Download Print this page

Impex MARCY PRO MWB-5085 Owner's Manual

Weight bench

Advertisement

Quick Links

NOTE:
Please read all
instructions carefully
before using this product
Table of Contents
Safety Notice
Hardware Identifier
Assembly Instruction
Parts List
Warranty
Ordering Parts
Model
MWB-5085
Retain This
Manual for
Reference
170630
OWNER'S
MANUAL
MARCY PRO
WEIGHT BENCH
MWB-5085
IMPEX
2801 S. Towne Ave., Pomona, CA 91766
Tel: (800) 999-8899 Fax: (626) 961-9966
www.marcypro.com
support@impex-fitness.com
®
INC.

Advertisement

loading

Summary of Contents for Impex MARCY PRO MWB-5085

  • Page 1 Safety Notice MWB-5085 Hardware Identifier Assembly Instruction Parts List Warranty Ordering Parts Model MWB-5085 Retain This Manual for Reference 170630 OWNER'S ® IMPEX INC. MANUAL 2801 S. Towne Ave., Pomona, CA 91766 Tel: (800) 999-8899 Fax: (626) 961-9966 www.marcypro.com support@impex-fitness.com...
  • Page 2: Table Of Contents

    ORDERING PARTS..................BEFORE YOU BEGIN Thank you for selecting the MARCY PRO Weight Bench MWB-5085 by ® IMPEX INC. For your safety and benefit, read this manual carefully before using the machine. As a manufacturer, we are committed to provide you complete customer satisfaction.
  • Page 3: Important Safety Notice

    PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC. ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.
  • Page 4 WARNING LABEL PLACEMENT The Warning Label shown here has been placed on the Cross Brace. If the label is missing or illegible, please call customer service at 1-800-999-8899 for replacement. Apply the label in location shown. www.marcypro.com ©Impex...
  • Page 5: Hardware Identifier

    HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size. www.marcypro.com ©Impex...
  • Page 6: Assembly Instructions

    (#13), two M10 x 3 1/8” Carriage Bolts (#34), two ∅ ¾” Washers (#45), and two M10 Aircraft Nuts (#47). C.) Place Backrest Adjustment Bar (#9) between the two Upright Beams onto selected slots to obtain desired Backrest Incline. DIAGRAM 1 www.marcypro.com ©Impex...
  • Page 7 Beam (#1) and secure with a M10 Lock Knob (#32). Repeat the same step to install the other Butterfly to Left Upright Beam (#2), G.) Securely tighten all Nuts and Bolts installed in Step-1 and Step-2. DIAGRAM 2 www.marcypro.com ©Impex...
  • Page 8 Bolt (#42) and one Ø ¾” Large Washer (#46). Repeat same step to install the other Butterfly Handle to the left Butterfly. D.) Do not over tighten Nut and Bolts. Make sure the Leg Developer and Butterfly can swivel freely. DIAGRAM 3 www.marcypro.com ©Impex...
  • Page 9 5/8” Allen Bolts (#37) and two Ø 5/8” Washers (#44). E.) Insert the Arm Curl Stand into the opening on Front Post (#5). Use the M10 x 2 3/8” Lock Knob (#31) to lock it in position. DIAGRAM 4 www.marcypro.com ©Impex...
  • Page 10 A.) Insert two Foam Tubes (#11) halfway through the holes on Leg Developer (#7). Push four Foam Rolls (#20) onto the Tubes from both ends. B.) Attach a Spring Clip (#21) to the weight post on Leg Developer and Butterfly. DIAGRAM 5 www.marcypro.com ©Impex...
  • Page 11: Exploded Diagram

    ©Impex...
  • Page 12: Parts List

    M6 x 1 3/8” Hex Bolt M10 x 5 1/8” Hex Bolt M10 x 5/8” Allen Bolt Ø ½” Washer Ø 5/8” Washer Ø ¾” Washer Ø ¾” Large Washer M10 Aircraft Nut M8 Aircraft Nut Long Hex Nut www.marcypro.com ©Impex...
  • Page 13: Warranty

    IMPEX. IMPEX is not responsible or liable for indirect, special or consequential damages arising out of or in connection with the use or performance of the product or other damages with respect to any economic loss, loss of property, loss of revenues or profits, loss of enjoyments or use, costs of removal, installation or other consequential damages or whatsoever natures.