Advertisement

ROG STRIX
Z590-E
GAMING
Series

Advertisement

Table of Contents
loading

Summary of Contents for Asus ROG STRIX Z590-E GAMING Series

  • Page 1 ROG STRIX Z590-E GAMING Series...
  • Page 2 Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the product is defaced or missing.
  • Page 3: Table Of Contents

    Contents Safety information ....................... v About this guide ......................vi ROG STRIX Z590-E GAMING Series specifications summary ......vii Connectors with shared bandwidth ............... xiii Package contents ...................... xv Installation tools and components ................. xvi Chapter 1: Product Introduction Before you proceed ................... 1-1 Motherboard layout ..................
  • Page 4 Appendix Q-Code table ......................A-1 Notices ........................A-5 Warranty ......................... A-12 ASUS contact information ..................A-14...
  • Page 5: Safety Information

    Safety information Electrical safety • To prevent electrical shock hazard, disconnect the power cable from the electrical outlet before relocating the system. • When adding or removing devices to or from the system, ensure that the power cables for the devices are unplugged before the signal cables are connected. If possible, disconnect all power cables from the existing system before you add a device.
  • Page 6: About This Guide

    Refer to the following sources for additional information and for product and software updates. ASUS website The ASUS website (www.asus.com) provides updated information on ASUS hardware and software products. Optional documentation Your product package may include optional documentation, such as warranty flyers, that may have been added by your dealer.
  • Page 7: Rog Strix Z590-E Gaming Series Specifications Summary

    Core™ processors support 3200 / 2933 / 2800 / 2666 / 2400 / ® 2133 natively. * Refer to www.asus.com for the Memory QVL (Qualified Vendors Lists), and memory frequency support depends on the CPU types. 1 x DisplayPort 1.4** 1 x HDMI™...
  • Page 8 ROG STRIX Z590-E GAMING Series specifications summary Total supports 4 x M.2 slots and 6 x SATA 6Gb/s ports Intel ® & 10 Gen Processors* M.2_1 slot (Key M), type 2242/2260/2280/22110 - Only Intel Core™ processors support PCIe 4.0 x4 mode, this slot ®...
  • Page 9 ROG STRIX Z590-E GAMING Series specifications summary ROG SupremeFX 7.1 Surround Sound High Definition Audio CODEC ALC4080 - Impedance sense for front and rear headphone outputs - Supports: Jack-detection, Multi-streaming, Front Panel Jack-retasking - High quality 120 dB SNR stereo playback output and 113 dB SNR...
  • Page 10 - Pre-mounted I/O shield - SafeSlot AURA Sync - AURA RGB header(s) - Addressable Gen 2 RGB header(s) ASUS HYDRANODE - 1 x Chassis fan support* (CHA_FAN1P) * Visit ASUS Website for the latest compatibility list. (continued on the next page)
  • Page 11 ROG STRIX Z590-E GAMING Series specifications summary ROG Exclusive Software - RAMCache III - ROG CPU-Z - GameFirst VI - Sonic Studio III + Sonic Studio Virtual Mixer - Sonic Radar III - DTS Sound Unbound ® - Overwolf - Anti-virus software...
  • Page 12 • Specifications are subject to change without notice. Please refer to the ASUS website for the latest specifications. • MyASUS offers a variety of support features such as helping to troubleshoot issues, optimizing product performance, integrating ASUS software, and recovery drive...
  • Page 13: Connectors With Shared Bandwidth

    Connectors with shared bandwidth Configuration PCIEX16_1 PCIEX16_2 M.2_1 M.2_2 Configuration PCIEX16_3 SATA6G_56 Configuration M.2_4 SATA mode PCIe mode SATA6G_2 xiii...
  • Page 14 • PCIEX16_3 shares bandwidth with SATA6G_56. When PCEX16_ 3 is populated SATA6G_56 will be disabled. When PCIEX16_3 run at default x2 mode, SATA6G_56 is enabled. • When M.2_4 is operating in SATA device, SATA6G_2 will be disabled.
  • Page 15: Package Contents

    4 x SATA 6Gb/s cables 1 x Assistant fan (40mm) Additional Cooling Kit 1 x Screw package for cooling kit 1 x ASUS Wi-Fi moving antennas 1 x M.2 Q-Latch package 2 x M.2 Rubber Packages 1 x ROG key chain...
  • Page 16: Installation Tools And Components

