Page 1 2005 Buick Rendezvous Owner Manual Seats and Restraint Systems ... 1-1 Front Seats ... 1-3 Rear Seats ... 1-8 Safety Belts ... 1-20 Child Restraints ... 1-43 Airbag System ... 1-67 Restraint System Check ... 1-83 Features and Controls ... 2-1 Keys ...
Page 2: How To Use This Manual
GENERAL MOTORS, GM, the GM Emblem, BUICK, the BUICK Emblem, and the name RENDEZVOUS are registered trademarks of General Motors Corporation. This manual includes the latest information at the time it was printed. We reserve the right to make changes after that time without notice.
Page 3 Index A good place to quickly locate information about the vehicle is the Index in the back of the manual. It is an alphabetical list of what is in the manual and the page number where it can be found. Safety Warnings and Symbols There are a number of safety cautions in this book.
Page 4 Vehicle Damage Warnings Also, in this manual you will ﬁnd these notices: Notice: These mean there is something that could damage your vehicle. A notice tells about something that can damage the vehicle. Many times, this damage would not be covered by your vehicle’s warranty, and it could be costly.
Page 5 These are some examples of symbols that may be found on the vehicle:...
Page 6 NOTES...
Page 7: Seats And Restraint Systems
Section 1 Front Seats ...1-3 Manual Passenger Seat ...1-3 Four-Way Manual Driver Seat ...1-3 Six-Way Power Seats ...1-4 Manual Lumbar ...1-5 Heated Seats ...1-5 Reclining Seatbacks ...1-6 Head Restraints ...1-7 Rear Seats ...1-8 Rear Seat Operation ...1-8 Split Bench Seats ...1-8 Captain Chairs ...1-13 Stowable Seat ...1-17 Safety Belts ...1-20...
Page 8: Table Of Contents
Section 1 What Will You See After an Airbag Inﬂates? ...1-76 Passenger Sensing System ...1-77 Servicing Your Airbag-Equipped Vehicle ...1-82 Adding Equipment to Your Airbag-Equipped Vehicle ...1-82 Seats and Restraint Systems Restraint System Check ...1-83 Checking Your Restraint Systems ...1-83 Replacing Restraint System Parts After a Crash ...1-83...
Page 9: Front Seats
Front Seats Manual Passenger Seat Pull up on the lever, located on the front of the seat, to unlock and move the seat. Slide the seat to where you want it and release the lever. To make sure the seat is locked into place, try to move the seat back and forth with your body.
Page 10: Six-Way Power Seats
To make sure the seat is locked into place, try to move the seat back and forth with your body. To raise the seat, pull up on the lever located on the front right side of the seat. To lower the seat, push the lever down. Adjust the seat and release the lever.
Page 11: Manual Lumbar
Manual Lumbar The knob that controls this feature is located on the outboard sides of the driver’s and front passenger’s seats. Turn the knob toward the front of the vehicle to increase lumbar support. Turn the knob toward the rear of the vehicle to decrease lumbar support.
Page 12: Reclining Seatbacks
Reclining Seatbacks To adjust a seatback, pull up on the lever located on the outboard side of the driver’s or front passenger’s seats. Release the lever to lock the seatback where you want it. Push and pull on the seat to make sure it’s locked into position.
Page 13: Head Restraints
CAUTION: Sitting in a reclined position when your vehicle is in motion can be dangerous. Even if you buckle up, your safety belts can not do their job when you are reclined like this. The shoulder belt can not do its job because it will not be against your body.
Page 14: Rear Seats
Rear Seats Rear Seat Operation The rear seats in your vehicle have seat operating features to adjust, fold, remove and reinstall the seats. By using the seat operating procedures, in the correct order, you can easily remove the seats from your vehicle.
Page 15 To recline the seatback on up-level split bench seats, push forward on the recliner lever located on the outboard side of the seatback. Up-Level Move the seatback to the desired position. It is easier to raise or lower the seatback if you lean forward and take the weight off the seatback.
Page 16 Base-Level 4. For base-level split bench seats, pull the lever at the base of the seat on the outboard side to release the rear latches from the ﬂoor pins and ﬂip the seat forward. For up-level split bench seats, continue pushing forward on the recliner lever to release the rear latches from the ﬂoor pins and ﬂip the seat forward.
Page 17: Replacing The Split Bench Seat
Replacing the Split Bench Seat CAUTION: If the seatback is not locked, it could move forward in a sudden stop or crash. That could cause injury to the person sitting there. Always press rearward on the seatback to be sure it is locked.
Page 18 1. Squeeze the angled latch release bar toward the straight crossbar while placing the front hooks of the bench seat onto the front two ﬂoor pins. 2. Make sure that the bench seat is angled so that the front hooks clear the ﬂoor pins.
Page 19: Captain Chairs
Captain Chairs If your vehicle has captain’s chairs, the chairs and seatbacks can be adjusted forward or rearward. Adjusting the Captain’s Chairs (Second Row) To adjust the second row captain’s chairs, use the adjustment bar located below the front of each seat. Lift up the lever to slide the seat forward or rearward.
