Maintenance - DeWalt DWE46125 Instruction Manual

English

WARNING: For your own safety, read the instruction
manual for both the grinding tool and the dust
extractor vacuum before using any accessory. Failure
to heed these warnings may result in personal
injury and serious damage to the tool and the
accessory. When servicing this tool, use only identical
replacement parts.

WARNING: Hold the side handle and body of the tool
firmly to maintain control of the tool at start up and
during use and until the wheel stops rotating. Make
sure the wheel has come to a complete stop be fore
laying the tool down.

WARNING: The cutting shroud should only be
used either (1) when all four wheels are attached
and in good working condition or (2) when all four
wheels are removed and the metal base is in good
working condition.
1. Ensure all assembly and adjustment instructions have
been completed.
2. Turn the dust extractor vacuum on as instructed in the
dust extractor vacuum instruction manual.
3. Start grinder as instructed in tool instruction manual.
nOTE: Allow the tool to reach full speed before
applying to the work surface.
Proper Hand Position (Fig. I)

WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.

WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the body of the
tool and one hand on the side handle
Fig. I
28
Tuckpointing and Cutting Application
(Fig. A, I)
1. Set the desired depth of cut, see Depth of Cut
Adjustment under Assembly and Adjustments.
2. Allow the tool to reach full speed before touching it to
the work surface.
3. Position yourself so the bottom of the metal base
the wheel are facing away from you.
4. Place the metal base 3 of the shroud onto the work
surface and begin cut by plunging into the work surface.
The upper shroud will lock onto the lower shroud
9
after the initial plunge.
8
5. With the shroud oriented as shown in Figure I, push the
6. When finished with the cut, turn the tool off before
7. Push the front shroud button

MAINTENANCE


Your D
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper
tool care and regular cleaning.
Cleaning


28 .
Accessories

Recommended accessories for use with your tool
are available at extra cost from your local dealer or
authorized service center. If you need assistance in
locating any accessory, please contact D
Tool Co., 701 East Joppa Road, Towson, MD 21286, call
1-800-4-D
www.dewalt.com.
Repairs
3 and

10
nOTE: Keep the metal base of the shroud against the
work surface to ensure proper dust collection.
grinder forward along the work surface, or pull to the
left if tuckpointing.
nOTE: The grinder should ONLY be used in the
direction indicated.
removing it from work surface to limit exposure to dust.
Allow the tool to stop rotating before laying it down.
shroud and start a new plunge cut.
WARNING: To reduce the risk of serious personal
injury, turn unit off and disconnect it from
power source before making any adjustments or
removing/installing attachments or accessories.
An accidental start-up can cause injury.
WALT power tool has been designed to operate
e
WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk
of eye injury, always wear ANSI Z87.1 approved eye
protection when performing this procedure.
WARNING: Never use solvents or other harsh
chemicals for cleaning the non-metallic parts of
the tool. These chemicals may weaken the plastic
materials used in these parts. Use a cloth dampened
only with water and mild soap. Never let any liquid
get inside the tool; never immerse any part of the tool
into a liquid.
WARNING: Since accessories, other than those
offered by D WALT, have not been tested with this
e
product, use of such accessories with this tool could be
hazardous. To reduce the risk of injury, only D
recommended accessories should be used with
this product.
WALT (1-800-433-9258) or visit our website:
e
WARNING: To assure product SAFETY and
RELIABILITY, repairs, maintenance and adjustment
(including brush inspection and replacement, when
applicable) should be performed by a D
service center or a D WALT authorized service center.
e
Always use identical replacement parts.
7 to release the upper
WALT
e
WALT Industrial
e
WALT factory
e