    Installation tools and components Phillips (cross) screwdriver PC chassis Power supply unit Intel LGA 1200 CPU Intel LGA 1200 compatible CPU Fan ® ® DDR4 DIMM SATA hard disk drive SATA optical disc drive (optional) Graphics card (optional) M.2 SSD module (optional) 1 Bag of screws The tools and components in the table above are not included in the motherboard package.
  • Page 17: Chapter 1: Product Introduction

    Before you install or remove any component, ensure that the ATX power supply is switched off or the power cord is detached from the power supply. Failure to do so may cause severe damage to the motherboard, peripherals, or components. ROG STRIX Z590-E GAMING Series...
  • Page 18: Motherboard Layout

    Motherboard layout Chapter 1: Product Introduction...
  • Page 19 15. Front Panel Audio header 1-18 16. System Panel header 1-19 17. Thermal Sensor header 1-20 18. Thunderbolt™ header 1-21 19. TPM header 1-22 20. Q-Code LED 1-23 21. Q-LEDs 1-24 22. 8-pin Power Plug LED 1-24 ROG STRIX Z590-E GAMING Series...
  • Page 20: Cpu Socket

    Contact your retailer immediately if the PnP cap is missing, or if you see any damage to the PnP cap/socket contacts/motherboard components. ASUS will shoulder the cost of repair only if the damage is shipment/ transit-related.
  • Page 21: Dimm Slots

    (Double Data Rate 4) memory modules. A DDR4 memory module is notched differently from a DDR, DDR2, or DDR3 module. DO NOT install a DDR, DDR2, or DDR3 memory module to the DDR4 slot. Recommended memory configurations ROG STRIX Z590-E GAMING Series...
  • Page 22 (D/C) from the same vendor. Check with the vendor to get the correct memory modules. • Visit the ASUS website for the latest QVL. Chapter 1: Product Introduction...
  • Page 23: Expansion Slots

    Unplug the power cord before adding or removing expansion cards. Failure to do so may cause you physical injury and damage motherboard components. Please refer to the following tables for the recommended VGA configuration and Hyper M.2 configuration. ROG STRIX Z590-E GAMING Series...
  • Page 24 Recommended VGA configuration Slot Description Single VGA Dual VGA Triple VGA PCIe 4.0 x16_1 PCIe 4.0 x16_2 PCIe 4.0 x16_3 • We recommend that you provide sufficient power when running SLI mode. ® • Ensure to connect the 8-pin power plugs when running SLI mode.
  • Page 25: Fan And Pump Headers

    Fan and Pump headers The Fan and Pump headers allow you to connect fans or pumps to cool the system. When an ASUS HYDRANODE fan is connected to a ASUS HYDRANODE fan connector, the ASUS HYDRANODE function will be available.
  • Page 26: Vrm Heatsink Fan Header

    VRM Heatsink fan header The VRM Heatsink fan header is for connecting the VRM Heatsink fan on the integrated heatsink. Header Max. Current Max. Power Default Speed Shared Control CPU_FAN Q-Fan Controlled CPU_OPT Q-Fan Controlled CHA_FAN1P Q-Fan Controlled CHA_FAN2 Q-Fan Controlled CHA_FAN3 Q-Fan Controlled AIO_PUMP...
  • Page 27: Power Connectors

    • If you want to use two or more high-end PCI Express x16 cards, use a PSU with 1000W power or above to ensure the system stability. ROG STRIX Z590-E GAMING Series 1-11...
  • Page 28: Slot

    M.2 slot The M.2 slot allows you to install M.2 devices such as M.2 SSD modules. • Intel Core™ processors: ® - M.2_1 supports PCIE 4.0 x4 mode M Key design and type 2242 / 2260 / 2280 / 22110 storage devices. - M.2_2 supports PCIE 4.0 x4 mode M Key design and type 2242 / 2260 / 2280 / 22110 storage devices.
  • Page 29 When M.2_4 is operating in SATA mode, SATA6G_2 will be disabled. • Before creating a RAID set, refer to the RAID Configuration Guide. You can download the RAID Configuration Guide from the ASUS website. ROG STRIX Z590-E GAMING Series 1-13...
  • Page 30: Usb 3.2 Gen 2X2 Type-C ® Front Panel Connector

