Advertisement
Quick Links
NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
MARCY WEIGHT BENCH
Safety Notice
MWB-209
Hardware Pack
Assembly Instruction
Parts List
Warranty
Ordering Parts
Model
MWB 209
Retain This
Manual for
Reference
110624
OWNER'S
®
IMPEX
INC.
MANUAL
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (800) 999-8899 Fax: (626) 961-9966
www.impex-fitness.com
info@impex-fitness.com
Advertisement
Related Manuals for Impex MARCY MWB-209
Summary of Contents for Impex MARCY MWB-209
- Page 1 Hardware Pack Assembly Instruction Parts List Warranty Ordering Parts Model MWB 209 Retain This Manual for Reference 110624 OWNER'S ® IMPEX INC. MANUAL 14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746 Tel: (800) 999-8899 Fax: (626) 961-9966 www.impex-fitness.com info@impex-fitness.com...
-
Page 2: Table Of Contents
ORDERING PARTS...................11 BEFORE YOU BEGIN ® Thank you for selecting the MARCY Weight Bench MWB-209 by IMPEX INC. For your safety and benefit, read this manual carefully before using the machine. As a manufacturer, we are committed to provide you complete customer satisfaction. -
Page 3: Important Safety Notice
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC. ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT. - Page 4 WRANING LABEL PLACEMENT The warning label shown here have been placed on the Cross Brace. If the label is missing or illegible, please call customer service at 1-800-888-8899 for replacements. Apply the label in the location shown.
-
Page 5: Hardware Pack
Hardware Pack NOTE: The following parts are not drawn to scale. Please use your own ruler or scale to measure the size. -
Page 6: Assembly Instructions
ASSEMBLY INSTRUCTION Tools Required for Assembling the Machine: Two Adjustable Wrenches. NOTE: It is strongly recommended that two or more people assemble this machine to avoid possible injury. STEP 1 (See Diagram 1) A.) Bench should be placed on flat surface. The incline or decline of surface should be limited to 3% or less for best performance and safely. - Page 7 STEP 2 (See Diagram 2) A.) Do not tighten the Nut and Bolt until instructed to do so. B.) Attach the Front Support (#5) to Main Seat Support (#3). Secure it with one M8 x 1 5/8” Carriage Bolt (#26), one Ø 5/8” Washer (#24), and one M8 Aircraft Nut (#22). Attach the other end of Main Seat Support to the Cross Brace (#2).
- Page 8 STEP 3 (See Diagram 3) A.) Attach the Leg Developer (#6) to the open bracket on the Front Support (#5). Secure it with one M10 x 2 3/8” Hex Bolt (#19), one Ø ¾” Washer (#29), and one M10 Aircraft Nut (#25).
- Page 9 STEP 4 (See Diagram 4) A.) Attach the side-holes on the two Backrest Supports (#7) to the pivot on the Main Seat Support (#3). Place the other end of the Backrest Supports against the Backrest Adjustment Bar (#11). B.) Attach the Backrest Board (#8) to the Backrest Supports. Secure it with four M6 x 1 5/8”...
-
Page 11: Parts List
PARTS LIST KEY NO. DESCRIPTION Q’ty Upright Beam Cross Brace Main Seat Support Diagonal Support Front Support Leg Developer Backrest Support Backrest Board Seat Pad Bracket Backrest Adjustment Bar Foam Roll Foam Tube Ø ¾” End Cap Ø 1” End Cap M8 x 2 3/8”... -
Page 12: Warranty
Service Department at 1-800-999-8899. The customer must prepay all freights on products returned to IMPEX. This warranty does not extend to any product or damage to a product caused by or attributable to freight damage, abuse, misuse, improper or abnormal usage. No other warranty beyond that specifically set forth above is authorized by IMPEX.