Lorex LWB3801 Series Quick Connection Manual

HD Wire-Free Security System
1 / 2
English Version 6.0
Package Contents
Rechargeable
HD Wire-Free Security Cameras
Power Pack*
(Model Number: LWB3801)
DVR Power
USB Mouse Remote Control
Adapter
STEP 1: Initial Setup
Before you begin, you will need to prepare the wire-free cameras and
power packs.
To prepare the cameras and receiver:
ATTENTION: Fully charge the power pack before use.
1. Remove the power pack from each camera by pushing
both release buttons*, then pulling down on the power
pack. Place your hand underneath the power pack when
removing to prevent it from falling.
2. Peel off the PLEASE REMOVE label covering the
contacts on each power pack.
3. Insert the charged power packs into each camera base.
Push up until the power pack 'clicks' firmly into place.
4. Twist the adjustment ring near the camera base
counterclockwise to loosen and reposition each camera
as shown to the right. Connect one of the white antennas
to each camera.
* Top view
STEP 2: Setting Up the DVR
Next, you must set up the DVR and connect the wireless receiver.
To set up the DVR:
1. Connect the wireless receiver to
the USB port on the back panel of
the DVR.
NOTE: The receiver includes double-sided tape and
mounting screws for optional wall mounting for
improved line-of-sight with cameras.
2. Connect the DVR to your router using
the included Ethernet cable.
3. Connect the included power adapter
to the DVR. Wait a few minutes for
the system to start up.
OPTIONAL: Full DVR Setup
• This guide describes basic setup of the DVR only.
This installation is intended for users who wish to
monitor their system using the free Lorex Cirrus
app on their smartphone or tablet.
• You may choose to connect the included USB
mouse and a monitor with HDMI or VGA cable (not
included) for complete control over your wire-free
security system using the DVR. See the included
Quick Reference Guide for details.
Quick Connection Guide
www.lorex.com
* Per camera in multi-camera packs
HD DVR
(Model Number: LHB906)
Camera / Receiver Wireless
Antennas* Receiver
Power Pack
Ethernet Cable
Adapter
*
Adjustment ring
HDMI OR VGA*
STEP 3: Connecting with Lorex Cirrus
Connect to your system using the free Lorex Cirrus app for smartphones and tablets
(iOS and Android).
To connect with Lorex Cirrus:
1. Download and install the free Lorex Cirrus app from the App Store
or Google Play Store.
2. Tap the Lorex Cirrus icon to launch the app.
3. Tap to open the menu. Tap Devices, then tap Add.
4. Enter the following:
A
B
C
D
E
5. Enter a new, secure 8-15 character password. This password will be used to connect
to your system from now on.
Record your password below and store in a secure place:
NOTE: If you have manually set your DVR, use the same password created during
that setup. The default password will not work.
STEP 4: Pairing the Cameras
Next, you must pair each camera to your recorder. You can pair cameras using the
Mounting Kit*
Lorex Cirrus app, or with the recorder.
To pair cameras using the Lorex Cirrus app:
1. From Live view, tap any free
channel you would like to
pair a camera to (marked
HDMI Cable
with a icon).
*
NOTE: A "pairing successful" message should appear on screen. If you do not see this message,
repeat the steps above.
To pair cameras using the recorder:
Hover the mouse pointer near the top of an empty channel
*
and click .
You will then have 30 seconds to press and hold the pair
button on the back of your camera (shown above).
NOTE: If you do not see video from one or more cameras,
ensure you have removed the PLEASE REMOVE label from the
power pack. If the issue persists, see the "Troubleshooting"
section on the back of this document.
Visit us online for up-to-date software and complete instruction manuals.
As our products are subject to continuous improvement, Lorex reserves the right to modify product design,
specifications and prices, without notice and without incurring any obligation. E&OE. All rights reserved.
* Not included
A Ensure Device ID is selected.
F
Tap to scan the QR code on the back of
B
your recorder using the camera on your
mobile device.
C Ensure the Client Port reads 35000.
Enter the username (default: admin).
D
E Enter the password (default: 00000000).
F Tap Save.
2. Tap PAIR. A timer 3. Press and hold the pair button on the
for 30 seconds
appears.
Need Help?
1
Visit lorex.com
Search for the model number
2
of your product
Click on your product in the
3
search results
4
Click on the Downloads tab
Copyright © 2020 Lorex Corporation
back of the camera for 3 seconds.
LWB3800 / LWB3900 Series
LHB900_QCG_EN_R6