SkyLink MM-318-2 User Manual

User Manual
2-Button Garage Door
Remote Contorl
Model: MM-318-2
2-Button transmitter
MM-318-2
2. PROGRAMMING
Follow one or more instructions below to program transmitter MM-318-2 to the Skylink receiver or Skylink
door opener you want to control.
2a. PROGRAMMING A REMOTE TRANSMITTER TO THE SKYLINK
1. Connect the opener to an approved power source. The
dot in the LED segment stays on.
2. Press the [Set] button for one second, and release the
button until the LED segment shows the letter "P".
3. Within 30 seconds, press any one of the buttons on the
remote that you would like to program to the opener.
4. Once the button on the remote is programmed. The
LED segment will go off and there will be one beep
indicating the programming successfully.
1. INTRODUCTION
Thank you for your purchase of Skylink remote
®
transmitter, Model MM-318-2.
The following items are included in this package:
-One of MM-318-2 Remote
-Lithium Battery CR-2032 (Installed)
-Mounting accessories
-User's instructions
® ®
garage
GARAGE DOOR OPENER - ATOMS SERIES
® TM
2b. PROGRAMMING A REMOTE TRANSMITTER TO THE SKYLINK
1. Connect the opener to an approved power source. The
dot in the LED segment stays on.
2. Press and hold the [ ] button on the wall console for 5
seconds.
3. Press and hold the [ ] button twice and the remote
icon will flash on the LCD display.
4. Within 30 seconds, press any one of the buttons on the
remote that you would like to program to the opener.
5. The garage door opener will beep if remote is
successfully programmed and the flashing remote icon
will change to solid.
2c. PROGRAMMING A REMOTE TRANSMITTER TO THE SKYLINK
To program the transmitter to the Skylink® EQ and IQ series Garage Door Opener, please follow the user's
instruction from the Garage Door Opener.
2d. PROGRAMMING A REMOTE TRANSMITTER TO THE SKYLINK SMART BUTTON
To program the transmitter to the Skylink® Smart Button
Button .
TM
2f. PROGRAMMING A REMOTE TRANSMITTER TO THE IN-CAR REMOTE SYSTEM
In order to remotely control the Skylink Garage Door Opener with your in car remote system, a transmitter must be
programmed to your in car remote system. To program the transmitter to your in car remote system, a "Learn" code
must be transmitted, follow the instructions below to transmit the "Learn" code to your in car remote system. Please
disable the password feature in the Skylink Transmitter before programming to the in-car remote system.
1. Refer to the user's instructions of your in car remote system to put your in car remote into programming mode.
2. Press and hold the button on the Skylink transmitter you already programmed for 10 seconds to program to the
car system. Release the button when the red LED changes from solid to flashing.
3. The red LED on the transmitter will be flashing for the next 20 seconds advising you to transmit the 'learn'code.
4. Once the transmitter is programmed, your in car remote system will quit from programming mode.
Your in car remote system is ready to be used.
2g. PROGRAMMING THE TRANSMITTER TO THE SKYLINKHOME
1. Set the Plug-In On/Off Control in Programming mode.
2. Turn off the connected device/light.
3. Press and hold the 'SET' button for 3 seconds, the red LED will flash.
4. Release the 'SET' button.
5. Press any one of the buttons on the transmitter that you want to program
to the receiver.
6. Once the transmitter is programmed, the red LED flashes quickly
then stops flashing. You have successfully programmed the transmitter.
GARAGE DOOR OPENER - ATOMS+ SERIES
® TM
GARAGE DOOR OPENER - EQ AND IQ SERIES
®
TM – GB-318.
, please follow the user's instruction from the Smart
TM
PLUG-IN ON/OFF CONTROL – PG-318
TM
Red LED
"SET"
button