Table of Contents
Advertisement
Section 6: Specifications & Capacities
Section 6: Specifications & Capacities
Tractor horsepower
Gearbox horsepower
Center & wings
Gearbox shafts
Output shaft
Gearbox capacity & lubrication
Center & wings
Cutting capacity
Hitch weight
Machine weight
Blade tip speed At 540 rpm
Hitch types
Hitch jack
Cutting width
Overall cutter width
Minimum transport width
Overall length
Deck height
Cutting height
Lift hydraulics
Wing folding hydraulics
Wing flex while operating
Wing transport protection
Deck material
Side skirt material
Skid shoes
Blade rotation
Center deck
Blades - 6 (2 per deck)
Blade overlap
Blade bolt
Stump jumper / blade holder
Front & rear guards
Input driveline
Intermediate & wing drivelines
Wheels
Number of wheels
Transport axle
Signal lights
7 Pin connector
Hubs
10/7/21
Table of Contents
RC2512 Series 2
Specifications & Capacities
40-100 hp (30-75 kW)
Splitter
160 hp (119 kW)
100 hp (75 kW)
Input shaft
1 3/8" (3.5 cm) 6 Spline
1 1/2" (3.8 cm)
Splitter
4.5 pints (2.13 L) of gear lube 80-90W EP
4 pints (1.89 L) of gear lube 80-90W EP
1 1/2" (3.8 cm)
793 lbs (359.7 kg)
2,540 lbs (1152.1 kg)
Center Blades = 16,500 FPM (83.8 mps)
LP Performance hitch and swivel hitch
Standard (2,000 lbs) (907.2 kg)
12'-0" (3.66 m)
12'-7" (3.84 m)
7'-11" (2.41 m) With front cutting blade 1 1/2" (3.8 cm) off the ground.
13'-3" (4.04 m)
11" (27.9 cm)
1 1/2" to 12" (3.8 cm to 30.5 cm)
2 1/2" bore x 8" stroke hydraulic cylinder, hoses, fittings and stroke control spacers
2" bore x 8" stroke hydraulic cylinders, hoses, and fittings
o
Max. 20
down, can float up as needed as long as the wheel(s) are still on the ground.
Wing transport locks
10 Gauge (3.4 mm) deck
3/16" (5 mm) Plate
Wing deck: 1 replaceable per wing
Center deck: 2 replaceable shoes
Left wing
Counterclockwise
Counterclockwise
Right wing
Clockwise
1/2" x 3" (1.3 cm x 7.6 cm) Heat treated free swinging alloy Steel with up lift
6" (15.2 cm)
Keyed with hardened flat washer and locknut
10 Gauge (3.4 mm) round dish shaped pan, reinforced
with 1" x 3 1/2" (2.5 cm x 8.9 cm) blade bar
Single chain
Category 4 with constant velocity u-joint
Category 3 with slip-clutch
20.5" x 6.75" x 10" (52.1 cm x 17.1 cm x 25.4 cm) used aircraft tires
or 21" (53.3 cm) laminated wheels
4 - Wheels: 2 on transport axle and one on each wing axle
Spring-cushioned lift cylinder
LED
SAE J560 pin configuration
Cast iron five-bolt hubs with tapered roller bearings and 1 3/4" (4.4 cm) shafts.
Wing Blades = 16,000 FPM (81.3 mps)
RC2512 Series 2 S/N 945551+ Rotary Cutters 330-725M
49
Advertisement
Table of Contents
