Page 1 Foreword Congratulations on choosing a SUBARU vehicle. This Owner’s Manual has all the information necessary to keep your SUBARU in excellent condition and to properly maintain the emission control system for minimizing emission pollutants. We urge you to read this manual carefully so that you may understand your vehicle and its operation.
Page 2 This manual describes the following types of the Legacy series. 1) Legacy Sedan 2) Legacy Station wagon 3) OUTBACK Station wagon...
Page 3: Seat, Seatbelt And Srs Airbags
Warranties & Warranties for U.S.A. All SUBARU vehicles distributed by Subaru of America, Inc. and sold at retail by an authorized SUBARU dealer in the United States come with the following warranties: . SUBARU Limited Warranty . Emission Control Systems Warranty .
Page 4: Specifications
Please read these safety warnings as well as all other portions of this manual care- fully in order to gain a better understand- ing of how to use your SUBARU vehicle safely. WARNING A WARNING indicates a situation in which serious injury or death could result if the warning is ignored.
Page 5 Mark Name Child restraint lower an- chorages Child restraint top tether an- chorages Horn Windshield wiper deicer Wiper intermittent Windshield wiper and washer Windshield wiper mist (for single wipe) Rear window wiper Rear window washer Lights Parking lights, tail lights, li- cense plate lights and instru- ment panel illumination Mark...
Page 6: Child Safety
Safety precautions when driving & Seatbelt and SRS airbag WARNING . All persons in the vehicle should fasten their seatbelts BEFORE the vehicle starts to move. Other- wise, the possibility of serious injury becomes greater in the event of a sudden stop or acci- dent.
Page 7 The SRS airbag deploys with considerable speed and force and can injure or even kill chil- dren, especially if they are 12 years of age and under and are not restrained or improperly re- strained. Because children are lighter and weaker than adults, their risk of being injured from deployment is greater.
Page 8: Drinking And Driving
vehicle, have t he probl em checked and corrected as soon as possible. If you must drive under these conditions, drive only with all windows fully open. . Keep the trunk lid or rear gate closed while driving to prevent exhaust gas from entering the vehicle.
Page 9: Driving With Pets
& Modification of your vehicle CAUTION Your vehicle should not be modified other than with genuine SUBARU parts and accessories. Other types of modifications could affect its performance, safety or durability, and may even violate governmental regulations.
Page 10: California Proposition 65
& California proposition 65 warning WARNING Engine exhaust, some of its consti- tuents, and certain vehicle compo- nents contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. In addi- tion, certain fluids in vehicles and certain components of product wear contain or emit chemicals known to...
Page 11: Table Of Contents
Table of contents Seat, seatbelt and SRS airbags Keys and doors Instruments and controls Climate control Audio Interior equipment Starting and operating Driving tips In case of emergency Appearance care Maintenance and service Specifications Consumer information and Reporting safety defects Index...
Page 12 Illustrated index & Exterior Engine hood lock release (page 11-4) Headlight switch (page 3-46) Bulb replacement (page 11-50) Wiper switch (page 3-51) Moonroof (page 2-28) Roof rail (page 8-15) Door locks (page 2-5) Tire pressure (page 11-36) Flat tires (page 9-4) 10) Tire chains (page 8-13) 11) Fog light switch (page 3-49) 12) Tie-down hooks (page 9-14)
Page 13 Rear window defogger button (page 3-54) Fuel filler lid and cap (page 7-5) Child safety locks (page 2-21) Tie-down hooks (page 9-14) Towing hook (page 9-13) Trunk lid (page 2-24) Rear gate (page 2-27) Bulb replacement (page 11-53) Rear wiper switch (page 3-53) –...
Page 14 & Interior ! Passenger compartment area Lower anchorages for child restraint system (page 1-35) Seatbelt (page 1-13) Center console (page 6-6) Front seat (page 1-2) Rear seat (page 1-9)
Page 15 Top tether anchorages (page 1-38) Dome lights (page 6-2) Sun visors (page 6-4) Cargo area light (page 6-2) Rear center seatbelt (page 1-19) Cargo area cover (page 6-14) – CONTINUED –...
Page 16 Parking brake lever (page 7-44) Gear shift lever (MT) (page 7-15/ page 7-17) Selector lever (AT) (page 7-19/ page 7-25) Information display (page 3-41) Clock (page 3-41) Dashboard storage compartment (page 6-5) Navigation system (Refer to the Owner’s Manual supplement for the navigation system.) Glove box (page 6-5) Hazard warning flasher switch (page 3-5)
Page 17 & Instrument panel Door locks (page 2-5) Illumination brightness control (page 3-48) Remote control mirror (page 3-57) Windshield wiper deicer (page 3-53) Vehicle Dynamics Control OFF switch (page 7-42) Audio control buttons (page 5-26) Light control lever (page 3-46) Combination meter (page 3-5/page 3-24) Wiper control lever (page 3-49) 10) Paddle shift (page 7-28) 11) Cruise control (page 7-46)
Page 18 & Light control and wiper control levers/switches Parking light switch (page 3-48) Windshield wiper (page 3-49) Mist (page 3-51) Windshield washer (page 3-52) Rear window wiper and washer switch (page 3-53) Wiper intermittent time control switch (page 3-52) Wiper control lever (page 3-51) Light control lever (page 3-46) Front fog light switch (page 3-49) 10) Headlight ON/OFF (page 3-46)
Page 19 & Combination meter ! U.S.-spec. models (with SI-DRIVE) Temperature gauge (page 3-7) Tachometer (page 3-6) Shift-up indicator light (MT models) (page 3-38) Speedometer (page 3-6) Fuel gauge (page 3-6) Trip meter A/B selection and trip meter reset knob (page 3-10) ECO gauge (page 3-8) Selector lever and gear position indicator (AT models) (page 3-40)
Page 20 ! U.S.-spec. models (without SI-DRIVE) Temperature gauge (page 3-27) Tachometer (page 3-26) Speedometer (page 3-24) Fuel gauge (page 3-26) Trip meter A/B selection and trip meter reset knob (page 3-25) Low fuel warning light (page 3-27) Trip meter and odometer (page 3-25) Selector lever position indicator (page 3-39) Gear position indicator (page 3-39)
Page 21 ! Canada-spec. models (with SI-DRIVE) Temperature gauge (page 3-7) Tachometer (page 3-6) Shift-up indicator light (MT models) (page 3-38) Speedometer (page 3-6) Fuel gauge (page 3-6) Trip meter A/B selection and trip meter reset knob (page 3-10) ECO gauge (page 3-8) Selector lever and gear position indicator (AT models) (page 3-40) Multi-information display (page 3-9)
Page 22 ! Canada-spec. models (without SI-DRIVE) Temperature gauge (page 3-27) Tachometer (page 3-26) Speedometer (page 3-24) Fuel gauge (page 3-26) Trip meter A/B selection and trip meter reset knob (page 3-25) Low fuel warning light (page 3-27) Trip meter and odometer (page 3-25) Selector lever position indicator (page 3-39) Gear position indicator (page 3-39)
Page 23 & Warning and indicator lights Mark Name Page Seatbelt warning light 3-29 Front passenger’s 3-29 seatbelt warning light SRS airbag system 3-30 warning light CHECK ENGINE warning light/Malfunc- 3-31 tion indicator lamp Charge warning light 3-32 Oil pressure warning 3-32 light AT OIL TEMP warning 3-33...
Page 24 & Trunk/cargo area Jack handle (page 9-19) Jack (page 9-18) Spare tire (page 9-2)
Page 25 Function settings A SUBARU dealer can change the settings of the functions shown in the following table to meet your personal requirements. Contact the nearest SUBARU dealer for details. If your vehicle is equipped with the genuine SUBARU navigation system, the settings for some of these functions can be changed using the monitor.
Page 26 Item Function Battery drainage prevention Battery drainage prevention function function Seatbelt warning Sounds a chime while driving *1, *2: To have the map lights illuminate when the alarm system is triggered, it is necessary to set both *1 and *2 settings to “ON”. Possible settings Default setting Operation/Non-operation...
Page 27 1-13 Vehicle with SRS airbags and lap/shoulder 1-15 restraints for driver, front passenger, and window-side rear passengers... 1-15 SUBARU advanced frontal airbag system ... 1-15 SRS side airbag and SRS curtain airbag... 1-17 SRS airbag system monitors... 1-23 SRS airbag system servicing ...
Page 28: Front Seats
Seat, seatbelt and SRS airbags Front seats WARNING . Never adjust the seat while driv- ing to avoid the possibility of loss of vehicle control and of personal injury. . Before adjusting the seat, make sure the hands and feet of rear seat passengers or luggage are clear of the adjusting mechan- ism.
Page 29: Manual Seat
According to accident statistics, children are safer when properly restrained in the rear seating posi- tions than in the front seating posi- tions. For instructions and precau- tions concerning child restraint sys- tems, refer to the “Child restraint systems” section in this chapter. &...
Page 30: Power Seat (If Equipped)
Seat, seatbelt and SRS airbags ! Seat height adjustment (driver’s seat) The height of the seat can be adjusted by moving the seat cushion adjustment lever up and down. When the lever is pushed down, the seat is lowered. When the lever is pulled up, the seat rises. &...
Page 31: Memory Function (Driver's Seat - If Equipped)
To adjust the angle of the seatback, move the control switch. ! Seat cushion angle adjustment (driver’s seat) To adjust the seat cushion angle, pull up or push down the front end of the control switch. ! Seat height adjustment (driver’s seat) To adjust the seat height, pull up or push down the rear end of the control switch.
Page 32 Seat, seatbelt and SRS airbags 3. While pressing the “SET” button, press the desired button “1” or “2”. 4. The chirp sounds once, and the seat position is registered. ! Retrieval of seat position WARNING . Never retrieve the seat position while driving to avoid the possi- bility of loss of vehicle control and of personal injury.
Page 33: Head Restraint Adjustment
. If your vehicle is involved in a rear-end collision, have an authorized SUBARU dealer in- spect the active head restraints. . The active head restraints may not operate in the event the vehicle experiences only a slight impact in the rear.
Page 34: Lumbar Support (If Equipped)
Seat, seatbelt and SRS airbags & Lumbar support (if equipped) Pull the lever forward or backward. Pulling the lever forward will increase the amount of support for your lower back. Seat heater (if equipped) The seat heater is equipped in the front seats.
Page 35: Rear Seats
Rear seats WARNING Seatbelts provide maximum re- straint when the occupant sits well back and upright in the seat. Do not put cushions or any other materials between occupants and seatbacks or seat cushions. If you do so, the risk of sliding under the lap belt and of the lap belt sliding up over the abdomen will increase, and both can result in serious internal injury or...
Page 36: Head Restraint Adjustment
1-10 Seat, seatbelt and SRS airbags ! Sedan models Lock Unlock Release button Insert the key into the key cylinder on the seatback, unlock the seatback by turning the key counterclockwise, and then fold the seatback down while pushing the release button.
Page 37 When not used (retracted position) When used (click position) Sedan Station wagon When the seat is occupied: Raise the head restraint to the click position by pulling it up. When the seat is not occupied: To improve rearward visibility, push the head restraint down while pressing the release button on the top of the seatback.
Page 38: Armrest (If Equipped)
1-12 Seat, seatbelt and SRS airbags When the seat is occupied: Raise the head restraint to the click position by pulling it up. When the seat is not occupied: To improve rearward visibility, push the head restraint down while pressing the release button on the top of the seatback.
Page 39: Seatbelts
down while pulling the release tab. WARNING . Secure long objects properly to prevent them from shooting for- ward and causing serious injury during a sudden stop or sharp cornering. Tie long objects down with a rope or something equiva- lent.
Page 40 1-14 Seat, seatbelt and SRS airbags the rear seat properly restrained at all times. The SRS airbag deploys with considerable speed and force and can injure or even kill children, especially if they are 12 years of age and under and are not restrained or improperly restrained.
Page 41: Emergency Locking Retractor (Elr)
& Emergency Locking Retrac- tor (ELR) The driver’s seatbelt has an Emergency Locking Retractor (ELR). The emergency locking retractor allows normal body movement but the retractor locks automatically during a sudden stop, impact or if you pull the belt very quickly out of the retractor.
Page 42 For further details about canceling the warning operation, please contact your SUBARU dealer. If there is no passenger on the front passenger’s seat, the seatbelt warning device for the front passenger’s seat will be deactivated.
Page 43: Fastening The Seatbelt
If the seatbelt warning device for front passenger’s seat still does not function correctly after taking relevant corrective actions described above, immediately contact your SUBARU dealer for an inspection. & Fastening the seatbelt WARNING . Never use a belt that is twisted or reversed.
Page 44 1-18 Seat, seatbelt and SRS airbags slowly. If the belt still cannot be unlocked, let the belt retract slightly after giving it a strong pull, then pull it out slowly again. 4. Insert the tongue plate into the buckle until you hear a click. 5.
Page 45 catching the belt webbing in the door. ! Rear seatbelts (except rear center seatbelt) 1. Sit well back in the seat. 2. Pick up the tongue plate and pull the belt out slowly. Do not let it get twisted. If the belt stops before reaching the buckle, return the belt slightly and pull it out more slowly.
Page 46 1-20 Seat, seatbelt and SRS airbags WARNING Fastening the seatbelt with the web- bing twisted can increase the risk or severity of injury in an accident. When fastening the belt after it is pulled out from the retractor, espe- cially when inserting the connec- tor’s tongue plate into the mating buckle (on right-hand side), always check that the webbing is not...
Page 47 recess of the ceiling. 1. Remove the connector (tongue) plate from the slot in the recess by pulling the connector (tongue) plate. Sedan models Wagon models 2. Pull out the seatbelt slowly from the retractor. 3. After confirming that the webbing is not twisted, insert the connector (tongue) attached at the webbing end into the buckle on the right-hand side until a click...
Page 48 1-22 Seat, seatbelt and SRS airbags “CENTER” on the left-hand side until it clicks. 6. To make the lap part tight, pull up on the shoulder belt. And place the lap belt as low as possible on your hips, not on your waist.
Page 49: Seatbelt Maintenance
Wagon models 2. Allow the retractor to roll up the belt. You should hold the webbing end and guide it back into the retractor while it is rolling up. Neatly store the tongue plate in the recess and then insert the connector (tongue) plate into the slot.
Page 50: Front Seatbelt Pretensioners
SUBARU dealer. When replacing seat- belt retractor assemblies, use only genuine SUBARU parts. . If either front seatbelt does not...
Page 51: System Monitors
. If the front seatbelt retractor assem- bly or surrounding area has been damaged, contact your SUBARU dealer as soon as possible. . When you sell your vehicle, we urge you to explain to the buyer that it has seatbelt pretensioners by alerting him to the contents of this section.
Page 52: System Servicing
SRS airbag system. Immediately take your vehi- cle to your nearest SUBARU dealer to have the system checked. Unless checked and properly repaired, the seatbelt pretensioners and/or SRS airbags will operate improperly (e.g.
Page 53: Precautions Against Vehicle Modification
SUBARU dealer as soon as possible. & Precautions against vehicle modification Always consult your SUBARU dealer if you want to install any accessory parts to your vehicle. CAUTION Do not perform any of the following modifications.
Page 54 1-28 Seat, seatbelt and SRS airbags tether anchorages (LATCH)”). Children could be endangered in an accident if their child restraints are not properly secured in the vehicle. When installing the child restraint system, care- fully follow the manufacturer’s instructions. According to accident statistics, children are safer when properly restrained in the rear seating positions than in the front seating positions.
Page 55: Where To Place A Child Restraint System
& Where to place a child re- straint system The following descriptions are SUBARU’s recommendations on where to place a child restraint system in your vehicle. A: Front passenger’s seat You should not install a child restraint system (including a booster seat) due to the hazard to children posed by the passenger’s airbag.
Page 56: Choosing A Child Restraint System
1-30 Seat, seatbelt and SRS airbags WARNING S I N C E Y O U R V E H I C L E EQUIPPED WITH A PASSENGER’S SRS AIRBAG, DO NOT INSTALL A R E A R W A R D FA C I N G C H I L D SAFETY SEAT IN THE FRONT PAS- SENGER’S SEAT.
Page 57 CAUTION When you install a child restraint system, follow the manufacturer’s instructions supplied with it. After installing the child restraint system, check to ensure that it is held securely in position. If it is not held tight and secure, the danger of your child suffering personal injury in the event of an accident may be in- creased.
Page 58 1-32 Seat, seatbelt and SRS airbags 8. To remove the child restraint system, press the release button on the seatbelt buckle and allow the belt to retract completely. The belt will return to the ELR mode. WARNING NEVER INSTALL A REARWARD FA- CING CHILD SEAT IN THE FRONT PASSENGER’S SEAT.
Page 59 6. Before having a child sit in the child restraint system, move it back and forth and right and left to check if it is firmly secured. Sometimes a child restraint can be more firmly secured by pushing it down into the seat cushion and then tightening the seatbelt.
Page 60: Installing A Booster Seat
1-34 Seat, seatbelt and SRS airbags & Installing a booster seat WARNING . Child restraint systems and seat- belts can become hot in a vehicle that has been closed up in sunny weather; they could burn a small child. Check the child restraint system before you place a child in it.
Page 61: Installation Of Child Restraint Systems By Use Of Lower And Tether Anchorages (Latch)
. Never place the shoulder belt under the child’s arm or behind the child’s back. If an accident occurs, this can increase the risk or severity of injury to the child. . The seatbelt should fit snugly in order to provide full restraint. Loose fitting belts are not as effective in preventing or redu- cing injury.
Page 62 1-36 Seat, seatbelt and SRS airbags Your vehicle is equipped with four lower anchorages (bars) and three upper an- chorages (tether anchorages) for accom- modating such child restraint systems. The lower anchorages (bars) are used for installing a child restraint system only on the rear seat window-side seating posi- tions.
Page 63 rear seat seatbacks. These marks indicate the positions of the lower anchorages (bars). Each lower anchorage is located behind the cover of seatback bottom. CAUTION When you install a child restraint system, follow the manufacturer’s instructions supplied with it. After installing the child restraint system, check to ensure that it is held securely in position.
Page 64: Top Tether Anchorages