Page 20 Removing the Captain’s Chairs 1. Make sure that the seatback is in the upright position. 2. Lift the seatback recliner lever to fold the seatback forward. 3. Pull the nylon strap behind the chair to release the rear hooks from the ﬂoor pins. 1-14 4.
Page 21 Replacing the Captain’s Chairs CAUTION: If the seatback is not locked, it could move forward in a sudden stop or crash. That could cause injury to the person sitting there. Always press rearward on the seatback to be sure it is locked.
Page 22 1. Hook the front latches over the front ﬂoor pins. 1-16 2. Push the rear of the seat down to lock the rear latches onto the rear set of ﬂoor pins. 3. Push and pull on the seat to check that it is properly attached.
Page 23: Stowable Seat
Stowable Seat The stowable seat is a two passenger bench seat and comes with the rear convenience center. See Rear Convenience Center on page 2-44 for more information. The stowable seat can be removed and replaced or, with the seatback folded, it can lie ﬂat with the convenience center.
Page 24: Removing The Stowable Seat
Removing the Stowable Seat 1. Remove the convenience center, if it is in the vehicle. See Rear Convenience Center on page 2-44 for more information. 2. Make sure all items are off the stowable seat. 3. If the seatback is down, put the seatback in its upright position before removing the seat.
Page 25 CAUTION: A safety belt that is improperly routed, not properly attached, or twisted will not provide the protection needed in a crash. The person wearing the belt could be seriously injured. After installing the seat, always check to be sure that the safety belts are properly routed and attached, and are not twisted.
Page 26: Safety Belts
Safety Belts Safety Belts: They Are for Everyone This part of the manual tells you how to use safety belts properly. It also tells you some things you should not do with safety belts. CAUTION: Do not let anyone ride where he or she can not wear a safety belt properly.
Page 27: Why Safety Belts Work
Your vehicle has a light that comes on as a reminder to buckle up. See Safety Belt Reminder Light on page 3-41. In most states and in all Canadian provinces, the law says to wear safety belts. Here is why: They work. You never know if you will be in a crash.
Page 28 Put someone on it. 1-22 Get it up to speed. Then stop the vehicle. The rider does not stop.
Page 29 The person keeps going until stopped by something. In or the instrument panel... a real vehicle, it could be the windshield... 1-23...
Page 30: Questions And Answers About Safety Belts
or the safety belts! With safety belts, you slow down as the vehicle does. You get more time to stop. You stop over more distance, and your strongest bones take the forces. That is why safety belts make such good sense. 1-24 Questions and Answers About Safety Belts...
Page 31: How To Wear Safety Belts Properly
If I am a good driver, and I never drive far from home, why should I wear safety belts? You may be an excellent driver, but if you are in an accident — even one that is not your fault — you and your passengers can be hurt.
Page 32 3. Pick up the latch plate and pull the belt across you. Do not let it get twisted. The shoulder belt may lock if you pull the belt across you very quickly. If this happens, let the belt go back slightly to unlock it. Then pull the belt across you more slowly.
Page 33 5. To make the lap part tight, pull down on the buckle end of the belt as you pull up on the shoulder belt. The lap part of the belt should be worn low and snug on the hips, just touching the thighs. In a crash, this applies force to the strong pelvic bones.
Page 34 What is wrong with this? The shoulder belt is too loose. It will not give nearly as much protection this way. 1-28 CAUTION: You can be seriously hurt if your shoulder belt is too loose. In a crash, you would move forward too much, which could increase injury.
Page 35 What is wrong with this? The belt is buckled in the wrong place. CAUTION: You can be seriously injured if your belt is buckled in the wrong place like this. In a crash, the belt would go up over your abdomen. The belt forces would be there, not at the pelvic bones.
Page 36 What is wrong with this? The belt is over an armrest. 1-30 CAUTION: You can be seriously injured if your belt goes over an armrest like this. The belt would be much too high. In a crash, you can slide under the belt.
Page 37 What is wrong with this? The shoulder belt is worn under the arm. It should be worn over the shoulder at all times. CAUTION: You can be seriously injured if you wear the shoulder belt under your arm. In a crash, your body would move too far forward, which would increase the chance of head and neck injury.
Page 38 What is wrong with this? The belt is twisted across the body. 1-32 CAUTION: You can be seriously injured by a twisted belt. In a crash, you would not have the full width of the belt to spread impact forces. If a belt is twisted, make it straight so it can work properly, or ask your dealer to ﬁx it.
Page 39: Shoulder Belt Height Adjustment
To unlatch the belt, just push the button on the buckle. The belt should go back out of the way. Before you close the door, be sure the belt is out of the way. If you slam the door on it, you can damage both the belt and your vehicle.
Page 40: Safety Belt Use During Pregnancy
Safety Belt Use During Pregnancy Safety belts work for everyone, including pregnant women. Like all occupants, they are more likely to be seriously injured if they do not wear safety belts. A pregnant woman should wear a lap-shoulder belt, and the lap portion should be worn as low as possible, below the rounding, throughout the pregnancy.
