Table of Contents
Advertisement
01GB00iLX-F2611EOM.book Page 19 Thursday, September 10, 2020 2:05 PM
5
To store the adjusted setting value, touch and hold
[Preset 1], [Preset 2], or [Preset 3] for at least 2 seconds.
• Settings exceeding the frequency of adjacent bands are not available.
• While adjusting the Graphic EQ, you should consider the frequency
response of the connected speakers.
• When the Graphic EQ is adjusted, the Equalizer Presets are overridden.
• When Equalizer Presets is set, the linked Graphic EQ settings are also
changed. We recommend storing Graphic EQ settings in a Preset in
advance.
• Touch [Flat] to initialize all values.
Calling the Graphic EQ adjusted value
Touch [Preset 1], [Preset 2], or [Preset 3].
The setting stored in the Preset will be recalled.
Time Correction Settings
[Time Correction] is selected on the Sound Setup Menu screen.
Before performing the following procedures, see "About Time
Correction" (page 21).
Correction mode
Setting item:
Time Correction
1
Touch [Time Correction] on the Sound Setup menu
screen.
2
Touch the Correction mode button, and then select [ms],
[cm] or [inch].
3
Touch [ ] or [ ] for each speaker to adjust the time or
distance.
0.0 msec to 9.9 msec (0.1 msec/step)
0.0 cm (0.0 inch) to 336.6 cm (132.56 inch) (3.4 cm/step)
All speaker setting values are adjustable in the range of 20 ms or
680 cm.
4
To store the adjusted setting value, touch and hold
[Preset 1], [Preset 2], or [Preset 3] for at least 2 seconds.
• Touch [Flat] to set all values to 0.0.
• If the Rear Speaker setting is Off, the Rear Speaker setting cannot be
edited (page 20).
• If the Subwoofer setting is Off, the Subwoofer setting cannot be edited
(page 20).
Calling the Time Correction Value
Calling the pre-set time correction value.
Touch [Preset 1], [Preset 2], or [Preset 3] on the time
correction screen.
The setting stored in the Preset will be recalled.
01GB04Setup.fm
Crossover Settings (X-Over)
[X-Over] is selected on the Sound Setup Menu screen.
Before performing the following procedures, see "About the Crossover"
(page 21).
Setting item:
X-Over
1
Touch [X-Over] on the Sound Setup menu screen.
2
Touch [Channel], and then select [Front HPF], [Rear
HPF] or [SubW.LPF].
3
Adjust the crossover to your preference.
Selecting the Cut-Off Frequency
Touch [ ] or [ ] of "Freq. " (Frequency), and then select the cut-
off frequency.
Setting contents:
20.0 / 25.0 / 31.5 / 40.0 / 50.0 / 63.0 / 80.0 (Initial setting) / 100.0 / 125.0 /
160.0 / 200.0 Hz
Adjusting the Slope
Touch [ ] or [ ] of "Slope", and then adjust the HPF or LPF slope.
Setting contents:
0 (Initial setting) / 6 / 12 / 18 / 24 dB/oct.
Adjusting the Level
Touch [ ] or [ ] of "Level", and then adjust the HPF or LPF level.
Setting contents:
-12 to 0 dB (Initial setting: 0)
4
Repeat steps 2 to 3 to make adjustment to the other
channels.
5
To store the adjusted setting value, touch and hold
[Preset 1], [Preset 2], or [Preset 3] for at least 2 seconds.
• Touch [Flat] to initialize all values.
• If the Rear Speaker setting is Off, the Rear Speaker setting cannot be
edited (page 20).
• If the Subwoofer setting is Off, the Subwoofer setting cannot be edited
(page 20).
• While adjusting the X-Over you should consider the frequency response
of the connected speakers.
Calling the X-Over adjusted value
Touch [Preset 1], [Preset 2], or [Preset 3].
The setting stored in the Preset will be recalled.
ALPINE iLX-F2611E/iLX-F269E M3514725010 (EN)
Channel
19
-EN
Advertisement
Table of Contents
