Ordering Spare Parts - Stihl MS 362 C-M Instruction Manual

English
Engine power to ISO 7293: 3.5 kW (4.8 bhp) at
1)
Idle speed:
31.2 Ignition System
Electronic magneto ignition
Spark plug (resistor type): NGK CMR 6 H,
Electrode gap:
31.3 Fuel System
All position diaphragm carburetor with integral
fuel pump
Fuel tank capacity:
31.4 Chain Lubrication
Fully automatic, speed-controlled oil pump with
rotary piston. Additional manual oil flow control
Oil tank capacity: 325 cc (0.325 l)
31.5 Weight
dry, without bar and chain
MS 362 C-M:
MS 362 C-M with handle and carbu‐
retor heating:
31.6 Cutting Attachment
Actual cutting length may be less than the speci‐
fied length
31.6.1 Rollomatic guide bars
Bar lengths (3/8" pitch):
Groove width:
31.6.2 3/8" chains
Rapid Micro (36 RM) Type 3652
Rapid Super (36 RS) Type 3621
Rapid Super 3 (36 RS3) Type 3626
Pitch:
Drive link gauge:
31.6.3 Chain Sprockets
7-tooth for 3/8" (rim sprocket)
Max. chain speed according to
ISO 11681:
Chain speed at maximum power
output:
31.7 Noise and Vibration Data
For further details on compliance with Vibration
Directive 2002/44/EC see www.stihl.com/vib.
31.7.1 Sound pressure level L
105 dB(A)
1)
to ISO 11681 +/- 50 rpm
38
10,000 rpm
2,800 rpm
BOSCH USR 4AC
0.5 mm
600 cc (0.6 l)
5.6 kg
5.8 kg
37, 40, 45, 50 cm
1.6 mm
3/8" (9.32 mm)
1.6 mm
28.9 m/s
21.7 m/s
to ISO 22868
p
31.7.2 Sound power level L
117 dB(A)
31.7.3 Vibration measurement a
ISO 22867
Left handle:
Right handle:
The K‑factor in accordance with Directive
2006/42/EC is 2.0 dB(A) for the sound pressure
level and sound power level; the K‑factor in
accordance with Directive 2006/42/EC is
2
2.0 m/s for the vibration level.
31.8 REACH
REACH is an EC regulation and stands for the
Registration, Evaluation, Authorisation and
Restriction of Chemical substances.
For information on compliance with the REACH
regulation (EC) No. 1907/2006 see
www.stihl.com/reach.
31.9 Exhaust Emissions
The CO value measured in the EU type approval
2
procedure is specified at www.stihl.com/co2.
The measured CO value was determined on a
2
representative engine in accordance with a
standardized test procedure under laboratory
conditions and does not represent either an
explicit or implied guarantee of the performance
of a specific engine.
The applicable exhaust emission requirements
are fulfilled by the intended usage and mainte‐
nance described in this instruction manual. The
type approval expires if the engine is modified in
any way.

32 Ordering Spare Parts

Please enter your saw model, serial number as
well as the part numbers of the guide bar and
saw chain in the spaces provided. This will make
re-ordering simpler.
The guide bar and saw chain are subject to nor‐
mal wear and tear. When purchasing these
parts, always quote the saw model, the part
numbers and names of the parts.
Model
Serial number
32 Ordering Spare Parts
to ISO 22868
w
to
hv, eq
2
3.5 m/s
2
3.5 m/s
0458-154-8321-C