Panasonic KX-MB262CX Service Manual page 33

11.1.3. SERVICE FUNCTION TABLE (KX-MB772CX)
Code Function
501 Pause time set
503 Dial speed select
507 V34 transmission start speed
508 V34 reception start speed
514 Bell signal detect time
520 CED frequency select
521 International mode select
522 Auto standby select
523 Receive equalizer select
524 Transmission equalizer select
527 V.8 function select
529 Call Service Clear
550 Memory clear
551 ROM check
552 DTMF single tone test
553 Monitor on FAX
select
554 Modem test
555 Scanner test
556 Motor test
557 LED test
558 LCD test
561 KEY test
567 T0 timer
570 BREAK % select
573 Remote turn-on ring number set
590 FAX auto redial time set
591 FAX auto redial time disconnection
time set
592 CNG transmit select
Set Value
X 100 msec 001~600
1:10 pps 1, 2
2:20 pps
0: Disable 0~8
1: 33.6
2: 31.2
3: 28.8
4: 26.4
5: 24.0
6: 21.6
7: 19.2
8: 16.8
0: Disable 0~8
1: 33.6
2: 31.2
3: 28.8
4: 26.4
5: 24.0
6: 21.6
7: 19.2
8: 16.8
X 100msec 1~9
1:2100 Hz 1, 2
2:1100 Hz
1:ON 2:OFF 1, 2
1:ON 2:OFF 1, 2
1: 0 km 1~4
2: 1.8 km
3: 3.6 km
4: 7.2 km
1: 0 km 1~4
2: 1.8 km
3: 3.6 km
4: 7.2 km
1:OFF 2:ON 1, 2
1:ON 2:OFF 1, 2
communication 1:OFF 1~3
2:PHASE B
3:ALL
001~255 001~255
1:61% 2:67% 1, 2
X number of 00~99
rings
X number of 00~99
times
X second 001~999
1:OFF 1~3
2:ALL
3:AUTO
Effective Default
Range
030 ----------
1 ----------
1 If the code 527 is set at 2, the code 507 and 508
work.
1 If the code 527 is set at 2, the code 507 and 508
work.
6 ----------
1 See Symptom/Countermeasure Table for long dis-
tance and international calls i n (P.142).
1 See Symptom/Countermeasure Table for long dis-
tance and international calls i n (P.142).
1 The resolution reverts to the default when transmis-
sion is complete.
1 Set RX equalizer to automatic mode.
1
2
Refer to Memory Clear Specification (P.87).
See (P.80).
2
See (P.80).
1 Sets whether to monitor the line signal with the
unit's speaker during FAX communication or not.
See (P.80).
See (P.80).
0
See (P.80).
See (P.80).
See (P.80).
See (P.80).
052 Sets a higher value when the response from the
other party needs more time during automatic FAX
transmission.
1 Sets the % break of pulse dialing according PBX.
10 Sets the number of rings before the unit starts to
operate TAM in the TEL mode.
05 Selects the number of redial times during FAX com-
munication (not including the first dial).
185 Sets the FAX redial interval during FAX communi-
cation.
2 Lets you select the CNG output during FAX trans-
mission. ALL: CNG is output at phase A. AUTO:
CNG id output only when automatic dialing is per-
KX-MB262CX/KX-MB772CX
Remarks