If you have any question concerning this type of child restraint system, ask your SUBARU dealer. & Top tether anchorages Your vehicle is equipped with three top tether anchorages so that a child restraint system having a top tether can be installed in the rear seat.
Page 65 ! To hook the top tether ! Sedan 1. Remove the head restraint at the seating position where the child seat has been installed with the seatbelt or lower anchorages; lift up the head restraint while pressing the release button. Store the head restraint in the trunk.
Page 66: Srs Airbag (Supplemental Restraint System Airbag)
1-40 Seat, seatbelt and SRS airbags seating position where the child restraint system has been installed with the seat- belt or lower anchorages; lift up the head restraint while pressing the release button. Store the head restraint in the cargo area. Avoid placing the head restraint in the passenger compartment to prevent it from being thrown around in the passenger...
Page 67 gers) These SRS airbags are designed only as a supplement to the primary protec- tion provided by the seatbelt. The system also controls front seatbelt pretensioners. For operation instructions and precautions concerning the seatbelt pretensioner, refer to the “Front seatbelt pretensioners”...
Page 68 1-42 Seat, seatbelt and SRS airbags WARNING . Put children aged 12 and under in the rear seat properly restrained at all times. The SRS airbag deploys with considerable speed and force and can injure or even kill children, especially if they are 12 years of age and under and are not restrained or improperly restrained.
Page 69 ! Components Sedan Airbag control module (including impact sensors) Frontal airbag module (driver’s side) Frontal airbag module (front passenger’s side) Front sub sensor (left-hand side) Front sub sensor (right-hand side) Side airbag module (driver’s side) Side airbag module (front passenger’s side) 1-43 Seat, seatbelt and SRS airbags...
Page 70 1-44 Seat, seatbelt and SRS airbags Station wagon Airbag control module (including impact sensors) Frontal airbag module (driver’s side) Frontal airbag module (front passenger’s side) Front sub sensor (left-hand side) Front sub sensor (right-hand side) Side airbag module (driver’s side) Side airbag module (front passenger’s side) Side airbag sensor (center pillar left-hand...
Page 71: Subaru Advanced Frontal Airbag System
& SUBARU advanced frontal airbag system Your vehicle is equipped with a SUBARU advanced frontal airbag system that com- plies with the new advanced frontal airbag requirements in the amended Federal Motor Vehicle Safety Standard (FMVSS) No. 208. The SUBARU advanced frontal airbag system automatically determines the de- ployment force of the driver’s SRS frontal...
Page 72 1-46 Seat, seatbelt and SRS airbags WARNING Never hold a child on your lap or in your arms. The SRS airbag deploys with considerable force and can injure or even kill the child. WARNING The SRS airbag deploys with con- siderable speed and force.
Page 73 SRS frontal airbag even when the driver’s SRS frontal airbag deploys. This is normal. Observe the following precautions. Failure to do so may prevent the SUBARU advanced frontal airbag system from functioning correctly or cause the system to fail.
Page 74 Seat, seatbelt and SRS airbags passenger’s occupant detection system have failed, the SRS airbag system warning light will illuminate. Have the system inspected by your SUBARU deal- er immediately if the SRS airbag system warning light illuminates. If your vehicle has sustained impact, this may affect the proper function of the SUBARU advanced frontal airbag system.
Page 75 that follows.) . The seat is equipped with a booster seat and a small child is in the booster seat. (See WARNING that follows.) . The seat is relieved of the occupant load for a time exceeding the predeter- mined monitoring time period. .
Page 76 OFF indicator extinguishes after taking relevant corrective actions described above, relocate the child restraint system to the rear seat and immediately contact your SUBARU dealer for an inspection. NOTE When a child who has outgrown a child restraint system or a small adult is seated in the front passenger’s seat,...
Page 77 SUBARU advanced air- bag system. If you have any questions, you may contact the following SUBARU distributors: <Continental U.S., Alaska and the District...
Page 78 Driver’s side Passenger’s side The SRS airbag can function only when the ignition switch is in the “ON” position. The SUBARU advanced frontal airbag system is designed to determine the activation or deactivation condition of the front passenger’s SRS frontal airbag depending on the total load on the front passenger’s seat monitored by the front...
Page 79 The driver’s SRS frontal airbag and front passenger’s SRS frontal airbag are de- signed to deploy in the event of an accident involving a moderate to severe frontal collision. It is basically not designed to deploy in lesser frontal impacts be- cause the necessary protection can be achieved by the seatbelt alone.
Page 80: Seat, Seatbelt And Srs Airbags
1-54 Seat, seatbelt and SRS airbags both driver’s and front passenger’s SRS frontal airbags may be activated when the vehicle sustains a hard impact in the undercarriage area from the road surface (such as when the vehicle plunges into a deep ditch, is severely impacted or knocked hard against an obstacle on the road such as a curb).
Page 81 ! Examples of the types of accidents in which deployment of the driver’s/driver’s and front passenger’s SRS frontal airbag(s) is unlikely to occur. 1-55 Seat, seatbelt and SRS airbags The vehicle strikes an object, such as a telephone pole or sign pole. The vehicle slides under the load bed of a truck.
Page 82: Srs Side Airbag And Srs Curtain Airbag
1-56 Seat, seatbelt and SRS airbags ! Examples of the types of accidents in which the driver’s/driver’s and front passenger’s SRS frontal airbag(s) will basically not deploy. The driver’s and front passenger’s SRS frontal airbags are designed basically not to deploy if the vehicle is struck from the side or from behind, or if it rolls onto its side or roof, or if it is involved in a low- speed frontal collision.
Page 83 WARNING The SRS side airbag and SRS curtain airbag are designed as only a supplement to the primary protec- tion provided by the seatbelt. They do not do away with the need to fasten seatbelts. It is also important to wear your seatbelt to help avoid injuries that can result when an occupant is not seated in a proper upright position.
Page 84 1-58 Seat, seatbelt and SRS airbags WARNING . Never allow a child to kneel on the front passenger’s seat facing the side window or to wrap his/ her arms around the front seat seatback. In the event of an accident, the force of the SRS side airbag deployment could injure the child seriously be- cause his/her head or arms or...
Page 85 A hands-free microphone or other accessory in such a loca- tion could be propelled through the cabin with great force by the curtain airbag, or it could prevent correct deployment of the curtain airbag. In either case, the result could be serious injuries. .
Page 86 1-60 Seat, seatbelt and SRS airbags impact force, is located under the rear center seat. If one of the center pillar impact sensors and the impact sensor that is located under the rear center seat together sense an impact force above a predetermined level in a side collision, the control module causes both the SRS side airbag and curtain airbag on the impacted side to...
Page 87 ! Example of the type of accident in which the SRS side airbag and SRS curtain airbag will most likely de- ploy. A severe side impact near the front seat activates the SRS side airbag and SRS curtain airbag. 1-61 Seat, seatbelt and SRS airbags –...
Page 88 1-62 Seat, seatbelt and SRS airbags ! Examples of the types of accidents in which the SRS side airbag and SRS curtain airbag are unlikely to deploy. The vehicle is involved in an oblique side-on impact. The vehicle is involved in a side-on impact in an area outside the vicinity of the passenger compartment.
Page 89: Srs Airbag System Monitors
! Examples of the types of accidents in which the SRS side airbag and SRS curtain airbag will basically not deploy. The vehicle is involved in frontal collision with another vehicle (moving or station- ary). The vehicle is struck from behind. The SRS side airbag and SRS curtain airbag are basically not designed to deploy if the vehicle is involved in a frontal...
Page 90 SRS airbag system. Immediately take your vehi- cle to your nearest SUBARU dealer to have the system checked. Unless checked and properly repaired, the seatbelt pretensioners and/or SRS airbags will operate improperly (e.g.
Page 91: Srs Airbag System Servicing
. Under the rear center seat In the event that the SRS airbag is deployed, replacement of the system should be performed only by an author- ized SUBARU dealer. When the compo- nents of the SRS airbag system are replaced, use only genuine SUBARU 1-65 Seat, seatbelt and SRS airbags parts.
Page 92: Precautions Against Vehicle Modification
Manual. . Attachment of any equipment (side steps or side sill protectors, etc.) other than genuine SUBARU accessory parts to the side body. Always consult your SUBARU dealer if you want to install any accessory parts on your vehicle.
Page 93 Keys ... Key number ... Immobilizer ... Security ID plate... Security indicator light ... Key replacement ... Door locks ... Locking and unlocking from the outside ... Locking and unlocking from the inside ... Battery drainage prevention function ... Power door locking switches ... Key lock-in prevention function ...
Page 94: Keys And Doors
Keys and doors Keys Master key Submaster key Valet key Key number plate Security ID plate Three types of keys are provided for your vehicle. Master key, submaster key and valet key. The master key and submaster key fit all locks on your vehicle.
Page 95: Immobilizer
Immobilizer The immobilizer system is designed to prevent an unauthorized person from starting the engine. Only keys registered with your vehicle’s immobilizer system can be used to operate your vehicle. Even if an unregistered key fits into the ignition switch and can be turned to the “START” position, the engine will automatically stop after several seconds.
Page 96: Security Indicator Light
If the security indicator light does not flash, the immobilizer system may be faulty. If this occurs, contact your SUBARU dealer as soon as possible. In case an unauthorized key is used (e.g. an imitation key), the security indicator light illuminates.
Page 97: Door Locks
Door locks & Locking and unlocking from the outside To lock the driver’s door from the outside with the key, turn the key toward the rear. To unlock the door, turn the key toward the front. Lift the outside door handle to open an unlocked door.
Page 98: Locking And Unlocking From The Inside
Keys and doors & Locking and unlocking from the inside WARNING Keep all doors locked when you drive, especially when small chil- dren are in your vehicle. Along with the proper use of seat- belts and child restraints, locking the doors reduces the chance of being thrown out of the vehicle in an accident.
Page 99: Power Door Locking Switches
SUBARU dealer. Contact the nearest SUBARU dealer if you would like to change the setting. NOTE . The factory setting (default setting) for this function is set as “operational”. . When leaving the vehicle, please...
Page 100: Remote Keyless Entry System
This function’s operational/non-opera- tional setting can be changed. Vehicle with genuine SUBARU naviga- tion system: The operational/non-operational setting can be changed using the monitor. For details, please refer to the Owner’s Man- ual supplement for the monitor system.
Page 101: Locking The Doors
The transmitter for the remote keyless entry system is located inside the key head. The remote keyless entry system has the following functions. . Locking and unlocking the doors (and rear gate on the Station wagon) without a . Locking and unlocking the doors (and trunk lid on the Sedan) without key .
Page 102: Unlocking The Doors
2-10 Keys and doors & Unlocking the doors Press the “ ” button to unlock the driver’s door. An electronic chirp will sound twice and the turn signal lights will flash twice. To unlock all doors and the rear gate (Station wagon), briefly press the “...
Page 103: Sounding A Panic Alarm
Replace the battery as soon as possible. The battery can be replaced by your authorized SUBARU dealer. If you replace the battery by yourself, use utmost care that no dust, oil or water enters the transmitter.
Page 104 2-12 Keys and doors To replace the battery: 1. Remove the screw on the key head. 2. Open the key head using a flat-head screwdriver. 3. Remove the transmitter case from the key head. 4. Open the transmitter case by releasing the hooks.
Page 105: Replacing Lost Transmitters
& Replacing lost transmitters If you lose a transmitter or want to purchase additional transmitters (up to four can be programmed), you should re- program all of your transmitters for secur- ity reasons. It is recommended that you have your dealer program all of your transmitters into your system.
Page 106 2-14 Keys and doors LOCK (2) Insert the key into the ignition switch, then turn it from the “LOCK” position to the “ON” position 10 times within 15 seconds. NOTE . When you complete step (2), an electronic tone will sound once. .
Page 107 LOCK” side within 5 seconds. NOTE . An electronic tone will sound. . If you pull the lock knob to the “UNLOCK” side when more than 5 seconds have passed, an error will occur. In this event, perform the proce- dure again beginning with part 4.
Page 108: Alarm System
The map lights and dome light notification is deactivated as the fac- tory setting. Refer to the “Function settings” section that is mentioned earlier in this manual. A SUBARU deal- er can activate the system. Contact your SUBARU dealer for details. & Activating and deactivating the alarm system To change the setting of your vehicle’s...
Page 109: If You Have Accidentally Triggered The Alarm System
NOTE You may have the above setting change done by your SUBARU dealer. & If you have accidentally trig- gered the alarm system ! To stop the alarm Do any of the following operations: .
Page 110 . The 30-second standby time can be eliminated if you prefer. Have it per- formed by your SUBARU dealer. . If your vehicle is a Sedan and you unlock the trunk using the remote transmitter’s “...
Page 111: Disarming The System
DOORS MUST BE MANUALLY LOCKED. ! To enter the passive mode If you wish to program the passive arming mode, have it done by your SUBARU dealer. ! Arming the system CAUTION In passive mode, the system will...
Page 112: Tripped Sensor Identification
2-20 Keys and doors position. LOCK 2. Turn the ignition switch from “ON” to “LOCK” position and remove the key from the ignition switch. 3. Open the doors and get out of the vehicle. 4. Before closing the doors, lock all doors with the inside door lock levers.
Page 113: Child Safety Locks
30 seconds. If you desire, your SUBARU dealer can connect them and set them for activation or deactivation. NOTE . The shock sensors are not always...
Page 114 2-22 Keys and doors ! Driver’s side switches Lock switch For driver’s window For front passenger’s window For rear left passenger’s window For rear right passenger’s window All door windows can be controlled by the power window switch cluster at the driver side door.
Page 115 To open: Push the appropriate switch down and hold it until the window reaches the desired position. To close: Pull the switch up and hold it until the window reaches the desired position. ! Locking the passengers’ windows To lock: Push the lock switch.
Page 116: Trunk Lid (Sedan)
2-24 Keys and doors Rear passengers’ window switches Open Close To close: Pull the switch up and hold it until the window reaches the desired position. When the lock switch on the power window switch cluster, located on the driver’s side door, is in the “LOCK” position, the passengers’...
Page 117: To Lock And Unlock The Trunk Lid Release Lever
& To lock and unlock the trunk lid release lever When you entrust your vehicle key to another person, you can lock the trunk lid release lever to prevent luggage in the trunk from being stolen. To lock the trunk lid release lever, insert the master key or submaster key into the key cylinder at the rear of the release lever and turn it...
Page 118 In that case, use the key to release the latch, then close the trunk lid. Also, if the movement of the release handle feels restricted or not entirely smooth during operation, or the handle and/or handle base is cracked, contact your SUBARU dealer.
Page 119: Rear Gate (Station Wagon)
Rear gate (Station wagon) The rear gate can be locked and unlocked using either the remote keyless entry system or power door locking switch. Refer to the “Power door locking switches” and “Remote keyless entry system” sec- tion in this chapter. To open: First unlock the rear gate lock then pull the outside handle up.
Page 120: Moonroof (If Equipped)
2-28 Keys and doors NOTE If the rear gate cannot be unlocked due to a discharged battery of the vehicle, a malfunction in the door locking/unlock- ing system or other causes, you can unlock it by manually operating the rear gate lock release lever. For the procedure, refer to the “Rear gate (Station wagon) –...
Page 121: Tilting/Sliding Moonroof (Sedan)
& Tilting/sliding moonroof (Sedan) ! Tilt function Tilt up Tilt down The tilting function will only operate when the moonroof is fully closed. Push the rear side of the “Tilt” switch to raise the moonroof. Push the front side of the “Tilt” switch to lower the moonroof.
Page 122: Moonroof (Station Wagon)
2-30 Keys and doors NOTE For the sake of safety, it is recom- mended that you avoid driving with the moonroof fully opened. ! Sun shade The sun shade can be slid forward or backward by hand while the moonroof is closed.
Page 123 switch to the “CLOSE” side then quickly release it. The rear moonroof will stop at a position approximately 5.9 in (15 cm) before its fully closed position. After confirming safety, pull the switch to the “CLOSE” side again and quickly release it. The rear moonroof will fully close.
Page 124: Abs Warning Light
Odometer and trip meter ... Current and average fuel consumption ... Outside temperature and journey time ... Driving range on remaining fuel... Clock (vehicle with genuine SUBARU navigation system)... SI-DRIVE display ... Meter settings ... Warning messages and driver’s information...
Page 125 Cruise control indicator light ... Cruise control set indicator light... Headlight indicator light ... Front fog light indicator light (if equipped) ... Clock (vehicle without genuine SUBARU navigation system)... 3-41 Information display (2.5 L non-turbo model without genuine SUBARU navigation system) ...
Page 126: Ignition Switch
Ignition switch WARNING . Never turn the ignition switch to “LOCK” while the vehicle is being driven or towed because that will lock the steering wheel, preventing steering control. And when the engine is turned off, it takes a much greater effort than usual to steer.
Page 127: Acc
Instruments and controls ! Manual transmission vehicles The key can be turned from “Acc” to “LOCK” only when the key is pushed in while turning it. & Acc In this position the electrical accessories (radio, accessory power outlet, etc.) can be used.
Page 128: Key Reminder Chime