Page 41 Lap-Shoulder Belt 1. Pick up the latch plate and pull the belt across you. Do not let it get twisted. The shoulder belt may lock if you pull the belt across you very quickly. If this happens, let the belt go back slightly to unlock it.
Page 42 3. To make the lap part tight, pull down on the buckle end of the belt as you pull up on the shoulder part. The lap part of the belt should be worn low and snug on the hips, just touching the thighs. In a crash, this applies force to the pelvic bones.
Page 43 The safety belt locks if there is a sudden stop or a crash, or if you pull the belt very quickly out of the retractor. CAUTION: You can be seriously hurt if your shoulder belt is too loose. In a crash, you would move forward too much, which could increase injury.
Page 44: Center Rear Passenger Position
Center Rear Passenger Position Lap-Shoulder Belt If your vehicle has a bench seat, someone can sit in the center position. When you sit in the center seating position, you have a lap safety belt, which has no retractor. You also have a shoulder belt, which has a retractor.
Page 45 2. Insert the metal knob on the shoulder belt into the 3. To make the lap belt longer, tilt the latch plate and keyhole on the lap belt buckle as shown. Be sure to pull it along the belt. slide the shoulder belt part into the keyhole until it locks into place.
Page 46 To make the belt shorter, pull its free end as shown until the belt is snug 4. Buckle, position and release the lap-shoulder belt the same way as the other lap-shoulder belts. If the belt is not long enough, see Safety Belt Extender on page 1-42.
Page 47 Here is how to install a comfort guide and use the safety belt: 2. Attach the elastic cord to the comfort guide on the center passenger shoulder belt. Second Row Center Position For second row center position do the following: 1.
Page 48: Safety Belt Pretensioners
3. Be sure that the belt is not twisted and it lies ﬂat. The guide must be on top of the belt. 4. Buckle, position and release the safety belt as described in Center Rear Passenger Position on page 1-38. Make sure that the shoulder belt crosses the shoulder.
Page 49: Child Restraints
Child Restraints Older Children Older children who have outgrown booster seats should wear the vehicle’s safety belts. What is the proper way to wear safety belts? If possible, an older child should wear a lap-shoulder belt and get the additional restraint a shoulder belt can provide.
Page 50 CAUTION: Never do this. Here two children are wearing the same belt. The belt can not properly spread the impact forces. In a crash, the two children can be crushed together and seriously injured. A belt must be used by only one person at a time. 1-44 What if a child is wearing a lap-shoulder belt, but the child is so small that the shoulder belt...
Page 51: Infants And Young Children
CAUTION: Never do this. Here a child is sitting in a seat that has a lap-shoulder belt, but the shoulder part is behind the child. If the child wears the belt in this way, in a crash the child might slide under the belt.
Page 52 CAUTION: People should never hold a baby in their arms while riding in a vehicle. A baby does not weigh much — until a crash. During a crash a baby will become so heavy it is not possible to hold it. For example, in a crash at only 25 mph (40 km/h), a 12-lb (5.5 kg) baby will suddenly become a 240-lb (110 kg) force on a person’s arms.
Page 53 What are the different types of add-on child restraints? Add-on child restraints, which are purchased by the vehicle’s owner, are available in four basic types. Selection of a particular restraint should take into consideration not only the child’s weight, height and age but also whether or not the restraint will be compatible with the motor vehicle in which it will be used.
Page 54: Child Restraint Systems
CAUTION: The body structure of a young child is quite unlike that of an adult or older child, for whom the safety belts are designed. A young child’s hip bones are still so small that the vehicle’s regular safety belt may not remain low on the hip bones, as it should.
Page 55 A rear-facing infant seat (B) provides restraint with the seating surface against the back of the infant. The harness system holds the infant in place and, in a crash, acts to keep the infant positioned in the restraint. A forward-facing child seat (C-E) provides restraint for the child’s body with the harness and also sometimes with surfaces such as T-shaped or shelf-like shields.
Page 56 A booster seat (F-G) is a child restraint designed to improve the ﬁt of the vehicle’s safety belt system. Some booster seats have a shoulder belt positioner, and some high-back booster seats have a ﬁve-point harness. A booster seat can also help a child to see out the window. 1-50 How do child restraints work? A child restraint system is any device designed for...
Page 57 One system, the three-point harness, has straps that come down over each of the infant’s shoulders and buckle together at the crotch. The ﬁve-point harness system has two shoulder straps, two hip straps and a crotch strap. A shield may take the place of hip straps.
Page 58: Where To Put The Restraint
Where to Put the Restraint Accident statistics show that children are safer if they are restrained in the rear rather than the front seat. General Motors recommends that child restraints be secured in a rear seat, including an infant riding in a rear-facing infant seat, a child riding in a forward-facing child seat and an older child riding in a booster seat.