    USB 3.2 Gen 2x2 Type-C Front Panel connector ® The USB 3.2 Gen 2x2 Type-C connector allows you to connect a USB 3.2 Gen 2x2 ® Type-C module for additional USB 3.2 Gen 2x2 ports on the front panel. The USB 3.2 ®...
  • Page 31: Usb 2.0 Header

    2.0 ports. The USB 2.0 header provides data transfer speeds of up to 480 Mb/s connection speed. DO NOT connect a 1394 cable to the USB connectors. Doing so will damage the motherboard! The USB 2.0 module is purchased separately. ROG STRIX Z590-E GAMING Series 1-15...
  • Page 32: Aura Addressable Gen2 Header

    AURA Addressable Gen2 header The Addressable Gen2 header allows you to connect individually addressable RGB WS2812B LED strips or WS2812B based LED strips. The Addressable Gen2 header supports WS2812B addressable RGB LED strips (5V/ Data/Ground), with a maximum power rating of 3A (5V), and the addressable headers on this board can handle a combined maximum of 500 LEDs.
  • Page 33: Aura Rgb Header

    RGB LED strip is connected in the correct orientation, and the 12V connector is aligned with the 12V header on the motherboard. • The LED strip will only light up when the system is powered on. • The LED strip is purchased separately. ROG STRIX Z590-E GAMING Series 1-17...
  • Page 34: Cpu Over Voltage Jumper

    CPU Over Voltage jumper The CPU Over Voltage jumper allows you to set a higher CPU voltage for a flexible overclocking system (depending on the type of the installed CPU). Set to pins 2-3 to increase the CPU voltage setting, or set to pins 1-2 to use the default CPU voltage setting.
  • Page 35: System Panel Header

    The chassis intrusion sensor or switch sends a high-level signal to the header when a chassis component is removed or replaced, the signal is then generated as a chassis intrusion event. ROG STRIX Z590-E GAMING Series 1-19...
  • Page 36: Thermal Sensor Header

    Thermal Sensor header The Thermal Sensor header allows you to connect a sensor to monitor the temperature of the devices and the critical components inside the motherboard. Connect the thermal sensor and place it on the device or the motherboard’s component to detect its temperature.
  • Page 37: Thunderbolt™ Header

    Thunderbolt™-enabled devices to form a daisy-chain configuration. • The add-on Thunderbolt™ I/O card and Thunderbolt™ cables are purchased separately. • Please visit the official website of your purchased Thunderbolt™ card for more details on compatibility. ROG STRIX Z590-E GAMING Series 1-21...
  • Page 38: Tpm Header

    TPM header The TPM header allows you to connect a TPM module, which securely stores keys, digital certificates, passwords, and data. A TPM system also helps enhance network security, protect digital identities, and ensures platform integrity. The TPM module is purchased separately. Chapter 1: Product Introduction 1-22...
  • Page 39: Q-Code Led

    The Q-Code LEDs provide the most probable cause of an error code as a starting point for troubleshooting. The actual cause may vary from case to case. • Please refer to the Q-Code table in the Appendix section for more details. ROG STRIX Z590-E GAMING Series 1-23...
  • Page 40: Q-Leds

    Q-LEDs The Q-LEDs check key components (CPU, DRAM, VGA, and booting devices) during the motherboard booting process. If an error is found, the critical component’s LED stays lit up until the problem is solved. The Q-LEDs provide the most probable cause of an error code as a starting point for troubleshooting.
  • Page 41: Building Your Pc System

    NOT install a CPU designed for LGA1155, LGA1156, and LGA1151 sockets on the LGA1200 socket. • ASUS will not cover damages resulting from incorrect CPU installation/removal, incorrect CPU orientation/placement, or other damages resulting from negligence by the user. ROG STRIX Z590-E GAMING Series...
  • Page 42 Chapter 2: Basic Installation...
  • Page 43: Cooling System Installation

    2.1.2 Cooling system installation Apply Thermal Interface Material to the CPU cooling system and CPU before you install the cooling system, if necessary. To install a CPU heatsink and fan assembly ROG STRIX Z590-E GAMING Series...
  • Page 44 To install an AIO cooler If you wish to install an AIO cooler, we recommend installing the AIO cooler after installing the motherboard into the chassis. W_PUMP+ / AIO_PUMP CPU_FAN CPU_OPT Chapter 2: Basic Installation...
  • Page 45: Dimm Installation

