Electrical parts list (Head amplifier & mechanism contorl board) Block No. 07 Item Remarks Item Parts number Parts name Remarks Area Parts number Parts name Area CN301 QGF1205F1-06 CONNECTOR A HEAD D3302 1SR139-400-T2 SI DIODE CN302 QGF1205F1-06 CONNECTOR B HEAD D3307 DZ5.1BSB-T2...
Page 84
MX-G71R Electrical parts list (Head amplifier & mechanism control board) Block No. 07 Item Remarks Parts number Parts name Area R3327 QRE141J-474Y C RESISTOR 470K 5% 1/4W R3330 QRE141J-103Y C RESISTOR 10K 5% 1/4W R3331 QRE141J-103Y C RESISTOR 10K 5% 1/4W...
MX-G71R Parts list (Packing) Block No. M5MM Item Parts number Parts name Q'ty Description Area GV20115-003A PACKING CASE CA-MXG71R GV10071-002A UPPER CUSHION CA-MXG71R GV10072-002A BOTTOM CUSHION CA-MXG71R QPC06507015P POLY BAG CA-MXG71R GV30209-001A SPACER CA-MXG71R GV40168-003A SHEET CA-MXG71R QPC02503515P POLY BAG...