Page 59: Top Strap
Top Strap Some child restraints have a top strap, or “top tether.” It can help restrain the child restraint during a collision. For it to work, a top strap must be properly anchored to the vehicle. Some top strap-equipped child restraints are designed for use with or without the top strap being anchored.
Page 60 Top Strap Anchor Location If you are using a top strap-equipped child restraint in the second row center bench seat and need to temporarily transport a ﬂat tire for repair, move the child restraint to a rear seat outboard position. See Securing a Child Restraint in a Rear Outside Seat Position on page 1-60 for more on this, including important safety information.
Page 61 Second Row Outside Position Bench Seat Second Row Center Position Bench Seat without Third Row Seat 1-55...
Page 62 Your vehicle has top strap anchors already installed for the rear seating positions. An anchor bar for a top strap is located at the rear of the seat cushion for each second row outboard seating position. The anchor bar for the center position bench seat is located on the ﬂoor behind the second row seats.
Page 63 Second Row Center Position Bench Seat with Third Row Seat Folded Down If the vehicle has a third row seat and the seatback is folded, there is an anchor on the back of the third row seat for the second row center position bench seat. Third Row Passenger’s Side Outside Position There is also a top strap anchor for the third row passenger’s side outside position.
Page 64 Lower Anchorages and Top Tethers for Children (LATCH System) Your vehicle has the LATCH system. You will ﬁnd anchors in the second row outside passenger positions. This system, designed to make installation of child restraints easier, does not use the vehicle’s safety belts. Instead, it uses vehicle anchors and child restraint attachments to secure the restraints.
Page 65 A. Lower Anchorage B. Lower Anchorage In order to use the LATCH system in your vehicle, you need a child restraint designed for that system. To assist you in locating the lower anchors for this child restraint system, each seating position with the LATCH system has a label on the seatback.
Page 66: Securing A Child Restraint Designed For The Latch System
Securing a Child Restraint Designed for the LATCH System 1. Find the LATCH anchorages for the seating position you want to use, where the bottom of the seatback meets the back of the seat cushion. See Lower Anchorages and Top Tethers for Children (LATCH System) on page 1-58.
Page 67 Tilt the latch plate to adjust the belt if needed. 3. Buckle the belt. Make sure the release button is positioned so you would be able to unbuckle the safety belt quickly if you ever had to. 1-61...
Page 68: Securing A Child Restraint In A Center Rear Seat Position
4. To tighten the belt, push down on the child restraint, pull the shoulder portion of the belt to tighten the lap portion of the belt and feed the shoulder belt back into the retractor. If you are using a forward-facing child restraint, you may ﬁnd it helpful to use your knee to push down on the child restraint as you tighten the belt.
Page 69 1. Make the belt as long as possible by tilting the latch plate and pulling it along the belt. 2. Put the restraint on the seat. 3. Run the vehicle’s safety belt through or around the restraint. The child restraint instructions will show you how.
Page 70: Securing A Child Restraint In The Right Front Seat Position
To remove the child restraint, just unbuckle the vehicle’s safety belt. When you remove the child restraint, be sure to reconnect the lap and shoulder parts of the belt so they will be ready to work for an adult or larger child passenger.
Page 71 You will be using the lap-shoulder belt to secure the child restraint in this position. See Top Strap on page 1-53 if your child restraint has one. Be sure to follow the instructions that came with the child restraint. Secure the child in the child restraint when and as the instructions say.
Page 72 5. To tighten the belt, push down on the child restraint, pull the shoulder portion of the belt to tighten the lap portion of the belt and feed the shoulder belt back into the retractor. If you are using a forward-facing child restraint, you may ﬁnd it helpful to use your knee to push down on the child restraint as you tighten the belt.
Page 73: Airbag System
Airbag System Your vehicle has airbags — a frontal airbag for the driver and another frontal airbag for the right front passenger. Your vehicle may also have side impact airbags. Side impact airbags are available for the driver and right front passenger. If your vehicle has a side impact airbag for the driver and/or the right front passenger, the words AIR BAG will appear on the airbag covering on the side of the...
Page 74 Here are the most important things to know about the airbag system: CAUTION: You can be severely injured or killed in a crash if you are not wearing your safety belt — even if you have airbags. Wearing your safety belt during a crash helps reduce your chance of hitting things inside the vehicle or being ejected from it.
Page 75 CAUTION: Both frontal and side impact airbags inﬂate with great force, faster than the blink of an eye. If you are too close to an inﬂating airbag, as you would be if you were leaning forward, it could seriously injure you. Safety belts help keep you in position for airbag inﬂation before and during a crash.
Page 76: Where Are The Airbags
There is an airbag readiness light on the instrument panel cluster, which shows the airbag symbol. The system checks the airbag electrical system for malfunctions. The light tells you if there is an electrical problem. See Airbag Readiness Light on page 3-41 for more information.
Page 77 The right front passenger’s frontal airbag is in the instrument panel on the passenger’s side. If your vehicle has one, the driver’s side impact airbag is in the side of the driver’s seatback closest to the door. 1-71...