    2.1.3 DIMM installation To remove a DIMM ROG STRIX Z590-E GAMING Series...
  • Page 46: Installation

    2.1.4 M.2 installation Supported M.2 type varies per motherboard. • The illustrations only show the installation steps for a single M.2 slot, the steps are the same for the other M.2 slots if you wish to install an M.2 to another M.2 slot. •...
  • Page 47 • To install an M.2 to the maximum length the M.2 slot supports For M.2_1: Type 22110 M.2 Remove the plastic film from the thermal pad. Install your M.2 to the M.2 slot. ROG STRIX Z590-E GAMING Series...
  • Page 48 • To install an M.2 using the removable screw stand For M.2_1: Type 2242, 2260, 2280 M.2 A. (optional) Remove the black screw if there is a black screw installed in the M.2 slot length screw hole you wish to install your M.2 to. Follow this step only if you wish to install an M.2 to type 2242.
  • Page 49 Remove the plastic film from the thermal pads on the bottom of the heatsink. Replace the heatsink. Secure the heatsink using the screws removed previously. ROG STRIX Z590-E GAMING Series...
  • Page 50 For M.2_2, M.2_3, and M.2_4 Remove the screws from the heatsinks. Remove the heatsink. Chapter 2: Basic Installation 2-10...
  • Page 51 B. Rotate and adjust the M.2 Q-latch so that the handle points away from the M.2 slot. C. Install your M.2 to the M.2 slot. D. Rotate the M.2 Q-Latch clockwise to secure the M.2 in place. ROG STRIX Z590-E GAMING Series 2-11...
  • Page 52 • To install an M.2 using the removable M.2 Q-Latch screw For M.2_2: Type 2242, 2260, 2280 M.2 For M.2_3: Type 2242, 2260, 2280 M.2 For M.2_4: Type 2242, 2260 M.2 (optional) Remove the M.2 rubber pad. Follow this step only if you wish to install an M.2 to type 2242. (optional) If required, remove the pre-installed removable M.2 Q-Latch screw at the 2280 length screw hole.
  • Page 53 Remove the plastic film from the thermal pads on the bottom of the heatsink. Replace the heatsink. Secure the heatsink using the screws removed previously. ROG STRIX Z590-E GAMING Series 2-13...
  • Page 54: Additional Cooling Kit Installation

    2.1.5 Additional cooling kit installation VRM_HS_FAN When using high performance settings whilst overclocking, ensure to install the bundled fan onto the MOS fan holder. • You may install 12V (1A, 12W), 40mm x 40mm fans. • You may adjust the height of the fan holder to your preference when installing the fan holder.
  • Page 55: Motherboard Installation

    I/O panel. Place nine (9) screws into the holes indicated by circles to secure the motherboard to the chassis. DO NOT over tighten the screws! Doing so can damage the motherboard. ROG STRIX Z590-E GAMING Series 2-15...
  • Page 56: Atx Power Connection

    2.1.7 ATX power connection Ensure to connect the 8-pin power plug. Chapter 2: Basic Installation 2-16...
  • Page 57: Sata Device Connection

    2.1.8 SATA device connection ROG STRIX Z590-E GAMING Series 2-17...
  • Page 58: Front I/O Connector

    2.1.9 Front I/O connector To install the front panel connector To install USB 3.2 Gen 2x2 Type-C® connector USB 3.2 Gen 2x2 Type-C ® This connector will only fit in one orientation. Push the connector until it clicks into place. To install USB 3.2 Gen 1 connector To install USB 2.0 connector USB 2.0...
  • Page 59: Expansion Card Installation

    2.1.10 Expansion card installation To install PCIe x16 cards ROG STRIX Z590-E GAMING Series 2-19...
  • Page 60 To install Thunderbolt™ series card 6-pin PCIe power connector USB Type-C ® port connects to Thunderbolt devices MiniDP in port connects to DP out port on the motherboard or a VGA card USB 2.0 header Thunderbolt™ header Ensure to install the Thunderbolt™ series card to a PCIe slot from PCH. •...
  • Page 61: Wi-Fi Moving Antenna Installation