& Key reminder chime The reminder chime sounds when the driver’s door opens and the key is in the “LOCK” or “Acc” positions. The chime stops when the key is removed from the ignition switch. & Ignition switch light For easy access to the ignition switch in the dark, the ignition switch light illumi- nates when any of the doors are opened.
Page 129: Speedometer
Instruments and controls ignition switch to start the engine. This is not an indication of a problem. & Speedometer The speedometer shows the vehicle speed. & Tachometer The tachometer shows the engine speed in thousands of revolutions per minute. CAUTION Do not operate the engine with the pointer of the tachometer in the red zone.
Page 130: Temperature Gauge
NOTE You will see the “ ” sign in the fuel gauge. This indicates that the fuel filler door (lid) is located on the right side of the vehicle. ! Low fuel warning light Low fuel warning light The low fuel warning light illuminates when the tank is nearly empty [Approxi- mately 2.6 US gal (10 liters, 2.2 lmp gal)].
Page 131: Eco Gauge
Instruments and controls We recommend that you drive moderately until the pointer of the temperature gauge reaches near the middle of the range. Engine operation is optimum with the engine coolant at this temperature range. And high revving operation while the engine is not warmed up enough should be avoided.
Page 132: Multi-Information Display
Multi-information display (vehicle with SI-DRIVE) & Display & Operation switch CAUTION To ensure safety, do not attempt to change the function of the indicator during driving, as an accident could result. Next (up) Information display Back (down) Use the “ ”...
Page 133: Odometer And Trip Meter
3-10 Instruments and controls & Odometer and trip meter ! Odometer U.S.-spec. models Canada-spec. models This indication shows the total distance that the vehicle has been driven. If you press the trip knob when the ignition switch is in the “LOCK” or “Acc” position, the odometer/trip meter will light up.
Page 134: Current And Average Fuel Consumption
off. NOTE If the connection between the combina- tion meter and battery is broken for any reason such as vehicle maintenance or fuse replacement, the data recorded on the trip meter will be lost. & Current and average fuel consumption U.S.-spec.
Page 135: Outside Temperature And Journey Time
3-12 Instruments and controls & Outside temperature and journey time ! Outside temperature U.S.-spec. models Canada-spec. models Outside temperature Journey time The indicator shows the outside tempera- ture in a range from −22 to 1228F (−30 to 508C). The indicator can give a false reading under any of the following conditions: .
Page 136 NOTE The outside temperature indication may differ from the actual outside temperature. The indication “OUT TEMP 378F (38C)” should be treated only as a guide. Be sure to check the condition of the road surface before driving. ! Journey time U.S.-spec.
Page 137: Driving Range On Remaining Fuel
3-14 Instruments and controls & Driving range on remaining fuel U.S.-spec. models Canada-spec. models The driving range indicates the distance in units of 10 miles (10 km) that can be driven by taking into consideration the fuel remaining in the tank and the average rate of fuel consumption over the last 30 miles (30 km).
Page 138: Clock (Vehicle With Genuine Subaru Navigation System)
& Clock (vehicle with genuine SUBARU navigation system) The clock receives the correct time from the navigation system. To adjust the time shown by the clock, refer to the Owner’s Manual supplement for the monitor sys- tem and adjust the time of the navigation system.
Page 139 3-16 Instruments and controls To change the current setting, take the following steps. 1. Within 12 seconds after turning on the ignition switch, press the “ /SET” switch for at least 2 seconds. 2. T h e d i s p l a y s h o w s “ M E T E R SETTING”, and then changes to the setting screen.
Page 140 tial illumination when regular illumina- tion (for driving) has begun. ! Date/Time settings The following items can be set or regis- tered in the “Date/Time” setting menu. . Present date & time . Birthday . Anniversary NOTE To enter “Birthday” and “Anniversary”, “Present date &...
Page 141 3-18 Instruments and controls 2. Select an item that you desire to set with “ ” and “ ”, and press “ /SET”. 3. Select a value for the setting item with “ ” and “ ”, and confirm the setting with “...
Page 142 From a week before to the day before On the date that was set ! Anniversary 1. Press “ ” or “ ” until “Anniversary” is displayed and press “ /SET”. 2. Select an item that you desire to set with “...
Page 143: Warning Messages And Driver's Information
3-20 Instruments and controls On the date that was set ! Clear all dates 1. Press “ ” or “ ” until “Clear all dates” is displayed and press “ /SET”. 2. Select “YES” or “NO” and press “ / SET”.
Page 144: Instruments And Controls
3-21 Instruments and controls Canada-spec. models The display shows the interruptive mes- sage for 3 seconds and then returns to its original display. At this time, the specified warning message leaves the “ ” mark on the lower left side of the display. When the “...
Page 145 This warning message indicates a malfunction of the “SI-DRIVE mode” change. If this warning message is shown on the display, contact your nearest SUBARU dealer and have the SI-DRIVE mode system inspected. The display shows the interruptive warning message for 3 seconds.
Page 146 3-23 Instruments and controls Driver’s information Details Low temperature information This message is displayed when the outside temperature is 378F (38C). When this message appears on the display, be careful because the road surface may be frozen. For details of this indication, refer to the “ Outside temperature and journey time”...
Page 147: Meters And Gauges (Vehicle Without Si-Drive)
3-24 Instruments and controls Meters and gauges (vehicle without SI-DRIVE) NOTE Liquid-crystal displays are used in some of the meters and gauges in the combination meter. You will find their indications hard to see if you wear polarized glasses. & Combination meter illumina- tion When the ignition switch is turned to the “ON”...
Page 148: Odometer
& Odometer This meter displays the odometer when the ignition switch is in the “LOCK”, “Acc” or “ON” position. The odometer shows the total distance that the vehicle has been driven. If you press the trip knob when the ignition switch is in the “LOCK”...
Page 149: Tachometer
“ ”. If the trip meter shows “ ”, immediately contact the nearest SUBARU dealer and have the vehicle communication system inspected. NOTE If you press the trip knob while the trip meter is showing “...
Page 150: Temperature Gauge
seconds or (b) open and close the driver’s door, the fuel gauge needle will drop to the “E” position and the dial and needle will go off. NOTE You will see the “ ” sign in the fuel gauge. This indicates that the fuel filler door (lid) is located on the right side of the vehicle.
Page 151: Warning And Indicator Lights
3-28 Instruments and controls accordance with the outside temperature and driving conditions. We recommend that you drive moderately until the pointer of the temperature gauge reaches near the middle of the range. Engine operation is optimum with the engine coolant at this temperature range. Also, high revving operation while the engine is not sufficiently warmed up should be avoided.
Page 152: Seatbelt Warning Light And Chime
If any lights fail to illuminate, it indicates a burned-out bulb or a malfunction of the corresponding system. Consult your authorized SUBARU dealer for repair. & Seatbelt warning light and chime Your vehicle is equipped with a seatbelt warning device at the driver’s and front passenger’s seat, as required by current...
Page 153: Srs Airbag System Warning Light
If still the seatbelt warning device for front passenger’s seat does not function cor- rectly after taking relevant corrective ac- tions described above, immediately con- tact your SUBARU dealer for an inspec- tion. & SRS airbag system warning light When the ignition switch is turned to the “ON”...
Page 154: Front Passenger's Frontal Airbag On And Off
3-31 Instruments and controls of the indicators illuminates depending on the status of the front passenger’s SRS frontal airbag determined by the SUBARU advanced frontal airbag system monitor- ing. If the front passenger’s SRS frontal airbag is activated, the passenger’s frontal airbag ON indicator will illuminate while the OFF indicator will remain extinguished.
Page 155: Charge Warning Light
The CHECK ENGINE warning light/mal- function indicator lamp may stop blinking and illuminate steadily after several driv- ing trips. You should have your vehicle checked by an authorized SUBARU deal- er immediately. & Charge warning light If this light illuminates when the engine is running, it may indicate that the charging system is not working properly.
Page 156: At Oil Temp Warning Light (At Models)
TPMS to continue to function properly. Should the warning light illuminate stea- dily after blinking for approximately one minute, have the system inspected by your nearest SUBARU dealer as soon as possible. – CONTINUED –...
Page 157: Abs Warning Light
ON or the light illuminates steadily after blinking for approxi- mately one minute, you should have your Tire Pressure Monitoring Sys- tem checked at a SUBARU dealer as soon as possible. If this light illuminates while driving, never brake suddenly and keep driving straight ahead while gradu- ally reducing speed.
Page 158: Brake System Warning Light
If the fluid level is below the “MIN” mark in the reservoir, do not drive the vehicle. Have the vehicle towed to the nearest SUBARU dealer for repair. ! Electronic Brake Force Distribution (EBD) system warning...
Page 159: Low Fuel Warning Light
3. Release the parking brake. If both warning lights go out, the EBD system may be faulty. Drive carefully to the nearest SUBARU dealer and have the system inspected. 4. If both warning lights illuminate again and stay illuminated after the engine has...
Page 160: Light (If Equipped)
You will be safe while driving with this condition, but have your vehicle checked at a SUBARU dealer as soon as possible. NOTE If the warning light behavior is as...
Page 161: Security Indicator Light
The Vehicle Dynamics Control system is probably faulty under the following condi- tion. Have your vehicle checked at a SUBARU dealer as soon as possible. . The light does not go out even after the lapse of several minutes (the engine has warmed up) after the engine has started.
Page 162: S# Prep Indicator Light (Vehicle With Si-Drive)
& S# PREP indicator light (vehicle with SI-DRIVE) S# PREP indicator light When the engine is not warmed up sufficiently, the S# PREP indicator light turns on. While this indicator light is on, the SI-DRIVE mode cannot be changed to the Sport Sharp (S#) mode.
Page 163: Selector Lever And Gear Position Indicator (At Models) (If Equipped)
. If this indicator light and the CHECK ENGINE warning light/malfunction in- dicator lamp flash simultaneously dur- ing driving, have the vehicle checked by your nearest SUBARU dealer. & Cruise control set in- dicator light The cruise control set indicator light illuminates when the ignition switch is turned to the “ON”...
Page 164: Clock (Vehicle Without Genuine Subaru Navigation System)
NOTE . If your vehicle is a 2.5 L non-turbo model equipped with the genuine SUBARU navigation system, refer to the Owner’s Manual supplement for the navigation system. . If your vehicle is a turbo model or a 3.0 L model equipped with the genuine SUBARU navigation system, refer to the “Clock (vehicle with genuine...
Page 165: Outside Temperature Indicator
3-42 Instruments and controls & Outside temperature indica- U.S.-spec. models Canada-spec. models The outside temperature indicator shows the outside temperature in a range from −22 to 1228F (−30 to 508C). The indicator can give a false reading under any of the following conditions: .
Page 166: Current Fuel Consumption
378F (38C) or lower, the temperature indication flashes to show that the road surface may be frozen. If the outside temperature drops to 378F (38C) or lower while the display is giving an indication other than the outside temperature, the display switches to the outside temperature indication and flashes for 5 seconds before returning to its original indication.
Page 167: Driving Range On Remaining Fuel
3-44 Instruments and controls last reset. Pressing the trip knob toggles the indica- tion between the average fuel consump- tion corresponding to the A trip meter indication and the average fuel consump- tion corresponding to the B trip meter indication. When either of the trip meter indications is reset, the corresponding average fuel consumption value is also reset.
Page 168: Journey Time
Canada-spec. models If the driving range is shown as “ there is only a tiny amount of fuel left in the tank. You must refuel the vehicle immedi- ately. NOTE The driving range on remaining fuel is only a guide. The indicated value may differ from the actual driving range on remaining fuel, so you must immedi- ately fill the tank when the low fuel...
Page 169: Light Control Switch
3-46 Instruments and controls Light control switch WARNING To prevent battery discharge result- ing from accidentally leaving your lights on when your vehicle is parked, the light switch operates only when the ignition switch is in the “ON” position. In any other position, the vehicle’s lights will be out.
Page 170: Headlight Flasher
& Headlight flasher CAUTION Do not hold the lever in the flashing position for more than just a few seconds. To flash the headlights, pull the lever toward you and then release it. The high beam will stay on for as long as you hold the lever.
Page 171: Illumination Brightness Control
3-48 Instruments and controls Illumination brightness con- trol The brightness of clock display, audio, air conditioner, information display and meter/ gauge illumination dims when the light switch is in the “ ” or “ ” position. You can adjust brightness of the meter/gauge illumination for better visibility.
Page 172: Front Fog Light Switch (If Equipped)
Front fog light switch (if equipped) The front fog lights operate only when the light switch is in the “ ” position. However, the front fog lights turn off when the headlights are switched to high beam. To turn on the front fog lights, turn the front fog light switch on the turn signal lever upward to the “...
Page 173 . Use clean water if windshield washer fluid is unavailable. In areas where water freezes in winter, use SUBARU Windshield Washer Fluid or the equivalent. Refer to the “Windshield washer fluid” section in chapter 11. Also, when driving the vehicle...
Page 174: Windshield Wiper And Washer Switches
& Windshield wiper and washer switches The wiper operates only when the ignition switch is in the “ON” or “Acc” position. ! Windshield wipers Station wagon Sedan OFF : Park : Intermittent LO: Low speed HI: High speed To turn the wipers on, push the wiper control lever down.
Page 175 3-52 Instruments and controls you release the lever. ! Wiper intermittent time control Station wagon Sedan When the wiper switch is in the “ position, turn the dial to adjust the operat- ing interval of the wiper. The operating interval can be adjusted in nine steps from the shortest interval to the longest.
Page 176: Rear Window Wiper And Washer Switch (Station Wagon)
& Rear window wiper and washer switch (Station wa- gon) : Washer (accompanied by wiper operation) ON: Continuous INT: Intermittent OFF: Park : Washer ! Rear wiper To turn the rear wiper on, turn the knob on the end of the wiper control lever upward to the “INT”...
Page 177: Rear Window Defogger Button
If you wish, you can set the windshield wiper deicer for continuous operation. . Vehicle with genuine SUBARU navi- gation system: The windshield wiper deicer setting can be changed for continuous operation by means of the monitor.
Page 178 For the vehicle with the automatic climate control system, if you wish, you can set the rear window defogger for continuous operation as follows. . Vehicle with genuine SUBARU navi- gation system: The rear window defogger setting can be changed for continuous operation by means of the monitor.
Page 179: Mirrors
3-56 Instruments and controls Mirrors Always check that the inside and outside mirrors are properly adjusted before you start driving. & Inside mirror The inside mirror has a day and night position. Pull the tab at the bottom of the mirror toward you for the night position.
Page 180: Outside Mirrors
other similar items. Periodically wipe the sensors clean using a piece of dry soft cotton cloth or an applicator. ! Compass calibration 1. For optimum calibration, switch off all nonessential electrical accessories (rear window defogger, heater/air conditioning system, spotlight, etc.) and ensure all doors are shut.
Page 181 3-58 Instruments and controls ! Outside mirror defogger (if equipped) Vehicle with manual climate control sys- Vehicle with automatic climate control system The outside mirror defogger shares the button with rear window defogger. The outside mirror defogger operates only when the ignition switch is in the “ON” position.
Page 182: Tilt/Telescopic Steering Wheel
Tilt/telescopic steering wheel WARNING . Do not adjust the steering wheel tilt/telescopic position while driv- ing. This may cause loss of vehicle control and result in personal injury. . If the lever cannot be raised to the fixed position, adjust the steering wheel again.
Page 183: Climate Control
Ventilator... Air flow selection ... Center and side ventilators ... Manual climate control system (if equipped) ... Control panel ... Heater operation ... Air conditioner operation... Automatic climate control system (if equipped) ... Control panel ... Temperature sensors... Operating tips for heater and air conditioner...
Page 184: Climate Control
Climate control Ventilator & Air flow selection...
Page 185: Center And Side Ventilators
& Center and side ventilators ! Center ventilators Move the tab up and down or right and left to adjust the flow direction. ! Side ventilators Open Close Move the tab up and down or right and left to adjust the flow direction. To open the ventilator, turn the side grille open/close wheel upward to the “...
Page 186 Climate control ! Temperature control dial This dial regulates the temperature of air flow from the air outlets over a range from the blue side (cool) to red side (warm). ! Fan speed control dial The fan operates only when the ignition switch is turned to the “ON”...
Page 187: Heater Operation
! Air conditioner button The air conditioner operates only when the engine is running. Push the air conditioner button while the fan is in operation to turn on the air conditioner. The indicator light will illumi- nate. Push it again to turn off the air conditioner. ! Air inlet selection button ON position (Recirculation): Interior air is recirculated inside the vehicle.
Page 188 Climate control illuminate. At the same time, the air inlet selection is automatically set to “outside air” mode. In this state, you cannot select “recir- culation” mode by manually pressing the air inlet selection button. Also, you cannot stop the air condi- tioner compressor by pressing the air conditioner button.
Page 189: Air Conditioner Operation
2. Set the air flow control dial to the “ ” position. 3. Set the temperature control dial all the way left. 4. Set the fan speed control dial to the desired speed. When driving on a dusty road, set the air inlet control button to the ON position.
Page 190: Control Panel
