Information; Maintenance; Specifications - Magnavox MDV260V Owner's Manual

Maintenance

Servicing Servicing
Please refer to relevant topics on the "Troubleshooting Guide"
•
on page 26 before returning the product.
If this unit becomes inoperative, do not try to correct the
•
problem by yourself. There are no user-serviceable parts inside.
Turn off, unplug the power plug, and please call our toll free
customer support line found on the cover of this manual to
locate an authorized service center.
Cleaning the Cabinet Cleaning the Cabinet
Wipe the front panel and other exterior surfaces of the unit
•
with a soft cloth.
Never use a solvent, thinner, benzene or alcohol to clean the
•
unit. Do not spray insecticide liquid near the unit. Such chemicals
may discolor the surface or damage the unit.
Cleaning Discs Cleaning Discs
When a disc becomes dirty, clean it with a cleaning cloth. Wipe
•
the disc from the center to out. Do not wipe in a circular
motion.
Do not use solvents such as benzine, thinner, commercially
•
available cleaners, detergent, abrasive cleaning agents or antistatic
spray intended for analog records.
Cleaning the Disc Lens Cleaning the Disc Lens
If this unit continues to perform improperly even after you have
•
referred to the relevant sections and to the "Troubleshooting
Guide" in this manual, the laser optical pickup unit may be
dirty. Consult your dealer or an authorized service center for
inspection and cleaning of the laser optical pickup unit.
Disc Handling Disc Handling
When you handle a disc, hold it by its edge and try not to
•
touch the surface of the disc.
Always store the disc in its protective case when not in use.
•
Do not glue paper or put stickers onto the disc. This may
•
damage the disc, and the unit may not read it correctly.

Specifications

Output signal format :
Video heads :
Tape width :
Tape speeds :
Disc media size :
Terminals :
Component video output :
Video output :
Coaxial digital audio output :
Audio output :
Video input :
Audio input :
EN

INFORMATION

INFORMATION
NTSC color
Rotary four-head
1/2 inch (12.65 mm)
SP : 1-5/16 inch/sec. (33.40 mm/sec.)
LP : 16.67 mm/sec.
SLP : 7/16 inch/sec. (11.12 mm/sec.)
5 inches (12 cm) / 3 inches (8 cm)
RCA jack x 3
Y : 1 Vp-p (75 Ω)
Pb : 700 mVp-p (75 Ω)
Pr : 700 mVp-p (75 Ω)
RCA jack x 1 1 Vp-p (75 Ω)
RCA jack x 1 500 mVp-p (75 Ω)
RCA jack x 4 2 V rms
RCA jack x 2 1 Vp-p (75 Ω)
RCA jack x 2 2 V rms
Auto Head Cleaning Auto Head Cleaning
Automatically cleans video heads as you insert or remove a
•
cassette tape, so you can see a clear picture.
If the playback picture is blurred or interrupted while the TV
•
broadcast is showing clear, the dirt may have accumulated on
the video heads, or the usage of rental or worn cassette tapes
can cause this problem. If a streaky or snowy picture appears
during playback, the video heads in your unit may need to be
cleaned.
1. Please visit your local audio/video store and purchase a
good quality VHS video head cleaner.
2. If a Video head cleaner does not solve the problem, please
call our toll free customer support line found on the cover
of this manual to locate an authorized service center.
Note:
Remember to read the instructions along with the
•
video head cleaner before use.
Clean video heads only when problems occur.
•
IR Signal Check IR Signal Check
If the remote control does not work properly, you can test if
•
the remote control sends out the infrared signal using a digital
camera (including the built-in camera of a cellular phone). It will
help to define the cause of malfunction.
Using a digital camera (including the built-in
camera of a cellular phone):
Direct a digital camera to the remote control,
press and hold a button on the remote control.
If infrared light appears on the digital camera
screen, the remote control is working.
Note:
Some cameras have an IR Filter and will not display the
•
IR signal.
Remote control :
Operating temperature :
Power requirements :
Power consumption (maximum) :
Dimensions :
Weight :
Designs and specifications are subject to change without notice.
•
If there is a discrepancy between languages, the default language
•
will be English.
Digital encoded infrared light system
41 °F (5 °C) to 104 °F (40 °C)
120 V AC +/- 10 %, 60 Hz +/- 0.5 %
16 W (standby : 2.8 W)
W : 17 3/16" (435 mm)
H : 3 3/4" (94 mm)
D : 9 3/16" (233 mm)
Approx. 5.63 lbs (2.55 kg)
27