    2.1.11 Wi-Fi moving antenna installation Installing the ASUS Wi-Fi moving antenna Connect the bundled ASUS Wi-Fi moving antenna connector to the Wi-Fi ports at the back of the chassis. • Ensure that the ASUS Wi-Fi moving antenna is securely installed to the Wi-Fi ports.
  • Page 62: Bios Update Utility

    • Updating BIOS may have risks. If the BIOS program is damaged during the process and results to the system’s failure to boot up, please contact your local ASUS Service Center. Chapter 2: Basic Installation...
  • Page 63 For more information on using the BIOS FlashBack™ feature, please refer to https://www.asus.com/support/, or by scanning the QR code below. ROG STRIX Z590-E GAMING Series 2-23...
  • Page 64: Motherboard Rear And Audio Connections

    Motherboard rear and audio connections 2.3.1 Rear I/O connection Rear panel connectors DisplayPort USB 2.0 ports 11 and 12 USB 3.2 Gen 1 Type-A ports 1, 2, 3, and 4 Intel I225-V 2.5Gb Ethernet ports* ® HDMI™ port Clear CMOS button (CLR_CMOS). Press this button to clear the BIOS setup information only when the systems hangs due to overclocking.
  • Page 65: Audio I/O Connections

    Mic In Mic In Orange – – Center/Sub Center/Sub woofer woofer Black – Rear Speaker Out Rear Speaker Out Rear Speaker Out 2.3.2 Audio I/O connections Audio I/O ports Connect to Headphone and Mic ROG STRIX Z590-E GAMING Series 2-25...
  • Page 66 Connect to Stereo Speakers Connect to 2-channel Speakers Connect to 4-channel Speakers Chapter 2: Basic Installation 2-26...
  • Page 67 Connect to 5.1-channel Speakers Connect to 7.1-channel Speakers ROG STRIX Z590-E GAMING Series 2-27...
  • Page 68: Starting Up For The First Time

    Starting up for the first time After making all the connections, replace the system case cover. Ensure that all switches are off. Connect the power cord to the power connector at the back of the system chassis. Connect the power cord to a power outlet that is equipped with a surge protector. Turn on the devices in the following order: Monitor External storage devices (starting with the last device on the chain)
  • Page 69: Chapter 3: Bios And Raid Support

    Knowing BIOS The new ASUS UEFI BIOS is a Unified Extensible Interface that complies with UEFI architecture, offering a user-friendly interface that goes beyond the traditional keyboard- only BIOS controls to enable a more flexible and convenient mouse input. You can easily navigate the new UEFI BIOS with the same smoothness as your operating system.
  • Page 70: Bios Setup Program

    BIOS setup program Use the BIOS Setup to update the BIOS or configure its parameters. The BIOS screen include navigation keys and brief onscreen help to guide you in using the BIOS Setup program. Entering BIOS at startup To enter BIOS Setup at startup, press <Delete> or <F2> during the Power-On Self Test (POST).
  • Page 71: Asus Ez Flash 3

    ASUS EZ Flash 3 The ASUS EZ Flash 3 feature allows you to update the BIOS without using an OS-based utility. Ensure to load the BIOS default settings to ensure system compatibility and stability. Select the Load Optimized Defaults item under the Exit menu or press hotkey <F5>.
  • Page 72: Asus Crashfree Bios 3

    ASUS CrashFree BIOS 3 The ASUS CrashFree BIOS 3 utility is an auto recovery tool that allows you to restore the BIOS file when it fails or gets corrupted during the updating process. You can restore a corrupted BIOS file using a USB flash drive that contains the BIOS file.
  • Page 73: Raid Configurations