Climate control & Control panel AUTO button Temperature control dial (driver’s side) Defroster button Temperature control dial (passenger’s side) Rear window defogger button (Refer to the “Rear window defogger button” sec- tion in chapter 3.) Air conditioner button Air flow mode selection button Fan speed control button Air inlet selection button 10) OFF button...
Page 191 ! Temperature control dial Driver’s side Passenger’s side It is possible to make separate tempera- ture settings for the driver’s side and passenger’s side. Each temperature setting is shown on the display. With the dial set at your desired temperature, the system automatically adjusts the tempera- ture of air supplied from the outlets such that the desired temperature is achieved...
Page 192 4-10 Climate control ! A/C – Air conditioner button If the windshield starts to fog when the climate control system is operated in the AUTO mode, push the air conditioner button “A/C” to defog and dehumidify. When this button is pushed, the air conditioner compressor turns on and the indicator light “A/C”...
Page 193: Temperature Sensors
When the temperature control dial is turned fully counterclockwise, the recircu- lation mode is automatically selected.) When the outside air mode is selected, a “ ” indicator light appears on the dis- play. WARNING Continued operation in the “ ” position may fog up the windows.
Page 194: Operating Tips For Heater And Air Conditioner
HFC134a. Therefore, the meth- od of adding, changing or checking the refrigerant is different from the method for CFC12 (freon). Consult your SUBARU dealer for service. Repairs needed as a result of using the wrong refrigerant are not covered under warranty.
Page 195: Air Filtration System
Under extremely dusty conditions, the filter should be replaced more frequently. Have your filter checked or replaced by your SUBARU dealer. For replacement, use only a genuine SUBARU air filter kit. Replacement schedule:...
Page 196: Audio
Antenna system ... Printed antenna... FM reception ... satellite radio reception (if equipped)... Installation of accessories... Audio set ... Type A audio set (if equipped) ... Type B audio set (if equipped) ... Power and sound controls ... Power switch and volume control ... Tone and balance control ...
Page 197: Antenna System
Audio Antenna system & Printed antenna CAUTION Do not use sharp instruments or window cleaner containing abra- sives to clean the inner surface of the window on which the antenna is printed. Doing so may damage the antenna printed on the window. Sedan Station wagon The antenna is printed on the inner...
Page 198 You may experience problems in receiving satellite radio signals in the follow- ing situations. . If you are driving northward in a coastal area You will notice that the XM satellite radio antenna is fixed to the upper right hand corner of your windshield. The signal comes from the south and may not be able to reach the antenna in some circumstances when you are driving north.
Page 199: Installation Of Accessories
Audio Installation of accessories Always consult your SUBARU dealer before installing a citizen band radio or other transmitting device in your vehicle. Such devices may cause the electronic control system to malfunction if they are incorrectly installed or if they are not...
Page 200: Audio Set
Audio set Your SUBARU may be equipped with one of the following audio sets. See the pages indicated in this section for operating details. & Type A audio set (if equipped) Audio The audio set will operate only when the ignition switch is in the “Acc”...
Page 201: Type B Audio Set (If Equipped)
Audio & Type B audio set (if equipped) The audio set will operate only when the ignition switch is in the “Acc” or “ON” position. . Power and sound controls: refer to page 5-7 . Radio operation: refer to page 5-10 .
Page 202: Power And Sound Controls
Power and sound controls & Power switch and volume control The dial is used for both power (ON/OFF) and volume control. The radio is turned ON and OFF by pushing the dial and the volume is controlled by turning the dial. The dial can also be used for tone and balance adjustment.
Page 203 Audio Control mode (Range of levels) Turn counterclockwise Bass control (−6 to +6) For less bass sound Midrange control (−6 to +6) For less midrange sound Treble control (−6 to +6) For less treble sound Volume control (0 to 40) For less volume AUX volume control* (0 to 40) For less volume...
Page 204 Control mode (Range of levels) Turn counterclockwise Fader control (R9 to F9) To decrease front speaker vo- Balance control (L9 to R9) To increase left speaker vo- lume and decrease right speaker volume Volume control (0 to 40) For less volume AUX volume control* (0 to 40) For less volume * Only when an AUX audio product is connected.
Page 205: Fm/Am Radio Operation
5-10 Audio FM/AM radio operation & FM/AM selection Push the “FM AM” button when the radio is off to turn on the radio. Push the “FM AM” button when the radio is on to select FM1, FM2 or AM reception. Each brief press of the “FM AM”...
Page 206: Station Preset
! Scan tuning (SCAN) If you press the “ ” or “ ” side of the SEEK/SCAN button for 0.5 second or longer, the radio will switch to scan mode. In this mode, the radio scans through the radio band until a station is found. The radio will stop at the station for 5 seconds while displaying the frequency, after which scanning will continue until the entire band...
Page 207: Satellite Radio Operation (If Equipped)
5-12 Audio Satellite radio operation (if equipped) To receive satellite radio, it is necessary to install the SUBARU genuine satellite receiver (dealer option) and to enter into a contract. For details, please contact your SUBARU dealer. & XM satellite radio is a continental U.S.
Page 208: Channel And Category Selection
& Channel and category selec- tion ! Channel selection Press “ ” of the TUNE TRACK button to select the next channel and press “ ” of the button to select the previous channel. Keep pressing “ ” of the button to change to the next channel continuously and keep pressing “...
Page 209: Channel Preset
5-14 Audio & Channel preset ! How to preset channels 1. Press the “SAT” button to select SAT1, SAT2 and SAT3 reception. 2. Press the SEEK/SCAN button or the TUNE TRACK button to select the chan- nel. 3. Press one of the preset buttons for more than 1.5 seconds to store the channel.
Page 210: Cd Player Operation
CD player operation NOTE . Make sure to always insert a disc with the label side up. If a disc is inserted with the label side down, the player displays “CHECK DISC”. Refer to “When the following messages are displayed” in this section. .
Page 211 5-16 Audio ! Inserting a disc in a desired posi- tion 1. Briefly press the “LOAD” button. If the magazine in the player has an idle position where you can insert a disc, the disc number indicator associated with the idle position will blink.
Page 212: How To Play Back A Cd
start playback of the discs, beginning with the one inserted first. If you fail to insert any disc during each 15 seconds interval, the full disc loading mode will be canceled, and the player will start playback of the disc inserted first. &...
Page 213: Fast-Forwarding And Fast-Reversing
5-18 Audio ! Backward direction Briefly press the “ ” side of the TUNE/ TRACK button to skip to the beginning of the current track/file (track). Each time the button is pressed, the indicated track/file (track) number will decrease. NOTE In an MP3 or WMA folder, skipping past the first track/file (track) will take you to the last track/file (track) in the folder.
Page 214: Repeating
& Repeating ! To repeat the currently playing track/file (track) To repeat a track/file (track), briefly press the “RPT” button while the track/file (track) is playing. The display will show “RPT”, and the track/file (track) will be repeated. To cancel the track/file (track) repeat-play mode, briefly press the “RPT”...
Page 215: Random Playback
5-20 Audio If you accidentally press the button and cancel the disc/folder repeat-play mode, press it again to reselect the disc/folder repeat-play mode. . For MP3 and WMA discs, they can play back repeatedly only for the currently playing file folder. They can- not play back the whole disc.
Page 216: Scan
If you accidentally press the button and cancel the random mode, press it again to reselect the random mode. . Random playback will be cancelled if you perform any of the following steps: . Press the “RPT” button . Press the “ ”...
Page 217: Display Selection
5-22 Audio & Display selection If you briefly press the “TEXT” button during playback of an MP3/WMA file, the indication will change to the next one in the following sequence. ! Page (track/folder title) scroll If, having pressed the “TEXT” button to select FOLDER NAME or TRACK NAME display, you press the “TEXT”...
Page 218: How To Eject A Cd From The Player (Type A)
& How to eject a CD from the player (type A) When a disc is being played back or when a disc is in the player, press the eject button “ ”. The disc will be ejected. NOTE . Avoid driving the vehicle with a CD sticking out, because vibration might make it fall out.
Page 219: When The Following Messages Are Displayed
CD player, determine the cause based on the follow- ing information. If you cannot clear those ” messages, please contact your SUBARU dealer. ! When “PUSH EJECT” is displayed Press the eject button to unload the disc.
Page 220: Aux Unit Operation
AUX unit operation & AUX jack By connecting a commercial audio pro- duct to the vehicle, such as a portable audio player, you can hear its sound via the vehicle’s speaker. Connect the portable audio player and push the “AUX” button. For the audio input jack, a stereo mini pin plug (3.5ø) can be connected.
Page 221: Audio Control Buttons (If Equipped)
5-26 Audio Audio control buttons (if equipped) These buttons are located on the spokes of the steering wheel. They allow the driver to control audio functions without taking his/her hands off the steering wheel. & MODE button This button is used to select the desired audio mode.
Page 222: Precautions To Observe When Handling A Compact Disc
! MUTE button Press this button if you wish to immedi- ately cut the volume to zero. The audio display will show “MUTE”. If you press the button again, the original sound volume will return and “MUTE” goes off. Precautions to observe when handling a compact disc Use only compact discs (CDs, CD-Rs and CD-RWs) that have the mark shown in the...
Page 223 5-28 Audio . You cannot use a DualDisc in the CD player. If you insert a DualDisc into the player, the disc may not come out again, possibly causing the player to malfunction. . In cold and/or rainy weather, dew can form inside the CD player, preventing normal operation.
Page 224 Interior light ... Dome light ... Cargo area light (Station wagon)... Map light ... Sun visors ... Sun visor extension plate ... Vanity mirror with light ... Storage compartment ... Glove box ... Center console box ... Center panel compartment (if equipped)... Overhead console (if equipped) ...
Page 225: Interior Equipment
The setting of the period for which the light stays on can be changed as follows. . Vehicles with genuine SUBARU na- vigation system: The setting can be changed using the monitor. For details, please refer to the Owner’s Manual supplement for the moni-...
Page 226: Map Light
Interior equipment The setting of the period for which the lights stay on can be changed as follows. . Vehicles with genuine SUBARU na- vigation system: The setting can be changed using the monitor. For details, please refer to the Owner’s Manual supplement for the moni-...
Page 227: Sun Visors
Interior equipment Sun visors To block out glare, swing down the visors. To use the sun visor at a side window, swing it down and move it sideways. & Sun visor extension plate With the sun visor positioned over the side window, you can use the sun visor extension plate to prevent glare through the gap between the sun visor and center...
Page 228: Vanity Mirror With Light
& Vanity mirror with light CAUTION Keep the vanity mirror cover closed while the car is being driven to avoid dazzle. To use the vanity mirror, swing down the sun visor and open the vanity mirror cover. The light beside the vanity mirror illumi- nates when the ignition switch is either in the “Acc”...
Page 229: Center Console Box
Interior equipment & Center console box Center console box (front) If you remove the divider plate from the dual cup holders, you can use the center console box as a storage space. To use as storage space: Slide the sliding lid (near the parking brake lever) toward the rear.
Page 230: Center Panel Compartment (If Equipped)
Center console box (rear) Pull up the lock release knob at the bottom of the front edge of the lid. & Center panel compartment (if equipped) CAUTION When your vehicle is parked in the sun or a warm day, the inside of the center panel heats up.
Page 231: Pocket
Interior equipment & Pocket CAUTION Do not use the pocket as an ashtray or leave a lighted cigarette in the pocket. This could cause a fire. To use the pocket, push lightly on the lid below the climate controls. Cup holder CAUTION .
Page 232: Rear Passenger's Cup Holder
& Rear passenger’s cup holder The rear passenger’s cup holder is located on the lower side of the back of the center console. To use the cup holder, open the lid by pulling its upper edge. Accessory power outlets Power outlet next to the front pocket Power outlet in the center console Interior equipment Power outlet in the cargo area (if equipped)
Page 233: Use With A Cigarette Lighter (Canada Only - If Equipped)
A cigarette lighter plug is available from your SUBARU dealer. The cigarette lighter operates only when the ignition switch is in the “ON” or “Acc”...
Page 234: Ashtray (Canada Only - If Equipped)
This could cause a fire. A portable front ashtray is available from your SUBARU dealer. It fits into one of the cup holders built into the center console. When using the ashtray, open the ashtray lid. Fully close the lid after using it to help reduce residual smoke.
Page 235: Coat Hook
6-12 Interior equipment NOTE Particles of ash and tobacco will accu- mulate around the hinges of the ash- tray’s inner lid. Clean them off using a toothbrush or another narrow-ended implement. Coat hook & Rear passenger area WARNING Do not hang coat hangers or other hard or pointed objects on the coat hooks.
Page 236: Shopping Bag Hook
Shopping bag hook CAUTION Do not hang items on the shopping bag hook that weigh 11 lbs (5 kg) or more. & For Sedan models A shopping bag hook is attached to each inner side wall of the trunk near the trunk lid opening.
Page 237: Cargo Area Cover (If Equipped)
6-14 Interior equipment CAUTION Make sure the driver’s floor mat is placed back in its proper location and correctly secured on its retain- ing pin. Also, do not use more than one floor mat. If the floor mat slips forward and interferes with the movement of the pedals during driving, it could cause an accident.
Page 238: To Remove The Rear Gate Board
& To remove the rear gate board 1. Remove the top of the rear gate board from the groove in the rear gate panel. 2. Hold both sides of the bottom edge of the rear gate board, rotate the rear gate board toward you, and pull it out down- ward.
Page 239: To Install The Cover Housing
6-16 Interior equipment 4. Stow the cover housing and rear gate board in the cargo area end. & To install the cover housing To install the cover housing, insert both ends of the cover housing into the retainers. & To install the rear gate board Insert (tipped at an angle) the hooks on the rear gate board into the holes in the rear gate panel.
Page 240: Stowage Boxes (Station Wagon)
Rotate the rear gate board toward you until its top touches the rear gate panel. Fit the top of the rear gate board into the groove in the rear gate panel. Stowage boxes (Station wa- gon) A stowage box is located on each side of the cargo area.
Page 241: Under-Floor Storage Compartment
6-18 Interior equipment storing recesses. Under-floor storage compart- ment The subfloor storage compartment is located under the floor of the trunk or cargo area and can be used to store small items. To open the lid, pull the tab or handle up.
Page 242: Homelink® Wireless Control System (If Equipped)
HomeLink® Wireless Control System (if equipped) HomeLink® buttons Indicator light Hand-held transmitter* * Not part of your vehicle’s remote keyless entry system but of a HomeLink®-compatible device. The HomeLink® Wireless Control System, located on the driver’s sun visor, is a handy way to operate, from inside of your vehicle, up to three remote-controlled indoor and outdoor devices, such as...
Page 243: Garage Door Opener Programming In The U.s.a
6-20 Interior equipment NOTE . After programming your HomeLink® Wireless Control System for the de- sired devices, retain the hand-held transmitters for further programming or device testing in the event of a problem. . It is recommended that you insert a new battery in the hand-held transmit- ter of a device to ensure correct programming.
Page 244: Programming Rolling-Code-Protected Garage Door Openers In The U.s.a
your garage door opener may be pro- tected by a rolling code feature. In this case you need to perform the additional steps for “Programming rolling-code-pro- tected garage door openers in the U.S.A.” described in the following. NOTE Rolling-code-protected garage door openers are manufactured after 1996.
Page 245: Programming For Entrance Gates And Garage Door Openers In Canada
6-22 Interior equipment trol System and your garage door opener should activate when the HomeLink® button is pressed. & Programming for entrance gates and garage door open- ers in Canada 1. Unplug the motor of the entrance gate or garage door opener from the outlet. 2.
Page 246: Erasing Homelink® Button Memory
3. Press and hold the hand-held trans- mitter button. The HomeLink® indicator light will flash, first slowly and then rapidly. 4. When the indicator light begins to flash rapidly, release both buttons. The programming for the previous device is now erased and the new device can be operated by pushing the HomeLink®...
Page 247: Starting And Operating
Fuel ... Fuel requirements ... Fuel filler lid and cap... State emission testing (U.S. only)... Preparing to drive ... Starting the engine... Manual transmission vehicle... Automatic transmission vehicle ... Stopping the engine... Remote engine start system (dealer option) ... Starting your vehicle ... Remote start safety features ...
Page 248 Starting and operating ABS warning light ... Electronic Brake Force Distribution (EBD) system ... 7-37 Steps to take if EBD system fails ... Vehicle Dynamics Control system (if equipped) ... 7-38 Vehicle Dynamics Control system monitor ... Vehicle Dynamics Control OFF switch... Tire pressure monitoring system (TPMS) (if equipped) ...
Page 249: Fuel
Fuel CAUTION Use of a fuel which is low in quality or use of an inappropriate fuel additive may cause engine damage. & Fuel requirements ! 2.5 L non-turbo models The 2.5 L non-turbo engine is designed to operate using unleaded gasoline with an octane rating of 87 AKI or higher.
Page 250 CHECK ENGINE warning light/mal- function indicator lamp may turn on. If this happens, return to your authorized SUBARU Dealer for service. If it is determined that the condition is caused by the type of fuel used, repairs may not be covered by your warranty.
Page 251: Fuel Filler Lid And Cap