Page 78 If your vehicle has one, the right front passenger’s side impact airbag is in the side of the passenger’s seatback closest to the door. 1-72 CAUTION: If something is between an occupant and an airbag, the airbag might not inﬂate properly or it might force the object into that person causing severe injury or even death.
Page 79: When Should An Airbag Inﬂate
When Should an Airbag Inﬂate? The driver’s and right front passenger’s frontal airbags are designed to inﬂate in moderate to severe frontal or near-frontal crashes. But they are designed to inﬂate only if the impact exceeds a predetermined deployment threshold. Deployment thresholds take into account a variety of desired deployment and non-deployment events and are used to predict how severe a crash is likely to be in time for the airbags to inﬂate and help...
Page 80 Airbags may inﬂate at different crash speeds. For example: • If the vehicle hits a stationary object, the airbag could inﬂate at a different crash speed than if the object were moving. • If the object deforms, the airbag could inﬂate at a different crash speed than if the object does not deform.
Page 81: What Makes An Airbag Inﬂate
What Makes an Airbag Inﬂate? In an impact of sufficient severity, the airbag sensing system detects that the vehicle is in a crash. For both frontal and side impact airbags, the sensing system triggers a release of gas from the inﬂator, which inﬂates the airbag.
Page 82: What Will You See After An Airbag Inﬂates
What Will You See After an Airbag Inﬂates? After the airbag inﬂates, it quickly deﬂates, so quickly that some people may not even realize the airbag inﬂated. Some components of the airbag module will be hot for a short time. These components include the steering wheel hub for the driver’s frontal airbag and the instrument panel for the right front passenger’s frontal airbag.
Page 83: Passenger Sensing System
• Your vehicle is equipped with a crash sensing and diagnostic module which records information after a crash. See Vehicle Data Collection and Event Data Recorders on page 7-10. • Let only qualiﬁed technicians work on your airbag system. Improper service can mean that an airbag system will not work properly.
Page 84 The passenger sensing system will turn off the right front passenger’s frontal airbag under certain conditions. The driver’s airbag and the side airbags are not part of the passenger sensing system. The passenger sensing system works with sensors that are part of the right front passenger’s seat and safety belt.
Page 85 The passenger sensing system is designed to turn off the right front passenger’s frontal airbag if: • the right front passenger seat is unoccupied • the system determines that an infant is present in a rear-facing infant seat • the system determines that a small child is present in a forward-facing child restraint •...
Page 86 The passenger sensing system is designed to enable (may inﬂate) the right front passenger’s frontal airbag anytime the system senses that a person of adult size is sitting properly in the right front passenger’s seat. When the passenger sensing system has allowed the airbag to be enabled, the on indicator will light and stay lit to remind you that the airbag is active.
Page 87 CAUTION: If the airbag readiness light in the instrument panel cluster ever comes on and stays on, it means that something may be wrong with the airbag system. If this ever happens, have the vehicle serviced promptly, because an adult-size person sitting in the right front passenger’s seat may not have the protection of the frontal airbag.
Page 88: Servicing Your Airbag-Equipped Vehicle
Servicing Your Airbag-Equipped Vehicle Airbags affect how your vehicle should be serviced. There are parts of the airbag system in several places around your vehicle. Your dealer and the service manual have information about servicing your vehicle and the airbag system. To purchase a service manual, see Service Publications Ordering Information on page 7-12.
Page 89: Restraint System Check
Restraint System Check Checking Your Restraint Systems Now and then, make sure the safety belt reminder light and all your belts, buckles, latch plates, retractors and anchorages are working properly. Look for any other loose or damaged safety belt system parts. If you see anything that might keep a safety belt system from doing its job, have it repaired.
Page 90 If the LATCH system was being used during a more severe crash, you may need new LATCH system parts. If belts are cut or damaged, replace them. Collision damage also may mean you will need to have LATCH system, safety belt or seat parts repaired or replaced. New parts and repairs may be necessary even if the belt or LATCH system was not being used at the time of the collision.
Page 91: Features And Controls
Section 2 Keys ...2-3 Remote Keyless Entry System ...2-5 Remote Keyless Entry System Operation ...2-6 Doors and Locks ...2-8 Door Locks ...2-8 Power Door Locks ...2-9 Delayed Locking ...2-9 Programmable Automatic Door Locks ...2-10 Rear Door Security Locks ...2-10 Lockout Protection ...2-11 Liftgate ...2-11 Windows ...2-13 Power Windows ...2-14...
Page 92 Section 2 Front Armrest Storage Area ...2-40 Rear Storage Area ...2-40 Roof Rack System ...2-40 Convenience Net ...2-43 Cargo Cover ...2-43 Rear Convenience Center ...2-44 Features and Controls Sunroof ...2-47 Vehicle Personalization ...2-47 Memory Seat ...2-47...
Page 93: Keys
Keys CAUTION: Leaving children in a vehicle with the ignition key is dangerous for many reasons. They could operate the power windows or other controls or even make the vehicle move. The children or others could be badly injured or even killed.