    For more information on configuring your RAID sets, please refer to the RAID Configuration Guide which you can find at https://www.asus.com/support, or by scanning the QR code. RAID definitions RAID 0 (Data striping) optimizes two identical hard disk drives to read and write data in parallel, interleaved stacks.
  • Page 74 Chapter 3: BIOS Setup...
  • Page 75 CPU self test failed or possible CPU cache error CPU micro-code is not found or micro-code update is failed Internal CPU error Reset PPI is not available Reserved for future AMI error codes 5C – 5F (continued on the next page) ROG STRIX Z590-E GAMING Series...
  • Page 76 Q-Code table Code Description S3 Resume is stared (S3 Resume PPI is called by the DXE IPL) S3 Boot Script execution Video repost OS S3 wake vector call E4 – E7 Reserved for future AMI progress codes S3 Resume Failed S3 Resume PPI not Found S3 Resume Boot Script Error S3 OS Wake Error...
  • Page 77 Reserved for ASL (see ASL Status Codes section below) Ready To Boot event Legacy Boot event Exit Boot Services event Runtime Set Virtual Address MAP Begin Runtime Set Virtual Address MAP End Legacy Option ROM Initialization System Reset (continued on the next page) ROG STRIX Z590-E GAMING Series...
  • Page 78 Q-Code table Code Description USB hot plug PCI bus hot plug Clean-up of NVRAM Configuration Reset (reset of NVRAM settings) Reserved for future AMI codes B8– BF CPU initialization error System Agent initialization error PCH initialization error Some of the Architectural Protocols are not available PCI resource allocation error.
  • Page 79 RF exposure compliance. HDMI Compliance Statement The terms HDMI, HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc. ROG STRIX Z590-E GAMING Series...
  • Page 80 Compliance Statement of Innovation, Science and Economic Development Canada (ISED) This device complies with Innovation, Science and Economic Development Canada licence exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
  • Page 81 Tenez cet appareil à distance du ventre des femmes enceintes et du bas-ventre des adolescents. ROG STRIX Z590-E GAMING Series...
  • Page 82 ASUS products sold in Vietnam, on or after September 23, 2011,meet the requirements of the Vietnam Circular 30/2011/TT-BCT. Các sản phẩm ASUS bán tại Việt Nam, vào ngày 23 tháng 9 năm2011 trở về sau, đều phải đáp ứng các yêu cầu của Thông tư 30/2011/TT-BCT của Việt Nam.
  • Page 83 DO NOT throw the mercury-containing button cell battery in municipal waste. This symbol of the crossed out wheeled bin indicates that the battery should not be placed in municipal waste. Regional notice for California WARNING Cancer and Reproductive Harm - www.P65Warnings.ca.gov ROG STRIX Z590-E GAMING Series...
  • Page 84 2014/53/EU. Cijeli di: https://www.asus.com/support/ tekst EU izjave o sukladnosti dostupan je na https://www.asus.com/support/ WiFi yang Beroperasi pada 5150-5350 MHz akan terbatas untuk penggunaan WiFi koji radi na opsegu frekvencija 5150-5350 MHz bit će ograničen na...
  • Page 85 ASUSTek Computer Inc. tukaj izjavlja, da je ta naprava skladna s temeljnimi zahtevami in drugimi relevantnimii določili Direktive 2014/53/EU. Polno besedilo izjave EU o skladnosti je na voljo na https://www.asus.com/ support/ WiFi, ki deluje v pasovnem območju 5150–5350 MHz, mora biti v državah, navedenih v spodnjem seznamu, omejen na notranjo uporabo: Declaración de conformidad simplificada para la UE...
  • Page 86 • ASUS offers a voluntary manufacturer’s Commercial Guarantee. • ASUS dragovoljno nudi komercijalno proizvođačko jamstvo. • ASUS reserves the right to interpret the provisions of the ASUS • ASUS zadržava prava na tumačenje odredbi ASUS komercijalnog Commercial Guarantee. jamstva. •...
  • Page 87 • Si tiene alguna queja o necesidad de un centro de reparación local Información de garantía de ASUS o el periodo de garantía del producto ASUS, por favor visite el sitio de Soporte de ASUS en https://www.asus.com/mx/support/ para • ASUS ofrece una garantía comercial voluntaria del fabricante.
  • Page 88 +1-510-739-3777 +1-510-608-4555 Web site https://www.asus.com/us/ Technical Support Support fax +1-812-284-0883 Telephone +1-812-282-2787 Online support https://qr.asus.com/techserv ASUS COMPUTER GmbH (Germany and Austria) Address Harkortstrasse 21-23, 40880 Ratingen, Germany Web site https://www.asus.com/de Online contact https://www.asus.com/support/Product/ContactUs/Services/ questionform/?lang=de-de Technical Support Telephone (DE) +49-2102-5789557 Telephone (AT)

Table of Contents