. Fuel system damage or driveability problems which result from the use of improper fuel are not covered under the SUBARU Limited Warranty. & Fuel filler lid and cap ! Refueling Only one person should be involved in refueling. Do not allow others to approach the area of the vehicle near the fuel filler pipe while refueling is in progress.
Page 252 Starting and operating WARNING . Gasoline vapor is highly flam- mable. Before refueling, always first stop the engine and close all vehicle doors and windows. Make sure that there are no lighted cigarettes, open flames or electrical sparks in the adja- cent area.
Page 253: State Emission Testing (U.s. Only)
Paint damage caused by spilled fuel is not covered under the SUBARU Limited Warranty. . Always use a genuine SUBARU fuel filler cap. If you use the wrong cap, it may not fit, and your fuel tank and emission con- trol system may be damaged.
Page 254: Preparing To Drive
Starting and operating not damage an AWD SUBARU vehicle. Under no circumstances should the rear wheels be jacked off the ground, nor should the driveshaft be disconnected for state emission testing. The EPA has issued regulations for inspecting the On-Board Diagnostic (OBD) system as part of the state emis- sions inspection.
Page 255: Starting The Engine
“LOCK” position. After waiting for 10 seconds or longer, turn the ignition switch to the “START” position without depressing the accelerator pedal. (4) If the engine still refuses to start, contact your nearest SUBARU dealer for assistance. – CONTINUED –...
Page 256: Automatic Transmission Vehicle
“START” position without depressing the accelerator pedal. (4) If the engine still refuses to start, contact your nearest SUBARU dealer for assistance. 6. Confirm that all warning and indicator lights have gone out after the engine has started.
Page 257: Stopping The Engine
speed may not become too high even if the accelerator pedal is depressed hard. Stopping the engine WARNING Do not stop the engine when the vehicle is moving. This will cause loss of power to the power steering and the brake booster, making steer- ing and braking more difficult.
Page 258: Starting Your Vehicle
7-12 Starting and operating & Starting your vehicle The remote control start system is acti- vated by pressing the “ ” button twice within 3 seconds on your remote control transmitter. The system will check certain pre-conditions before starting, and if all safety parameters are correct, the engine will start within 5 seconds.
Page 259: Pre-Heating Or Pre-Cooling The Interior Of The Vehicle
transmitter within a few seconds immedi- ately following remote engine start shut- down. & Pre-heating or pre-cooling the interior of the vehicle Before exiting the vehicle, set the tem- perature controls to the desired setting and operation. After the system starts the vehicle, the heater or air-conditioning will activate and heat or cool the interior to your setting.
Page 260: System Maintenance
7-14 Starting and operating feature ON or OFF each time. 7. To exit the remote transmitter and feature programming mode, turn the igni- tion switch to the “LOCK” position, remove the key from the ignition switch and test operation of the remote transmitter(s) and horn confirmation feature.
Page 261: Shifting Speeds
on the old batteries before removing them to ensure that the new batteries are inserted properly (battery “+” should be pointed away from the transmitter circuit board on both batteries). 3. Carefully snap the case halves back together, then test the remote control. NOTE This device complies with Part 15 of the FCC Rules and with RSS-210 of...
Page 262: Driving Tips
7-16 Starting and operating Shift up mph (km/h) 1st to 2nd 15 (24) 2nd to 3rd 25 (40) 3rd to 4th 35 (56) 4th to 5th 45 (73) ! Maximum allowable speeds WARNING When shifting down a gear, ensure that the vehicle is not travelling at a speed exceeding the Maximum Al- lowable Speed for the gear which is about to be selected.
Page 263: Selecting Reverse Gear
Manual transmission – 6 speeds (2.5GT spec.B) WARNING Do not drive the vehicle with the clutch disengaged (i.e., when the clutch pedal is depressed) or with the shift lever in the neutral position. Engine braking has no effect in either of these conditions and the risk of an accident is consequently increased.
Page 264: Driving Tips
7-18 Starting and operating can result in engine damage. In addition, sudden application of engine brakes when the vehicle is travelling on a slippery surface can lead to wheel locking; as a conse- quence, control of the vehicle may be lost and the risk of an accident increased.
Page 265: Selector Lever
forward driving positions into the “R” position or vice versa until the vehicle has completely stopped. Such shifting may cause damage to the transmis- sion. . When parking the vehicle, first securely apply the parking brake and then place the selector lever in the “P”...
Page 266: Selector Lever Reverse Inhibiting Function
7-20 Starting and operating NOTE If the selector lever is in the “N” position when you stop the engine for parking, you may not subsequently be able to move it to the “R” and “P” positions. If this happens, turn the ignition switch to the “ON”...
Page 267: Selection Of Manual Mode
“P” position. If the selector lever reverse inhibiting function fails, have the vehicle inspected by the nearest SUBARU dealer. & Selection of manual mode With the vehicle either moving or station- ary, move the selector lever from the “D”...
Page 268: Maximum Speeds
7-22 Starting and operating selector lever. Using the selector lever Shift to the next-higher gear by briefly pushing the selector lever toward the “+” end of the manual gate. Shift to the next-lower gear by briefly pulling the selector lever toward the “−” end of the manual gate.
Page 269: Driving Tips
mph (km/h) Position 2.5 L non-turbo models 30 (48) 63 (101) 99 (160) Never exceed posted speed limits. NOTE In order to prevent over-revving during deceleration of the vehicle, the trans- mission will remain in the current gear if the speed of the vehicle is in excess of the Maximum Allowable Speed for the gear to which the selector lever has been moved.
Page 270: Shift Lock Release
“P” to the “N” position. 6. Remove the screwdriver from the hole. Depress the brake pedal and start the engine. Take your vehicle to the nearest SUBARU dealer immediately to have the system repaired. Automatic transmission – 5- speed...
Page 271: Selector Lever
forward driving positions into the “R” position or vice versa until the vehicle has completely stopped. Such shifting may cause damage to the transmis- sion. . When parking the vehicle, first securely apply the parking brake and then place the selector lever in the “P”...
Page 272: Selector Lever Reverse Inhibiting Function
7-26 Starting and operating transmission is neutral; the vehicle will roll freely, even on the slightest incline unless the parking brake or foot brake is on. Avoid coasting with the transmission neutral. During coasting, there is no engine brak- ing effect. NOTE (3.0 L models only) To protect the engine while the “N”...
Page 273: Selection Of Manual Mode
“P” position. If the selector lever reverse inhibiting function fails, have the vehicle inspected by the nearest SUBARU dealer. 7-27 Starting and operating & Selection of manual mode With the vehicle either moving or station- ary, move the selector lever from the “D”...
Page 274 7-28 Starting and operating Upshift indicator Downshift indicator Gear position indicator When the manual mode is selected, the gear position indicator and upshift indica- tor and/or downshift indicator in the tachometer illuminate. The gear position indicator shows the currently selected gear in the 1st-to-5th-gear range.
Page 275: Maximum Speeds
Also, if you subsequently ease off the accelerator pedal and then accelerate again, the transmission will automatically switch back from manual mode to normal mode. CAUTION Do not place or hang anything on the paddle shift levers. Doing so may result in accidential gear shift- ing.
Page 276: Shift Lock Release
“P” to the “N” position. 6. Remove the screwdriver from the hole. Depress the brake pedal and start the engine. Take your vehicle to the nearest SUBARU dealer immediately to have the system repaired.
Page 277: Si-Drive (Turbo And 3.0 L Models)
SI-DRIVE (turbo and 3.0 L models) SI-DRIVE (Subaru Intelligent Drive) works to maximize engine performance, control and efficiency. This system consists of three modes: Intelligent (I), Sport (S), and Sport Sharp (S#). By adjusting the SI-DRIVE selector, the character of the power unit changes.
Page 278: Sport (S) Mode
7-32 Starting and operating & Sport (S) mode For all-around performance driving The Sport (S) mode provides the engine power desired by those who want to make the driving experience their own personal adventure. The linear acceleration characteristic of this versatile mode is ideal for normal driving use.
Page 279: Si-Drive Sport Sharp (S#) Switch
mode. . The next time you turn on the engine, after you turned off the engine in the Sport (S) mode or Intelligent (I) mode, the SI-DRIVE mode will stay in the same mode as when the engine was turned off. .
Page 280: Power Steering
7-34 Starting and operating Power steering CAUTION Do not hold the steering wheel at the fully locked position left or right for more than 5 seconds. This may damage the power steering pump. The power steering system operates only when the engine is running. If you lose power steering assist because the engine stops or the system fails to function, you can steer but it will take...
Page 281: Disc Brake Pad Wear Warning Indicators
If a squeaking or scraping noise is heard from the disc brakes while braking, im- mediately have your vehicle inspected by the nearest SUBARU dealer. ABS (Anti-lock Brake Sys- tem) WARNING Always use the utmost care in driving –...
Page 282: Abs Warning Light
. The warning light illuminates dur- ing driving. If these occur, have the ABS system repaired at the first available oppor- tunity by your SUBARU dealer. NOTE If the warning light behavior is as described in the following, the ABS system may be considered normal.
Page 283: Electronic Brake Force Distribution (Ebd) System
3. Release the parking brake. If both warning lights go out, the EBD system may be faulty. Drive carefully to the nearest SUBARU dealer and have the system inspected. 4. If both warning lights illuminate again and stay illuminated after the engine has...
Page 284: Vehicle Dynamics Control System (If Equipped)
7-38 Starting and operating “MIN” mark, the EBD system may be faulty. Drive carefully to the nearest SUBARU dealer and have the system inspected. 6. If the brake fluid level is below the “MIN” mark, DO NOT drive the vehicle.
Page 285 spare tire, the effectiveness of the Vehicle Dynamics Control system is reduced and this should be taken into account when driving the vehicle in such a condition. In the event of wheelspin and/or skidding on a slippery road surface and/or during cornering and/or an evasive maneuver, the Vehicle Dynamics Control system adjusts the engine’s output and the...
Page 286: Vehicle Dynamics Control System Monitor
The following two situations could indicate a malfunction of the Vehicle Dynamics Control system; if either should occur, have an authorized SUBARU dealer carry out an inspection of that system at the first available opportunity. . The indicator light does not turn on when the ignition switch is turned to the ON position.
Page 287 SUBARU dealer carry out an inspection of those systems at the first available oppor- tunity. NOTE...
Page 288: Vehicle Dynamics Control Off Switch
7-42 Starting and operating available opportunity. . The indicator light does not turn on when the ignition switch is turned to the ON position. . The indicator light fails to turn off after the engine is started, even when several minutes have passed to allow the engine to heat up sufficiently.
Page 289: Tire Pressure Monitoring System (Tpms) (If Equipped)
Tire pressure monitoring system (TPMS) (if equipped) Vehicle with SI-DRIVE Vehicle without SI-DRIVE The tire pressure monitoring system pro- vides the driver with a warning message by sending a signal from a sensor that is installed in each wheel when tire pressure is severely low.
Page 290: Parking Your Vehicle
7-44 Starting and operating four road wheels. Contact your SUBARU dealer as soon as possible for tire and sensor replacement and/ or system resetting. Do not inject any tire liquid or aerosol tire sealant into the tires, as this may cause a malfunction of the tire pressure sensors.
Page 291: Parking Brake
& Parking brake CAUTION Never drive while the parking brake is set because this will cause un- necessary wear on the brake lin- ings. Before starting to drive, always make sure that the parking brake has been fully released. To set the parking brake, press the brake pedal firmly and hold it down while fully pulling up the parking brake lever.
Page 292: To Set Cruise Control
7-46 Starting and operating Cruise control Cruise control enables you to maintain a constant vehicle speed without holding your foot on the accelerator pedal and it is operative when the vehicle speed is 25 mph (40 km/h) or more. Make sure the main switch is turned “OFF”...
Page 293: To Temporarily Cancel The Cruise Control
release it. Then release the accelerator pedal. Vehicle with SI-DRIVE Vehicle without SI-DRIVE At this time, the “ ” indicator light is illuminated in the combination meter. The vehicle will maintain the desired speed. Vehicle speed can be temporarily in- creased while driving with the cruise control activated.
Page 294: To Turn Off The Cruise Control
7-48 Starting and operating & To turn off the cruise control There are two ways to turn off the cruise control: . Push the “CRUISE” main switch button again. . Turn the ignition switch to the “Acc” or “LOCK” position (but only when the vehicle is completely stopped).
Page 295: Cruise Control Indicator Light
“Acc” or “LOCK” position, and then turn it again to the “ON” position. . If this indicator light and the CHECK ENGINE warning light/malfunction in- dicator lamp flash simultaneously dur- ing driving, have the vehicle checked by your nearest SUBARU dealer. – CONTINUED –...
Page 296: Cruise Control Set Indicator Light
7-50 Starting and operating & Cruise control set indicator light Vehicle with SI-DRIVE Vehicle without SI-DRIVE The cruise control set indicator light illuminates when the ignition switch is turned to the “ON” position and goes out after approximately 3 seconds. The light illuminates when vehicle speed has been set.
Page 297: Driving Tips
New vehicle break-in driving – the first 1,000 miles (1,600 km) ... Fuel economy hints ... Engine exhaust gas (carbon monoxide)... Catalytic converter ... Periodic inspections ... Driving in foreign countries ... Driving tips for AWD vehicles ... Off road driving ... All AWD models except OUTBACK ...
Page 298: New Vehicle Break-In Driving - The First 1,000 Miles (1,600 Km)
Driving tips New vehicle break-in driving – the first 1,000 miles (1,600 The performance and long life of your vehicle are dependent on how you handle and care for your vehicle while it is new. Follow these instructions during the first 1,000 miles (1,600 km): .
Page 299: Engine Exhaust Gas (Carbon Monoxide)
Engine exhaust gas (carbon monoxide) WARNING . Never inhale engine exhaust gas. Engine exhaust gas contains carbon monoxide, a colorless and odorless gas which is dan- gerous, or even lethal, if inhaled. . Always properly maintain the en- gine exhaust system to prevent engine exhaust gas from enter- ing the vehicle.
Page 300: Periodic Inspections
(misfiring, back- firing or incomplete combustion), have your vehicle checked and repaired by an authorized SUBARU dealer. . Do not apply undercoating or rust prevention treatment to the heat shield of catalytic converter and the exhaust sys- tem.
Page 301: Driving In Foreign Countries
By shifting power between the front and rear wheels, SUBARU AWD can also provide added traction during accelera- tion, and added engine braking force during deceleration.
Page 302: Off Road Driving
If you do take your SUBARU off road, you should review the common sense precautions in the next section (applicable to the OUTBACK) for general guidance.
Page 303 “Warranty and Mainte- nance Booklet”. Remember that damage done to your SUBARU while operating it off-road and – CONTINUED –...
Page 304: Winter Driving
Do not use engine antifreeze or other substitutes because they may damage the paint of the vehicle. SUBARU Windshield Washer Fluid con- tains 58.5% methyl alcohol and 41.5% surfactant, by volume. Its freezing tem- perature varies according to how much it is diluted, as indicated in the following table.
Page 305: Driving On Snowy And Icy Roads
If your SUBARU is not going to be used for an extended period, it is best to have the fuel tank filled to capacity.
Page 306: Corrosion Protection
8-10 Driving tips CAUTION Avoid prolonged continuous driving in snowstorms. Snow will enter the engine’s intake system and may hinder the air flow, which could result in engine shutdown or even breakdown. To prevent skidding and slipping, avoid sudden braking, abrupt acceleration, high- speed driving, and sharp turning when driving on snowy or icy roads.
Page 307: Snow Tires
& Snow tires ! All models except OUTBACK or 2.5GT spec.B WARNING . When replacing original tires with winter (snow) tires, make sure you use only the same size, construction and load range as the original tires listed on the tire placard.
Page 308 8-12 Driving tips . Do not use a combination of radial, belted bias or bias tires since it may cause dangerous handling characteristics and lead to an accident. Your vehicle is equipped with “all season tires” which are designed to provide an adequate measure of traction, handling and braking performance in year-round driving.
Page 309: Tire Chains
never mix radial, belted bias or bias tires since this may result in dangerous hand- ling characteristics. When you choose a tire, make sure that there is enough clearance between the tire and vehicle body. Remember to drive with care at all times regardless of the type of tires on your vehicle.
Page 310: Vehicle Capacity Weight
8-14 Driving tips possible. . When you carry something inside the vehicle, secure it whenever you can to prevent it from being thrown around inside the vehicle during sudden stops, sharp turns or in an accident. . Do not pile heavy loads on the roof.
Page 311: Gvwr And Gawr (Gross Vehicle Weight Rating And Gross Axle Weight Rating)
side door pillar. It includes the total weight of the driver and all passengers and their belongings, any optional equipment such as a trailer hitch, roof rack or bike carrier, etc., and the tongue load of a trailer. & GVWR and GAWR (Gross Vehicle Weight Rating and Gross Axle Weight Rating) Certification label...
Page 312 8-16 Driving tips ment and cargo does not exceed the maximum load limit. Over- loading may cause damage to the vehicle and create a safety hazard. The roof rail is not designed to carry cargo by itself. Cargo can be carried after securing the roof crossbar kit to the roof rail and installing the appropriate carrying attachment.
Page 313 2. Carefully raise the crossbar from roof rails. ! To install the front crossbar Front crossbar: Front crossbar has 100 LBS Load Label on left-hand side. T-25 torx® head screw 1. Make sure that the T-25 torx® head screw on the back of each crossbar end support is tightened correctly.