Page 94 Your vehicle’s key can be used for the ignition as well as the driver’s door lock, the ﬂoor console, and the glove box. If you need a new key, contact your dealer, who can obtain the correct key code. ® Your vehicle has the PASS-Key system.
Page 95: Remote Keyless Entry System
Remote Keyless Entry System If equipped, the keyless entry system operates on a radio frequency subject to Federal Communications Commission (FCC) Rules and with Industry Canada. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1.
Page 96: Remote Keyless Entry System Operation
Remote Keyless Entry System Operation With this feature, you can lock and unlock your doors from about 3 feet (1 m) up to 30 feet (9 m) away using the remote keyless entry transmitter supplied with your vehicle. UNLOCK: Press UNLOCK to unlock only the driver’s door.
Page 97: Battery Replacement
Matching Transmitter(s) to Your Vehicle Each remote keyless entry transmitter is coded to prevent another transmitter from unlocking your vehicle. If a transmitter is lost or stolen, a replacement can be purchased through your dealer. Remember to bring any remaining transmitters with you when you go to your dealer.
Page 98: Doors And Locks
Doors and Locks Door Locks CAUTION: Unlocked doors can be dangerous. • Passengers — especially children — can easily open the doors and fall out of a moving vehicle. When a door is locked, the handle will not open it. You increase the chance of being thrown out of the vehicle in a crash if the doors are not locked.
Page 99: Power Door Locks
Power Door Locks The power door lock switch is located on the driver’s and front passenger’s doors next to the door handle. Press the front of the switch to lock all doors, or press the back of the switch to unlock all doors. The rear doors do not have power door lock switches.
Page 100: Programmable Automatic Door Locks
Programmable Automatic Door Locks All of the doors will automatically lock when all doors are closed, the engine is running and the shift lever is shifted out of PARK (P). All of the doors will automatically unlock when the shift lever is shifted into PARK (P).
Page 101: Lockout Protection
Canceling the Rear Door Security Locks 1. Unlock and open the rear door from the outside. 2. Push the lever down to disengage the safety lock. 3. Close the door. 4. Repeat Steps 1 through 3 for the other rear door lock.
Page 102 Liftgate Release Liftgate Handle Your vehicle is equipped with a liftgate release touchpad, located on the inner side of the liftgate handle. 2-12 To open the liftgate using the touchpad, do the following: 1. Put the vehicle in PARK (P). 2.
Page 103: Windows
Windows CAUTION: Leaving children, helpless adults, or pets in a vehicle with the windows closed is dangerous. They can be overcome by the extreme heat and suffer permanent injuries or even death from heat stroke. Never leave a child, a helpless adult, or a pet alone in a vehicle, especially with the windows closed in warm or hot weather.
Page 104: Power Windows
Power Windows Switches on the driver’s door armrest control each of the windows when the ignition is in ON, ACCESSORY, or when Retained Accessory Power (RAP) is active. See Retained Accessory Power (RAP) on page 2-21 for more information. In addition, each passenger’s door has a window switch.
Page 105: Sun Visors
Window Lock Out The driver’s window controls also include a lock-out switch. Press the right side of the WDO LOCK switch to stop rear passengers from lowering their window. The driver can still control all of the windows with the lock on.
Page 106: Arming With The Power Lock Switch
Once armed, the alarm will go off if someone tries to enter the vehicle without using the optional remote keyless entry transmitter or the key, or tries to turn the ignition on without using the correct key. The horn will sound and the headlamps and parking lamps will ﬂash any time the alarm sounds.
Page 107: Disarming With Your Key
Disarming with Your Key Your alarm system will disarm when you use your key to unlock the driver’s door. The security light will stop ﬂashing to let you know the system is no longer armed. Disarming with the Remote Keyless Entry Transmitter Your alarm system will disarm when you press UNLOCK on your remote keyless entry transmitter to unlock the...
Page 108: Pass-Key ® Iii
® PASS-Key III Operation Your vehicle is equipped with the PASS-Key (Personalized Automotive Security System) theft-deterrent system. PASS-Key theft deterrent system. This means you don’t have to do anything different to arm or disarm the system. It works when you insert or remove the key from the ignition.
Page 109: Starting And Operating Your Vehicle
® To program the new PK3 key do the following: ® 1. Verify the new key has PK3 2. Insert the original key in the ignition and start the engine. If the engine will not start, see your dealer for service. 3.
Page 110: Ignition Positions
Ignition Positions With the key in the ignition, you can turn it to four different positions. A (OFF): This is the only position in which you can remove the key. This position locks the ignition and transaxle. Notice: Using a tool to force the key from the ignition switch could cause damage or break the key.
Page 111: Retained Accessory Power (Rap)
Retained Accessory Power (RAP) With RAP, the power windows, the audio system, the sunroof and the automatic level control will continue to work for up to 10 minutes after the ignition key is turned to OFF or until one of the doors is opened. Starting Your Engine Move your shift lever to PARK (P) or NEUTRAL (N).
