Advertisement
Quick Links
NOTE:
Please read all instructions
carefully before using this
product
Safety Notice
Hardware Identifier
Assembly Instruction
Parts List
Warranty
Ordering Parts
Model
IGS-08
Retain This
Manual for
Reference
02-08-02
OWNER'S
MANUAL
NARROW BENCH
IMPEX FITNESS PRODUCTS
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (800) 999-8899 Fax: (626) 961-9966
www.impex-fitness.com
info@impex-fitness.com
IGS-08
Advertisement
Related Manuals for Impex IRON GRIP SPORT IGS-08
Summary of Contents for Impex IRON GRIP SPORT IGS-08
- Page 1 Hardware Identifier NARROW BENCH Assembly Instruction Parts List Warranty Ordering Parts Model IGS-08 Retain This Manual for Reference 02-08-02 OWNER'S IMPEX FITNESS PRODUCTS MANUAL 14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746 Tel: (800) 999-8899 Fax: (626) 961-9966 www.impex-fitness.com info@impex-fitness.com...
-
Page 2: Table Of Contents
WARRANTY....................… 10 ORDERING PARTS..................10 BEFORE YOU BEGIN Thank you for selecting the IRON GRIP SPORT IGS-08 Narrow Bench by IMPEX FITNESS PRODUCTS. For your safety and benefit, read this manual carefully before using the machine. As a manufacturer, we are committed to provide you complete customer satisfaction. -
Page 3: Important Safety Notices
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC. ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT. -
Page 5: Assembly Instructions
ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Adjustable Wrench and Allen Wrench NOTE: It is strongly recommended this machine to be assembled by two or more people to avoid possible injury. STEP 1 (See Diagram 1) A.) Attach the Rear Stabilizer (#11) to the bottom of the Upright Beam (#9). Secure it with one Bracket (#15), four M10 x 2 ¾”... - Page 6 STEP 2 (See Diagram 2) A.) Attach the rear of the Main Seat Support (#25) to the Upright Beam (#9). Secure it with two M10 x 2 ¾” Allen Bolts (#16), four ∅ ¾” Washers (#13), and two M10 Aircraft Nuts (#14). Do not tighten the nuts and bolts yet. B.) Slide the Sliding Block (#22) onto the Main Seat Support (#25).
- Page 7 STEP 3 (See Diagram 3) A.) Attach two Seat Supports (#20), one on each side, to the pivot on the Sliding Block (#22). Secure the Seat Supports (#20) to the two rear holes on the Seat Pad (#1) using two M8 x 1 3/4” Allen Bolts (#18) and ∅ ½” Washers (#19). B.) Attach the Seat Incline Adjustment (#27) to the two front holes on the Seat Pad.
- Page 8 STEP 4 (See Diagram 4) A.) Insert the Leg Developer Holder (#41) into the opening on the Front Stabilizer (#40). Secure it with the Lock Knob (#6). B.) Attach the Leg Developer (#38) to the bracket on the Leg Developer Holder (#41). Secure it with a M12 x 2 3/8”...
-
Page 10: Parts List
PARTS LIST KEY NO. DESCRIPTION Q’ty Seat Pad Backrest Board 2” x 2 ¾” Sleeve Crutch Olympic Sleeve Lock Knob Backrest Adjustment Bar 1 ½” Square End Cap Upright Beam 2” End Cap Rear Stabilizer M10 x 2 ¾” Carriage Bolt ∅... -
Page 11: Warranty
No other warranty beyond that specifically set forth above is authorized by IMPEX. IMPEX is not responsible or liable for indirect, special or consequential damages arising out of or in connection with the use or performance of the product or other damages with respect to any economic loss, loss of property, loss of revenues or profits, loss of enjoyments or use, costs of removal, installation or other consequential damages or whatsoever natures.