Page 314 8-18 Driving tips Lower clamp T-30 torx® head screw 5. Tighten the lower clamps onto the crossbar. Using a torque wrench, loosely tighten the T-30 torx® head screws. NOTE It may be necessary to squeeze the lower clamp and the end support together to compress the pads and gain a better alignment of the pieces while trying to start the screw.
Page 315: Trailer Hitch (If Equipped)
NOTE Before each use of the roof crossbar, make sure the four T-30 crossbar clamp screws have been checked, and retightened if necessary to 35 lbf·in (4.0 N·m, 0.41 kgf·m), as outlined in Step #5 above. Trailer hitch (if equipped) WARNING .
Page 316: Connecting A Trailer
8-20 Driving tips & Connecting a trailer 1. Remove the receiver cover from the hitch receiver tube. Then insert the ball mount into the hitch receiver tube. 2. Insert the hitch pin into the hole on the hitch receiver tube so that the pin passes through the ball mount.
Page 317: When You Do Not Tow A Trailer
Seek the advice of your SUBARU dealer to assist you in purchasing a hitch and other necessary towing equipment appropriate for your vehicle. In addition, be sure to follow the...
Page 318: Maximum Load Limits
8-22 Driving tips (Refer to “Maintenance schedule under severe driving conditions” in the “Warranty and Maintenance Booklet”.) Under no circumstances should a trailer be towed with a new vehicle or a vehicle with any new powertrain component (en- gine, transmission, differential, wheel bearings, etc.) for the first 1,000 miles (1,600 km) of driving.
Page 319 3.0 L models Conditions When towing a trailer without brakes. When towing a trailer with brakes. When towing a trailer on a long uphill grade continuously for over 5 miles (8 km) with an outside temperature of 1048F (408C) or above. All models other than 3.0 L models Model Conditions...
Page 320 8-24 Driving tips Certification label ! Gross Axle Weight (GAW) and Gross Axle Weight Rating (GAWR) Gross Axle Weight The total weight applied to each axle (GAW) must never exceed the Gross Axle Weight Rating (GAWR). The front and rear GAWs can be adjusted by relocating passengers and luggage inside the vehi- cle.
Page 321: Trailer Hitches
NOTE For vehicles with trailer brakes, the trailer tongue load exceeds 200 lbs (90 kg) when calculated at 8% of the maximum total trailer weight. Even in this case, the maximum value is 200 lbs (90 kg). Jack Bathroom scale The tongue load can be weighed with a bathroom scale as shown in the following illustration.
Page 322: Connecting A Trailer
8-26 Driving tips trailer. ! OUTBACK wagon The use of a genuine SUBARU trailer hitch is recommended. A genuine SUBARU hitch is available from your SUBARU dealer. If use of a non-genuine hitch is unavoid- able, be sure the hitch is suited to your vehicle and trailer.
Page 323: Trailer Towing Tips
To ensure the trailer lights are connected properly, please consult your SUBARU dealer. Check for proper operation of the turn signals, the brake lights and parking lights each time you hitch up.
Page 324 . If the ABS warning light illuminates while the vehicle is in motion, stop towing the trailer and have repairs performed immediately by the nearest SUBARU dealer.
Page 325 ! Driving on grades . Before going down a steep hill, slow down and shift into lower gear (if neces- sary, use 1st gear) in order to utilize the engine braking effect and prevent over- heating of your vehicle’s brakes. Do not make sudden downshifts.
Page 326 If you park your vehicle in an emergency... Temporary spare tire... Precautions for AWD vehicles with automatic transmission ... Flat tires... Changing a flat tire... Tire pressure monitoring system (TPMS) (if equipped)... Jump starting ... 9-10 How to jump start... Engine overheating ...
Page 327: In Case Of Emergency
This indicates the tire pressure monitoring system (TPMS) is un- able to monitor all four road wheels. Contact your SUBARU dealer as soon as possible for tire and sensor replacement and/ or system resetting.
Page 328: Precautions For Awd Vehicles With Automatic Transmission
CAUTION Never use any temporary spare tire other than the original. Using other sizes may result in severe mechan- ical damage to the drive train of your vehicle. The temporary spare tire is smaller and lighter than a conventional tire and is designed for emergency use only.
Page 329: Flat Tires
In case of emergency 3. Put a spare fuse inside the FWD socket located in the fuse panel and confirm that the “ ” warning light on the combination meter illuminates. The All-Wheel-Drive capability of the vehicle has now been deactivated. NOTE After reinstalling the conventional tire, remove the spare fuse from the FWD...
Page 330 Sedan Jack handle Spare tire Jack and tool bucket Station wagon Jack handle Jack and tool bucket Spare tire 5. Take out the spare tire, jack, and jack handle. The spare tire and jack are stored under the floor of the trunk or cargo area. To remove the spare tire and jack, proceed as follows: In case of emergency...
Page 331 In case of emergency 4. Take out the jack and tool bucket. Wheel nut wrench Jack 5. Take the wheel nut wrench and jack out of the tool bucket. 6. Turn the attaching bolt counterclock- wise, then take the spare tire out. Station wagon: 1.
Page 332 4. Take out the jack and tool bucket. Wheel nut wrench Jack 5. Take the wheel nut wrench and jack out of the tool bucket. 6. Turn the attaching bolt counterclock- wise, then take spare tire out. If the spare tire provided in your vehicle is a temporary spare tire, carefully read the section “Temporary spare tire”...
Page 333 In case of emergency Turn the jackscrew by hand until the jack head engages firmly into the jack-up point. 9. Insert the jack handle into the jack- screw, and turn the handle until the tire clears the ground. Do not raise the vehicle higher than necessary.
Page 334: Tire Pressure Monitoring System (Tpms) (If Equipped)
approximately 88 to 110 lbs (40 to 50 kg) at the top of the wheel nut wrench. Never use your foot on the wheel nut wrench or a pipe extension on the wrench because you may exceed the specified torque. Have the wheel nut torque checked at the nearest automotive service facility.
Page 335: Jump Starting
This indicates the TPMS is unable to monitor all four road wheels. Contact your SUBARU dealer as soon as possible for tire and sensor replacement and/ or system resetting. Do not inject any tire liquid or...
Page 336: How To Jump Start
eye protectors, and remove metal objects such as rings, bands or other metal jewelry. . Be sure the jumper cables and clamps on them do not have loose or missing insulation. . Do not jump start unless cables in suitable condition are avail- able.
Page 337 9-12 In case of emergency Connect one jumper cable to the positive (+) terminal on the discharged battery. Connect the other end of the jumper cable to the positive (+) terminal of the booster battery. Connect one end of the other cable to the negative (−) terminal of the booster battery.
Page 338: Engine Overheating
This will cause the vehicle to spin away due to the operation or dete- rioration of the center differential. If towing is necessary, it is best done by your SUBARU dealer or a commercial towing service. Observe the following procedures for safety. – CONTINUED –...
Page 339: Towing And Tie-Down Hooks
9-14 In case of emergency & Towing and tie-down hooks The towing hooks should be used only in an emergency (e.g., to free a stuck vehicle from mud, sand or snow). CAUTION . Use only the specified towing hooks and tie-down hooks. Never use suspension parts or other parts of the body for towing or tie-down purposes.
Page 340 2. Wrap a flat-head screwdriver with cloth or vinyl. Then, insert the screwdriver into the gap between the front fog light cover and the bumper, and pry out the cover. 3. Pull the entire front fog light cover toward you. 4.
Page 341: Using A Flat-Bed Truck
9-16 In case of emergency Rear towing hook: The rear towing hook is located below the center of the rear bumper. CAUTION Never use the rear towing hook to tie the vehicle down. Front tie-down hooks: The front tie-down hooks are located between each of the front tires and the front bumper.
Page 342: Towing With All Wheels On The Ground
vehicles. 2. Pull up the parking brake lever firmly. 3. Secure the vehicle onto the carrier properly with safety chains. Each safety chain should be equally tightened and care must be taken not to pull the chains so tightly that the suspension bottoms out. &...
Page 343: Rear Gate (Station Wagon) - If The Rear Gate Cannot Be Unlocked
9-18 In case of emergency Rear gate (Station wagon) – if the rear gate cannot be un- locked In the event that you cannot unlock the rear gate by operating the power door locking switches or the remote keyless entry system, you can unlock it from inside the cargo area.
Page 344: Jack Handle
Station wagon: To take out the jack and maintenance tools, open the center lid and remove the bucket from the center of the spare tire. Then, take the jack out of the bucket. & Jack handle The jack handle is stowed on the back of the floor cover of the trunk or on the back of the center lid of the cargo area.
Page 345: Appearance Care
Exterior care ... 10-2 Washing... Waxing and polishing ... Cleaning aluminum wheels ... Corrosion protection... 10-4 Most common causes of corrosion ... To help prevent corrosion... Cleaning the interior... 10-2 Seat fabric ... 10-3 Leather seat materials... 10-3 Synthetic leather upholstery... Climate control panel, audio panel, instrument panel, console panel, switches, combination 10-4...
Page 346: Exterior Care
10-2 Appearance care Exterior care & Washing CAUTION . When washing the vehicle, the brakes may get wet. As a result, the brake stopping distance will be longer. To dry the brakes, drive the vehicle at a safe speed while lightly pressing the brake pedal to heat up the brakes.
Page 347: Waxing And Polishing
When in doubt, it is always best to contact your SUBARU dealer or an auto paint specia- list. NOTE Be careful not to block the windshield washer nozzles with wax when waxing the vehicle.
Page 348: Corrosion Protection
Contact your SUBARU dealer to perform this kind of maintenance and treatment if you need assistance. Repair chips and scratches in the paint as soon as you find them.
Page 349: Cleaning The Interior
If your SUBARU is to be parked for a long time in bright sunlight, it is recommended that the seats and headrests be covered, or the windows shaded, to prevent fading or shrinkage.
Page 350: Navigation Monitor (If Equipped)
10-6 Appearance care & Navigation monitor (if equipped) To clean the navigation monitor, wipe it with a silicone cloth or with a soft cloth. If the navigation monitor is extremely dirty, clean it with a soft cloth moistened with neutral detergent then carefully wipe off any remaining detergent.
Page 351: Maintenance And Service
Maintenance schedule ... Maintenance precautions... Before checking or servicing in the engine compartment... When you do checking or servicing in the engine compartment while the engine is running... Engine hood ... Engine compartment overview... 2.5 L non-turbo models ... 2.5 L turbo models ... 3.0 L models ...
Page 352 Maintenance and service Tire pressure monitoring system (TPMS) (if equipped)... Tire inspection ... Tire pressures and wear ... Wheel balance... Wear indicators ... Tire rotation direction mark ... Tire rotation ... Tire replacement ... Wheel replacement... Aluminum wheels... Windshield washer fluid ... Replacement of wiper blades ...
Page 353: Maintenance Schedule
Maintenance precautions When maintenance and service are re- quired, it is recommended that all work be done by an authorized SUBARU dealer. If you perform maintenance and service by yourself, you should familiarize yourself with the information provided in this section on general maintenance and service for your SUBARU.
Page 354: Before Checking Or Servicing In The Engine Compartment
NEVER use a circuit tester for these wiring. If your SRS airbag or seatbelt preten- sioner needs service, consult your nearest SUBARU dealer. & Before checking or servicing in the engine compartment WARNING . Always stop the engine and set the parking brake firmly to pre- vent the vehicle from moving.
Page 355 3. Release the secondary hood release located under the front grille by moving the lever toward the left. 4. Lift up the hood, release the hood prop from its retainer and put the end of the hood prop into the slot in the hood. To close the hood: 1.
Page 356: Fuse Box (Page
11-6 Maintenance and service Engine compartment overview & 2.5 L non-turbo models Power steering fluid reservoir (page 11-27) Manual transmission oil level gauge (MT) (page 11-21) or Differential gear oil level gauge (AT) (page 11-24) Clutch fluid reservoir (page 11-29) Automatic transmission fluid level gauge (page 11-22) Brake fluid reservoir (page 11-28)
Page 357: L Turbo Models
& 2.5 L turbo models 11-7 Maintenance and service Power steering fluid reservoir (page 11-27) Manual transmission oil level gauge (MT) (page 11-21) or Differential gear oil level gauge (AT) (page 11-24) Clutch fluid reservoir (page 11-29) Brake fluid reservoir (page 11-28) Automatic transmission fluid level gauge (page 11-22) Fuse box (page 11-47)
Page 358: L Models
11-8 Maintenance and service & 3.0 L models Power steering fluid reservoir (page 11-27) Differential gear oil level gauge (AT) (page 11-24) Automatic transmission fluid level gauge (page 11-22) Brake fluid reservoir (page 11-28) Fuse box (page 11-47) Battery (page 11-46) Windshield washer tank (page 11-41) Engine oil filler cap (page 11-9) Engine coolant reservoir (page 11-14)
Page 359: Engine Oil
1 quart per 1,200 miles or 1 liter per 2,000 kilometers, we recommend that you contact your SUBARU dealer. & Checking the oil level Check the engine oil level at each fuel stop.
Page 360: Changing The Oil And Oil Filter
11-10 Maintenance and service 3.0 L models Upper level Lower level 4. Pull out the level gauge again and check the oil level on it. If it is below the lower level, add oil to bring the level up to the upper level.
Page 361 3.0 L models 4. Drain out the engine oil by removing the drain plug while the engine is still warm. The used oil should be drained into an appropriate container and disposed of properly. WARNING Be careful not to burn yourself with hot engine oil.
Page 362: Recommended Grade And Viscosity
11-12 Maintenance and service 9. Clean the rubber seal seating area of the bottom of engine and install the oil filter by hand turning. Be careful not to twist or damage the seal. 10. Tighten the oil filter by the amount indicated in the following table after the seal makes contact with the bottom of engine.
Page 363: Recommended Grade And Viscosity Under Severe Driving Conditions
When adding oil, different brands may be used together as long as they are the same API classification and SAE viscosity as those recommended by SUBARU. SAE viscosity number and applicable temperature 5W-30 is preferred. Engine oil viscosity (thickness) affects fuel economy.
Page 364: Cooling System
, u s e o n l y SUBARU Super Coolant. If the SUBARU Super Coolant is diluted with another brand or type, the maintenance interval is shortened to that of the mixing coolant.
Page 365 Always add genuine SUBARU cooling system conditioner whenever the coolant is replaced. Change the engine coolant and add genuine SUBARU cooling system condi-...
Page 366 Fill up to here 5. Slowly pour the coolant and fill up to just below the filler neck, allowing enough room to add genuine SUBARU cooling system conditioner in the radiator. Add genuine SUBARU cooling system condi- tioner until the coolant level reaches the filler neck.
Page 367: Air Cleaner Element
CAUTION When replacing the air cleaner ele- ment, use a genuine SUBARU air cleaner element. If it is not used, there is the possibility of causing a negative effect to the engine.
Page 368: Replacing The Air Cleaner Element
Replace the air cleaner element according to the maintenance schedule in the “Warranty and Maintenance Booklet”. Un- der extremely dusty conditions, replace it more frequently. It is recommended that you always use genuine SUBARU parts. ! Non-turbo models Connector Duct Clamp 1.
Page 369 ! Turbo models 1. Use a screwdriver to undo the clips on the air intake duct, then remove the air intake duct. 2. Unplug the connector that is attached to the top of the air cleaner case. 3. Unsnap the two clamps holding the air cleaner case cover.
Page 370: Spark Plugs
It may be difficult to replace the spark plugs. It is recommended that you have the spark plugs replaced by your SUBARU dealer. The spark plugs should be replaced according to the maintenance schedule in the “Warranty and Maintenance Book- let”.
Page 371: L Models
Belt deflection should be the amount specified. If a belt is loose, cracked or worn, contact your SUBARU dealer. & 3.0 L models It is unnecessary to check the belt tension...
Page 372: Recommended Grade And Viscosity
11-22 Maintenance and service and insert it again. Upper level Lower level 3. Pull out the level gauge again and check the oil level on it. If it is below the lower level, add oil through the level gauge hole to bring the level up to the upper level.
Page 373: Recommended Fluid
& Recommended fluid Use one of the following types of auto- matic transmission fluid. – SUBARU ATF Type-HP – IDEMITSU ATF HP NOTE . For 5-speed automatic transmis- sion:...
Page 374: Front Differential Gear Oil (At Models)
11-24 Maintenance and service mance, only use the automatic trans- mission fluid that is recommended and provided by SUBARU. If the recommended automatic trans- mission fluid is unavailable, Dexron III may be temporarily used. If the Dexron III is used continuously there will be a noticeable increase in the vibration and noise from the automatic transmission.
Page 375: Recommended Grade And Viscosity
& Recommended grade and viscosity Each oil manufacturer has its own base oils and additives. Never use different brands together. Oil grade: API classification GL-5 SAE viscosity No. and applicable tempera- ture Rear differential gear oil & Checking the gear oil level Your vehicle may be equipped with a rear differential protector.
Page 376 11-26 Maintenance and service 2.5 L turbo and 3.0 L models (AT) Filler plug Drain plug Oil level 2.5 L turbo 6MT models Filler plug Drain plug Oil level Others Filler plug Drain plug Oil level Remove the plug from the filler hole and check the oil level.
Page 377: Recommended Grade And Viscosity
. If the vehicle requires frequent refilling, there may be an oil leak. If you suspect a problem, have the vehicle checked at your SUBARU dealer. & Recommended grade and viscosity Each oil manufacturer has its own base oils and additives. Never use different brands together.
Page 378: Recommended Fluid
. If the vehicle requires frequent refilling, there may be a leak. If you suspect a problem, have the vehicle checked at your SUBARU dealer. CAUTION . Never use different brands of brake fluid together. Also, avoid...
Page 379: Recommended Brake Fluid
. If the vehicle requires frequent refilling, there may be a leak. If you suspect a problem, have the vehicle checked at your SUBARU dealer. . Never use different brands of clutch fluid together. . When clutch fluid is added, be careful not to allow any dirt into the tank.
Page 380: Recommended Clutch Fluid
Brake booster If the brake booster does not operate as described in the following procedure, have it checked by your SUBARU dealer. 1. With the engine off, depress the brake pedal several times, applying the same pedal force each time. The distance the pedal travels should not vary.