Page 112: Engine Coolant Heater
Engine Coolant Heater Your vehicle may have an engine coolant heater. In very cold weather, 0°F ( 18°C) or colder, the engine coolant heater can help. You will get easier starting and better fuel economy during engine warm-up. Usually, the coolant heater should be plugged in a minimum of four hours prior to starting your vehicle.
Page 113: Automatic Transaxle Operation
Automatic Transaxle Operation Maximum engine speed is limited when you are in PARK (P) or NEUTRAL (N), to protect driveline components from improper operation. There are several different positions for your shift lever. PARK (P): This gear position locks your front wheels. It is the best position to use when you start your engine because your vehicle cannot move easily.
Page 114 REVERSE (R): Use this gear to back up. Notice: Shifting to REVERSE (R) while your vehicle is moving forward could damage the transaxle. The repairs would not be covered by your warranty. Shift to REVERSE (R) only after your vehicle is stopped.
Page 115 Warm-Up Shift Your vehicle has a computer controlled transaxle designed to warm up the engine faster when the outside temperature is 35°F (2°C) or colder. You may notice that the transaxle will shift at a higher vehicle speed until the engine is warmed up. This is a normal condition designed to provide heat to the passenger compartment and defrost the windows more quickly.
Page 116: All-Wheel Drive
All-Wheel Drive If your vehicle has all-wheel drive, your engine’s driving power is sent to all four wheels for extra traction when needed. This is like four-wheel drive, but there is no separate lever or switch to engage or disengage the front axle. It is fully automatic, and adjusts itself as needed for road conditions.
Page 117: Shifting Into Park (P)
Shifting Into Park (P) CAUTION: It can be dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the parking brake ﬁrmly set. Your vehicle can roll. If you have left the engine running, the vehicle can move suddenly.
Page 118: Shifting Out Of Park (P)
Torque Lock If you are parking on a hill and you do not shift your vehicle into PARK (P) properly, the weight of the vehicle may put too much force on the parking pawl in the transaxle. You may ﬁnd it difficult to pull the shift lever out of PARK (P).
Page 119: Parking Over Things That Burn
Parking Over Things That Burn CAUTION: Things that can burn could touch hot exhaust parts under your vehicle and ignite. Do not park over papers, leaves, dry grass or other things that can burn. Engine Exhaust CAUTION: Engine exhaust can kill. It contains the gas carbon monoxide (CO), which you cannot see or smell.
Page 120: Running Your Engine While You Are Parked
Running Your Engine While You Are Parked It is better not to park with the engine running. But if you ever have to, here are some things to know. CAUTION: Idling the engine with the climate control system off could allow dangerous exhaust into your vehicle.
Page 121: Mirrors
Mirrors Manual Rearview Mirror The vehicle may have a rearview mirror that can be adjusted for day or night driving. Push or pull the tab at the bottom of the mirror to adjust it for day or night conditions. The mirror’s two outer buttons operate the lamps on the bottom of the mirror.
Page 122: Outside Curb View Assist Mirror
Outside Curb View Assist Mirror If the vehicle has this feature, it can be helpful when parallel parking. The passenger’s outside rearview mirror will tilt towards the curb when the vehicle is shifted into REVERSE (R) and return to its previous position when the vehicle is shifted out of REVERSE (R).
Page 123: Onstar System
® OnStar System ® OnStar uses global positioning system (GPS) satellite technology, wireless communications, and call centers to provide you with a wide range of safety, security, information, and convenience services. ® A complete OnStar user’s guide and the terms and ®...
Page 124: Homelink Transmitter
® OnStar Personal Calling ® As an OnStar subscriber, the Personal Calling capability is available if your hand-held cell phone is lost, forgotten, or has a low battery. It is a hands-free wireless phone that is integrated into the vehicle. Calls can be placed nationwide using simple voice commands with no additional contracts and no additional roaming charges.
Page 125: Programming The Homelink
This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference received, including interference that may cause undesired operation of the device. Changes and modiﬁcations to this system by other than an authorized service facility could void authorization to use this equipment.
Page 126 Programming HomeLink Your vehicle’s engine should be turned off while programming the transmitter. Follow these steps to program up to three channels: 1. Press and hold down the two outside buttons, releasing only when the indicator light begins to ﬂash, after 20 seconds. Do not hold down the buttons for longer than 30 seconds and do not repeat this step to program a second and/or third transmitter to the remaining two HomeLink...
Page 127: Using Homelink
8. Return to the vehicle. Firmly press and hold the ® programmed HomeLink button for two seconds, then release. Repeat the press/hold/release sequence a second time, and depending on the brand of the garage door opener (or other rolling code device), repeat this sequence a third time to complete the programming.
Page 128: Storage Areas
® Erasing HomeLink Buttons To erase programming from the three buttons do the following: 1. Press and hold down the two outside buttons until the indicator light begins to ﬂash, after 20 seconds. Do not hold the two outside buttons for longer than 30 seconds.
