Table of Contents
Advertisement
5.1.4. PIP menu
Picture
Sub mode
Screen
PIP size
Audio
PIP position
PIP
PIP change
Configuration 1
PIP source
PIP audio
PIP reset
Sub mode
Select the PIP (Picture-in-Picture) mode.
Choose from:
{Off}/{PIP}/{POP}/{Quick
{PBP}.
PIP size
Select the size of the sub picture in the PIP
(Picture-in-Picture) mode.
Choose from: {Small} / {Medium} / {Large}.
PIP position
Select the position of the sub picture in the PIP
(Picture-in-Picture) mode.
{Bottom-Right} / {Bottom-Left} / {Top-Right} /
{Top-Left}
PIP change
Exchange Main and PIP/POP/PBP/Quick swap
input signal.
PIP Source
Select the input signal for the sub picture.
PIP audio
Select the audio source in the Sub mode.
•
{Main} - Select audio from the main picture
•
{Sub} - Select audio from the sub picture.
PIP reset
Reset all settings in the PIP menu to factory preset
values.
NOTES
:
•
The PIP function is available only for certain
signal source combinations as shown in the table
below.
•
The availability of the PIP function will also
depend on the resolution of the input signal
being used.
Off
Small
Bottom-Right
Action
VGA
Main
Action
swap}/
24
HDMI1
HDMI2
DVI DisplayPort VGA MediaPlayer Browser
HDMI1
O
X
X
O
HDMI2
X
O
X
O
DVI
X
X
O
O
DisplayPort
O
O
O
O
VGA
O
O
X
O
Media
X
X
X
O
Player
Browser
X
X
X
O
PDF Player
X
X
X
O
Custom
X
X
X
O
(O: PIP function available, X: PIP function
unavailable)
5.1.5. Config1 menu
Picture
Switch on state
Screen
Panel saving
Audio
RS232 routing
PIP
Boot on source
Configuration 1
WOL
Power LED light
Network
Configuration1 reset
Factory reset
Switch on state
Select the display status used for the next time
you connect the power cord.
•
{Power off}
- The display will remain off when
the power cord is connected to a wall outlet.
•
{Forced
on} - The display will turn on when the
power cord is connected to a wall outlet.
•
{Last
status} - The display will return to the
previous power status (on/off/standby) when
removing and replacing the power cord.
Panel saving
Choose to enable the panel saving functions and
thus reduce the risk of "image persistence" or
"ghost-imaging".
•
{Brightness}
- Select {On} and the image
brightness will be reduced to an appropriate
level. The Brightness setting in the Picture menu
will be unavailable when selected.
•
{Pixel
shift} - Select the time interval ({Auto} /
~
900} Seconds/ {Off}) for the display to slightly
expand the image size and shift the position of
pixels in four directions (up, down, left, or right).
Activating Pixel Shift will disable H Position, V
Position and Zoom Mode in the Screen Menu.
RS232 Routing
Select the network control port.
Choose from: {RS232} / {LAN->RS232}.
Boot on Source
Choose to select source when boot up.
Input: select input source when bootup.
PDF
Custom
Player
O
X
X
X
X
O
X
X
X
X
X
X
X
X
X
O
O
O
O
O
O
O
O
O
O
O
O
X
X
X
O
X
O
X
X
O
X
X
O
X
O
X
X
X
O
Last status
Action
RS232
Action
Off
On
On
Action
Action
{10
Advertisement
Table of Contents
Troubleshooting