Page 381: Brake Pedal
2 lbf (10 N, 1 kgf). If the free play is not within proper specification, contact your SUBARU deal- & Checking the brake pedal reserve distance More than 2.56 in (65 mm)
Page 382: Checking The Clutch Pedal Free Play
If you hear this scraping noise each time you apply the brake pedal, have the brake pads serviced by your SUBARU dealer as soon as possible. & Breaking-in of new brake pads and linings When replacing the brake pad or lining, use only genuine SUBARU parts.
Page 383: Parking Brake Stroke
(approximately 44 lbf, 196 N, 20 kgf). If the parking brake lever stroke is not within the specified range, have the brake system checked and adjusted at your SUBARU dealer. 11-33 Maintenance and service Tires and wheels &...
Page 384: Tire Pressure Monitoring System (Tpms) (If Equipped)
11-34 Maintenance and service or icy roads, we strongly recommend the use of winter (snow) tires. When installing winter tires, be sure to replace all four tires. ! Winter (snow) tires Winter tires are best suited for driving on snow-covered and icy roads. However winter tires do not perform as well as summer tires and all season tires on roads other than snow-covered and icy roads.
Page 385: Tire Inspection
In this event, go to a SUBARU dealer to have the system inspected as soon as possible. While the vehicle is driven, friction be- tween tires and the road surface causes the tires to warm up.
Page 386: Tire Pressures And Wear
Drive slowly to the nearest authorized SUBARU dealer and have the vehicle inspected. & Tire pressures and wear Maintaining the correct tire pressures helps to maximize the tires’...
Page 387 . Correct tire pressure (tread worn evenly) Roadholding is good, and steering is responsive. Rolling resistance is low, so fuel consumption is also lower. . Abnormally low tire pressure (tread worn at shoulders) Rolling resistance is high, so fuel con- sumption is also higher.
Page 388: Wheel Balance
If you suspect that the wheels are not correctly balanced, have them checked and adjusted by your SUBARU dealer. Also have them adjusted after tire repairs and after tire rotation. NOTE...
Page 389: Tire Rotation
You are advised to replace the tires with new ones that are identical to those fitted as standard equip- ment. For safe vehicle operation, SUBARU recommends replacing all four tires at the same time. – CONTINUED –...
Page 390: Wheel Replacement
. Be sure to fit tire chains on uniformly and completely around the tire, otherwise the chains may scratch the wheel. . When wheel nuts, balance weights, or the center cap is replaced, be sure to replace them with genuine SUBARU parts designed for aluminum wheels.
Page 391: Windshield Washer Fluid
In areas where water freezes in winter, use an anti-freeze type windshield washer fluid. SUBARU Windshield Washer Fluid contains 58.5% methyl alcohol and 41.5% surfactant, by volume. Its freezing tem- perature varies according to how much it is diluted, as indicated in the following table.
Page 392: Replacement Of Wiper Blades
11-42 Maintenance and service temperature, it may freeze and block the nozzles. CAUTION Adjust the washer fluid concentra- tion appropriately for the outside temperature. If the concentration is inappropriate, sprayed washer fluid may freeze on the windshield and obstruct your view, and the fluid may freeze in the reservoir tank.
Page 393: Windshield Wiper Blade Rubber
Stopper 3. Remove the wiper blade assembly by holding its pivot area and pushing it in the direction shown by the arrow while de- pressing the wiper blade stopper. 4. Install the wiper blade assembly to the wiper arm. Make sure that it locks in place. 5.
Page 394: Rear Window Wiper Blade Assembly
11-44 Maintenance and service with the grooves in the rubber and slide the blade rubber assembly into the metal support until it locks. Stopper 4. Be sure to position the claws at the end of the metal support between the stoppers on the rubber as shown.
Page 395: Rear Window Wiper Blade Rubber
& Rear window wiper blade rubber 1. Pull out the end of the blade rubber assembly to unlock it from the plastic support. 2. Pull the blade rubber assembly out of the plastic support. Metal spines 3. If the new blade rubber is not provided with two metal spines, remove the metal spines from the old blade rubber and install them in the new blade rubber.
Page 396: Battery
11-46 Maintenance and service ends. If the rubber is not retained properly, the wiper may scratch the rear window glass. 5. Install the wiper blade assembly to the wiper arm. Make sure that it locks in place. 6. Hold the wiper arm by hand and slowly lower it in position.
Page 397: Fuses
distilled water. Fuses CAUTION Never replace a fuse with one hav- ing a higher rating or with material other than a fuse because serious damage or a fire could result. The fuses are designed to melt during an overload to prevent damage to the wiring harness and electrical equipment.
Page 398 4. Pull out the fuse with the fuse puller. 5. Inspect the fuse. If it has blown, replace it with a spare fuse of the same rating. 6. If the same fuse blows again, this indicates that its system has a problem. Contact your SUBARU dealer for repairs.
Page 399: Main Fuse
If a main fuse blows after it is replaced, have the electrical system checked by your nearest SUBARU dealer. Installation of accessories Always consult your SUBARU dealer before installing fog lights or any other electrical equipment in your vehicle.
Page 400: Replacing Bulbs
11-50 Maintenance and service Replacing bulbs...
Page 401: Headlight
12V-16W . If headlight aiming is required, con- 12V-5W 168 (W5W) sult your SUBARU dealer for proper adjustment of the headlight aim. . It may be difficult to replace the bulbs. Have the bulbs replaced by your SUBARU dealer if necessary.
Page 402 11-52 Maintenance and service ! Low beam light bulbs Right-hand side 1. Use a screwdriver to undo the clips on the air intake duct, then remove the air intake duct. (right-hand side) Left-hand side 2. Use a screwdriver to remove the secured clip of the washer tank.
Page 403: Front Turn Signal/Parking And Front Side Marker Light
& Front turn signal/Parking and front side marker light It may be difficult to replace the bulbs. Have the bulbs replaced by your SUBARU dealer if necessary. & Front fog light (if equipped) It may be difficult to replace the bulbs.
Page 404 11-54 Maintenance and service Rear turn signal light Back-up light Brake/tail and rear side marker light 2. Remove the bulb holder from the rear combination light assembly by turning it counterclockwise. 3. Pull the bulb out of the bulb holder and replace it with a new one.
Page 405 3. Remove the upper and lower screws. Then, straightly slide the rear combination light assembly rearward and remove it from the vehicle. Brake/tail light Rear turn signal light Rear side marker light 4. Remove the bulb holder from the rear combination light assembly by turning it counterclockwise.
Page 406: Back-Up Light (Station Wagon)
Install the light cover on the rear gate. & License plate light ! Sedan It may be difficult to replace the bulbs. Have the bulbs replaced by your SUBARU dealer if necessary. ! Station wagon 1. Remove the mounting screws using a Phillips screwdriver.
Page 407: Dome Light
3. Pull the bulb out of the socket. Install a new bulb. 4. Reinstall the lens. 5. Tighten the mounting screws. & Dome light 1. Remove the lens by prying the edge of the lens with a flat-head screwdriver. 2. Turn the bulb until the flat surfaces at its ends are aligned vertically.
Page 408: Vanity Mirror Light
11-58 Maintenance and service 2. Turn the bulb until the flat surfaces at its ends are aligned vertically. Pull the bulb straight downward to remove it. 3. Install a new bulb. 4. Reinstall the lens. & Vanity mirror light 1. Remove the lens by prying the edge of the lens with a flat-head screwdriver.
Page 409: Cargo Area Light (Station Wagon)
2. Pull the bulb out of the socket. Install a new bulb. 3. Reinstall the cover. & High mount stop light (Sedan) It may be difficult to replace the bulbs. Have the bulbs replaced by your SUBARU dealer if necessary.
Page 410: Specifications
Specifications ... 12-2 Dimensions... Engine ... Electrical system... Capacities ... Tires ... Wheel alignment ... Fuses and circuits ... 12-2 Fuse panel located in the passenger compartment ... 12-3 Fuse panel located in the engine 12-3 compartment ... 12-4 Bulb chart... 12-5 Vehicle identification ...
Page 411: Specifications
12-2 Specifications Specifications These specifications are subject to change without notice. & Dimensions Item Sedan 2.5-liter Except 2.5GT 2.5GT spec.B spec.B Overall length 185.0 (4,700) Overall width 68.1 (1,730) Overall height 56.1 (1,425) (1,435) Wheel base 105.1 (2,670) Tread Front 58.9 (1,495) Rear 58.5 (1,485)
Page 412: Engine
& Engine Engine model EJ253 (2.5 L, SOHC, non-turbo) Engine type Horizontally opposed, liquid cooled 4 cylinder, Displacement cu-in (cc) Bore 6 Stroke in (mm) Compression ratio 10.0 : 1 Firing order & Electrical system Battery type and capacity 2.5 L models (5HR) 3.0 L models Alternator...
Page 413: Capacities
12-4 Specifications & Capacities Fuel tank Engine oil 2.5 L models 3.0 L models Transmission oil (MT) 5-speeds 6-speeds Transmission fluid (AT) 2.5 L non-turbo models 2.5 L turbo and 3.0 L models AT differential gear oil 2.5 L non-turbo models 2.5 L turbo and 3.0 L models Rear differential gear oil Turbo 6-speeds MT models...
Page 414: Tires
& Tires Tire size P205/55R16 16 6 6.5JJ Wheel size Pressure Front 32 psi (220 kPa, 2.2 kgf/cm Rear 30 psi (210 kPa, 2.1 kgf/cm Rear at – trailer tow- Temporary Size T135/80R16 spare tire Pressure *1: 2.5 GT Limited model *2: 3.0 R model &...
Page 415: Fuses And Circuits
12-6 Specifications Fuses and circuits & Fuse panel located in the passenger compartment Fuse Fuse Circuit panel rating Cargo fan Trailer hitch connector Empty Door locking Front wiper deicer relay Moonroof Combination meter 7.5A Remote control rear view mirrors Seat heater relay Vanity mirror light Combination meter Integrated unit...
Page 416 Fuse Fuse Circuit panel rating Cargo socket Position light Tail light Rear combination light Empty Illumination Seat heaters Back-up light 7.5A Headlight right side re- Cigarette lighter socket 7.5A Starter relay Air conditioner Rear window defogger relay coil Rear wiper Rear window washer Audio unit Clock...
Page 417: Fuse Panel Located In The Engine Compartment
12-8 Specifications & Fuse panel located in the engine compartment FWD socket (AT models with non-turbo 2.5 L engine) Main fuse Fuse Fuse Circuit panel rating ABS unit Vehicle dynamics control unit Main fan (3.0 L models) Secondary air combina- tion valve (turbo models) Sub fan (except 3.0 L models)
Page 418: Bulb Chart
Bulb chart Description Wattage Headlight Low beam 12V-55W High beam 12V-60W Front fog light 12V-51W 12V-27/8W Front turn signal/Parking and front side marker light Rear combination light Rear turn signal light (Se- 12V-21W dan) Brake/Tail and rear side 12V-21/5W marker (Sedan) Brake/Tail (Station wagon) 12V-21/5W Rear side marker (Station...
Page 419: Specifications
12-10 Specifications Description Wattage 12V-5W Trunk room light Cargo area light 12V-13W Dome light 12V-8W Map light 12V-8W Vanity mirror light 12V-3W Door step light 12V-3W Bulb No. 168 (W5W) – – – – –...
Page 420: Vehicle Identification
Vehicle identification 12-11 Specifications Emission control label Vehicle identification number Certification and bar code label Tire inflation pressure label Vehicle identification number plate Model number label Fuel label...
Page 421: Consumer Information And Reporting Safety Defects
Consumer information and Reporting safety defects For U.S.A..13-2 Tire information ... 13-2 Tire labeling ... Recommended tire inflation pressure... Glossary of tire terminology ... Tire care – maintenance and safety practices... Vehicle load limit – how to determine... Determining compatibility of tire and vehicle load capacities ...
Page 422: Consumer Information And Reporting Safety Defects
13-2 Consumer information and Reporting safety defects For U.S.A. The following information has been compiled according to Code of Federal Regulations “Title 49, Part 575”. Tire information & Tire labeling Many markings (e.g. Tire size, Tire Identification Number or TIN) are placed on the sidewall of a tire by tire manufacturers.
Page 423 the tire’s speed rating. Example: (6) Load Index: A numerical code which specifies the maximum load a tire can carry at the speed indicated by its speed symbol, at maximum inflation pressure. For example, “88” means 1,234 lbs (560 kg), “87” means 1,201 lbs (545 kg), “86”...
Page 424 13-4 Consumer information and Reporting safety defects ! Maximum load rating The load rating at the maximum permissible weight load for this tire. For example, “MAX. LOAD 730 kg (1609 LBS) @ 300 kpa (44 PSI) MAX. PRESS.” WARNING Maximum load rating applies only to the tire, not to the vehicle.
Page 425: Recommended Tire Inflation Pressure
& Recommended tire inflation pressure ! Recommended cold tire inflation pressure Recommended cold tire inflation pressure for your vehicle’s tires is as follows, Tire size P205/ 55R16 89H 60R16 97H 16 6 6.5JJ Wheel size Pres- Front 32 psi sure (220 kPa, 2.2 kgf/cm 2.2 kgf/cm...
Page 426: Glossary Of Tire Terminology
13-6 Consumer information and Reporting safety defects ! Vehicle placard The vehicle placard is affixed to the driver’s side B-pillar. Example: The vehicle placard shows original tire size, recommended cold tire inflation pressure on each tire at maximum loaded vehicle weight, seating capacity and loading infor- mation.
Page 427: Tire Care - Maintenance And Safety Practices
whitewall, bears white lettering or bears manufacturer, brand, and/or model name molding that is higher or deeper than the same molding on the other side- wall of the tire, or The outward facing sidewall of an asymmetrical tire that has a particular side that must al- ways face outward when mount- ing on a vehicle.
Page 428: Vehicle Load Limit - How To Determine
13-8 Consumer information and Reporting safety defects tires every 7,500 miles (12,000 km). Rotating the tires involves switch- ing the front and rear tires on the right-hand side of the vehicle and similarly switching the front and rear tires on the left-hand side of the vehicle.
Page 429 Calculate the available load ca- pacity by subtracting the total weight from the vehicle capacity weight of 800 lbs (363 kg). The result of step 2 shows that a further 95 lbs (43 kg) of cargo can be carried. Consumer information and Reporting safety defects Example 1B For example, if a person weighing 176 lbs (80 kg) now enters the...
Page 430 13-10 Consumer information and Reporting safety defects is indicated on the vehicle placard with the statement “The combined weight of occupants and cargo should never exceed 363 kg or 800 lbs”. For example, the vehicle has one occupant weighing 165 lbs (75 kg) plus cargo weighing 265 lbs (120 kg).
Page 431: Determining Compatibility Of Tire And Vehicle Load Capacities
The total weight now exceeds the capacity weight by 22 lbs (10 kg), so the cargo weight must be reduced by 22 lbs (10 kg) or more. & Determining compatibility of tire and vehicle load capaci- ties The sum of four tires’ maximum load ratings must exceed the max- imum loaded vehicle weight (“GVWR”).
Page 432: Uniform Tire Quality Grading Standards
13-12 Consumer information and Reporting safety defects available amount of cargo and luggage load capacity. For exam- ple, if the “XXX” amount equals 1,400 lbs (635 kg) and there will be five- 150 lbs (68 kg) passengers in your vehicle, the amount of avail- able cargo and luggage load capa- city is 650 lbs (1,400 −...
Page 433: Temperature A, B, C
However, NHTSA cannot become involved in individual problems between you, your dealer, or Subaru of America, Inc. To contact NHTSA, you may call the Vehicle Safety Hotline toll-free at 1-888-327-4236 (TTY: 1-800-424-9153); go to http://www.safercar.gov;...
Page 434 13-14 Consumer information and Reporting safety defects DC 20590. You can also obtain other information about motor ve- hicle safety from http://www.safercar.gov.
Page 435: Index
Index...
Page 436 14-2 Index ABS (Anti-lock Brake System) ... 7-35 Warning light ... 3-34, 7-36 Accessories... 5-4, 11-49 Accessory power outlet... 6-9 Active head restraint... 1-7 Air cleaner element ... 11-17 Air conditioner ... 4-7 Air filtration system... 4-13 Air flow selection... 4-2 Alarm system ...
Page 437 Capacities ... 12-4 Cargo area Cover ... 6-14 Light... 6-2 Tie-down hooks ... 6-17 Catalytic converter ... 8-3 Center Console ... 6-6 Ventilators ... 4-3 Center and side ventilators... 4-3 Changing Flat tire ... 9-4 Oil and oil filter ... 11-10 Charge warning light ...
Page 438 14-4 Index Disarming the alarm system ... 2-19 Disc brake pad wear warning indicators ... 7-35 Dome light ... 6-2, 11-57 Door Locks ... 2-5 Open warning light ... 3-36 Step light ... 11-58 Drive belts... 11-20 Driving All-Wheel Drive warning light ... 3-36 Car phone/cell phone ...
Page 439 Front turn signal/Parking and front side marker ... 11-53 Fuel ... 7-3 Economy hints... 8-2 Filler lid and cap ... 7-5 Gauge ... 3-6, 3-26 Requirements ... 7-3 Fuses ... 11-47 Fuses and circuits ... 12-6 GAWR (Gross Axle Weight Rating) ... 8-15 Gear position indicator ...
Page 440 14-6 Index Jump starting... 9-10 Number ... 2-2 Reminder chime... 3-5 Replacement ... 2-4 Keyless entry system ... 2-8 Keys ... 2-2 Leather seat materials ... 10-5 License plate light ... 11-56 Light Back-up (Sedan)... 11-53 Back-up (Station wagon)... 11-56 Brake/Tail (Station wagon)...
Page 441 New vehicle break-in driving... 8-2 Odometer... 3-25 Odometer/Trip meter ... 3-10 Off road driving... 8-6 Oil filter... 11-10 Oil level Engine... 11-9 Front differential gear ... 11-24 Manual transmission... 11-21 Rear differential ... 11-25 Oil pressure warning light... 3-32 Outside mirrors ... 3-57 Outside temperature indicator ...
Page 442 14-8 Index Refueling ... 7-5 Remote engine start system ... 7-11 Remote keyless entry system ... 2-8 Replacement Brake pad and lining ... 11-32 Wiper blades ... 11-42 Replacing Air cleaner element ... 11-18 Battery (remote keyless entry system) ... 2-11 Lost transmitters (remote keyless entry system) ...
Page 443 Speedometer... 3-6, 3-24 SPORT mode indicator light ... 3-38 Curtain airbag... 1-56 Frontal airbag ... 1-45 Side airbag ... 1-56 SRS airbag (Supplemental Restraint System airbag) ... 4, 1-40 SRS airbag system Monitors... 1-63 Servicing... 1-65 Warning light ... 3-30 Starting the engine ...
Page 444 14-10 Index Turn signal Indicator lights ... 3-40 Lever... 3-47 Under-floor storage compartment ... 6-18 Valet mode... 2-19 Vanity mirror Light... 11-58 Vehicle Capacity weight ... 8-14 Identification ... 12-11 Symbols ... 2 Vehicle Dynamics Control OFF indicator light... 7-40 OFF switch ...
Page 445 134...
Page 446 & Fuel: ! 2.5 L non-turbo models Use only unleaded gasoline with an octane rating of 87 AKI or higher. ! 2.5 L turbo models Use premium unleaded gasoline with an octane rating of 91 AKI or higher. For temporary purposes if premium unleaded gasoline is not available, you may use regular unleaded gasoline with an octane rating of 87 AKI or higher.
Page 447 & Cold tire pressure: Tire size P205/55R16 16 6 6.5JJ Wheel size Pressure Front 32 psi (220 kPa, 2.2 kgf/ Rear 30 psi (210 kPa, 2.1 kgf/ – Rear at trailer tow- Temporary Size T135/80R16 spare tire Pressure *1: 2.5 GT Limited model *2: 3.0 R model P225/60R16 P205/50R17...

