Cabinet Disassembly Instructions - Philips 43PFL4901/F7 Service Manual

CABINET DISASSEMBLY INSTRUCTIONS

Screw Torque Specification
Ref. Part
Part Name
No. Number
SCREW F-PAN BLACK_NI
L10 GCHP3120
+P-TITE M3X12.0
SCREW BIND 3CHROM
L23 GBJS3060
+S-TITE M3X6.0
SCREW F-PAN BLACK_NI
L28 GCHS3080
+S-TITE M3X8.0
L76 2EML00004 SCREW M3X7 LOW HEAD
STAND SCREW KIT
SSK1 1ESA34649 (SEMS-SW PAN BLACK_NI
+ M4X20.0)
* For reference
1. Disassembly Flowchart
This flowchart indicates the disassembly steps for the
cabinet parts and the CBA in order to gain access to
items to be serviced. When reassembling, follow the
steps in reverse order. Bend, route and dress the
cables as they were.
[1] Stand
Assembly
[3] Power Supply
[2] Rear Cabinet
CBA
[6] Speaker [5] Stand Bracket
[7] Speaker [10] IR Sensor
Holder L,R
CBA Unit
[11] LCD Panel
Assembly
[12] Front
Cabinet*4
2. Disassembly Method
Step/
Fig.
Loc. Part
No.
No.
Stand
[1] D1 3(S-1)
Assembly
Rear
[2] D1 14(S-2), 9(S-3)
Cabinet
Power 5(S-4), CN501,
D2
[3] Supply CN601, CN1101,
W1
CBA CN1201
4(S-5), CN3501,
Digital Main D2
[4] CN3801, CN3901,
CBA Unit W1
Jack Holder
Tightening
Torque
5.2±0.9lb·in
6.5±0.9lb·in
5.2±0.9lb·in
(approx.
*
8.7±0.9lb·in)
[4] Digital Main
CBA Unit
[8] Function
CBA Unit
[9] T-CON Holder
Removal Note
---
---
---
---
4-1
Step/
Fig.
Loc. Part
No.
No.
Stand
[5] D3 ---------------
Bracket
[6] Speaker D3 ----------------
Speaker
[7] D3 2(S-6)
Holder L,R
CN4051, Function
Function D3
[8] Knob, Knob Frame,
CBA Unit W1
Hook
T-CON 3(S-7), T-CON Module,
[9] D3
Holder FFC Cable
IR Sensor D3
[10] Sensor Shield, Hook
CBA Unit W1
Decoration Plate, LED
LCD Panel
D4 Lens, Leading Edge
Assembly *5
Cover, Hook
[11]
LCD Panel
D5 8(S-8)
Assembly *4
Decoration Plate, LED
Lens, Leading Edge
Front Cover, Hook,
[12] *4 D5
Cabinet Cell Cushion LR,
Cell Cushion UD,
Double Side Tape
  
(1) (2) (3)
*4 : 43PFL4901/F7
*5 : 43PFL4901/F8
Note:
(1) Order of steps in procedure. When reassembling,
follow the steps in reverse order. These numbers
are also used as the Identification (location) No. of
parts in figures.
(2) Parts to be removed or installed.
(3) Fig. No. showing procedure of part location
(4) Identification of parts to be removed, unhooked,
unlocked, released, unplugged, unclamped, or
desoldered.
P = Spring, L = Locking Tab, S = Screw,
H = Hex Screw, CN = Connector
e.g. 2(S-2) = two Screws of (S-2),
2(L-2) = two Locking Tabs of (L-2)
(5) Refer to the following "Reference Notes in the
Table."
Removal Note
---
---
---
2
1
2
1
3
 
(4) (5)
PL15.13-A_DC