This manual is also suitable for:

2009 outback Legacy sedan Legacy station wagon Outback station wagon

Subaru 2009 Legacy Owner's Manual

Table of Contents

Table of Contents

Front Seats

Seat Heater (if Equipped)

Rear Seats

Armrest (if Equipped)

Seatbelts

Front Seatbelt Pretensioners

Child Restraint Systems

SRS Airbag (Supplemental Restraint System Airbag)

Keys and Doors

Keys

Immobilizer

Door Locks

Power Door Locking Switches

Remote Keyless Entry System

Alarm System

Child Safety Locks

Windows

Trunk Lid (Sedan)

Rear Gate (Station Wagon)

Moonroof (if Equipped)

Abs Warning Light

Climate Control

Ventilator

Manual Climate Control System (if Equipped)

Automatic Climate Control System (if Equipped)

Operating Tips for Heater and Air Conditioner

Air Filtration System

Audio

Antenna System

XM Tm

Installation of Accessories

Audio Set

Power and Sound Controls

FM/AM Radio Operation

Satellite Radio Operation (if Equipped)

CD Player Operation

AUX Unit Operation

Audio Control Buttons (if Equipped)

Precautions to Observe When Handling a Compact Disc

Interior Equipment

Interior Light

Map Light

Sun Visors

Storage Compartment

Cup Holder

Accessory Power Outlets

Ashtray (Canada Only - if Equipped)

Coat Hook

Shopping Bag Hook

Floor Mat

Cargo Area Cover (if Equipped)

Convenient Tie-Down Hooks (if Equipped)

Stowage Boxes (Station Wagon)

Under-Floor Storage Compartment

Homelink® Wireless Control System (if Equipped)

Quick Links

Chapters

Related Manuals for Subaru 2009 Legacy

Summary of Contents for Subaru 2009 Legacy