Page 129: Cupholder(S)
Cupholder(s) There are two cupholders located in the ﬂoor console. The cupholders have liners that remove for larger beverage items. Remove the liners by lifting them out. Your vehicle has cupholders located in the rear seat armrests if it has a split folding rear seat. If your vehicle has captain’s chairs, there are cupholders on the sides of the seats.
Page 130: Front Armrest Storage Area
Front Armrest Storage Area Your vehicle has a front armrest storage compartment which contains two storage compartments. To unlock the front armrest storage compartment, put your key into the lock and turn the key counterclockwise. To open the armrest, squeeze the lever while lifting the top to open it.
Page 131 If you have the luggage carrier with crossrails you can load things on top of your vehicle. If you do load things on the top of your vehicle, you must load them on the luggage carrier crossrails. Some vehicles may not have the crossrails.
Page 132 Don’t exceed the maximum vehicle capacity when loading your vehicle. For more information on vehicle capacity and loading, see Loading Your Vehicle on page 4-31. To prevent damage or loss of cargo as you’re driving, check now and then to make sure the luggage carrier and cargo are still securely fastened.
Page 133: Convenience Net
To adjust the crossrails, lift the release levers on each side to unlock them. Slide the crossrails forward or backward, as needed, to accommodate loads of various sizes. After repositioning the crossrails, push the release lever down. This will lock the crossrails in place. Notice: Opening the sunroof when the luggage rack crossrails are not in the full-rear position could cause damage to the sunroof or luggage rack.
Page 134: Rear Convenience Center
Rear Convenience Center CAUTION: If any removable convenience item is not secured properly, it can move around in a collision or sudden stop. People in the vehicle could be injured. Be sure to secure any such item properly. Your vehicle may have a rear convenience center. The rear convenience center can be used to organize and store items in your vehicle.
Page 135 Reinstalling the Extended Rear Convenience Center 1. Make sure that all items have been removed from the rear of the vehicle. 2. Remove the carpeted mat from the vehicle. 3. Lift the forward bin into the back of the vehicle. Place the mounting brackets onto the forward mounting bolts on the ﬂoor of the vehicle.
Page 136 Removing the Rear Convenience Center on Vehicles with the Third Row Stowable Seat 1. Make sure that all items have been removed from the top and the inside of the rear convenience center. 2. Lift the handle(s) on the top of the lid to open the storage bin.
Page 137: Sunroof
Sunroof If the vehicle has a sunroof, the switch to operate it is located on the headliner, between the sun visors. The sunroof switch will only work when the ignition is ON or when the ignition is OFF and retained accessory power (RAP) is active.
Page 138 To store the memory settings, do the following: 1. Adjust the driver’s seat and the outside rearview mirrors to the position you would like for driving. 2. Press and hold memory button 1 for more than three seconds. A double beep will sound when the memory seat and mirror position have been stored.
Page 139: Instrument Panel
Section 3 Instrument Panel Overview ...3-4 Hazard Warning Flashers ...3-6 Other Warning Devices ...3-6 Horn ...3-6 Tilt Wheel ...3-6 Turn Signal/Multifunction Lever ...3-7 Turn and Lane-Change Signals ...3-7 Headlamp High/Low-Beam Changer ...3-8 Flash-to-Pass ...3-8 Windshield Wipers ...3-9 Windshield Washer ...3-9 Cruise Control ...3-10 Exterior Lamps ...3-14 Daytime Running Lamps (DRL) ...3-14...
Page 140 Section 3 Message Center ...3-51 Passenger Seatbelt Reminder Message ...3-51 Service Traction System Warning Message ...3-51 Traction Active Message ...3-52 Engine Coolant Temperature Warning Message ...3-52 Charging System Indicator Message ...3-53 Reduced Engine Power Message ...3-53 Low Oil Pressure Message ...3-54 Low Engine Oil Level Message ...3-55 Change Engine Oil Message ...3-55 Low Tire Message ...3-56...
Page 141 NOTES...
Page 142: Instrument Panel Overview
Instrument Panel Overview...
Page 143 The main components of the instrument panel are the following: A. Exterior/Interior Lamps Control. See Exterior Lamps on page 3-14 and Interior Lamps on page 3-16. B. Turn Signal/Multifunction Lever. See Turn Signal/Multifunction Lever on page 3-7. C. Hazard Warning Flasher Button. See Hazard Warning Flashers on page 3-6.
Page 144: Hazard Warning Flashers
Hazard Warning Flashers Your hazard warning ﬂashers let you warn others. They also let police know you have a problem. Your front and rear turn signal lamps will ﬂash on and off. The hazard warning ﬂasher button is located on top of the steering column.
Page 145: Turn Signal/Multifunction Lever
Turn Signal/Multifunction Lever The lever on the left side of the steering column includes the following: • Turn and Lane-Change Signals. See Turn and Lane-Change Signals on page 3-7. • Headlamp High/Low-Beam Changer. See Headlamp High/Low-Beam Changer on page 3-8. •...
Page 146: Headlamp High/Low-Beam Changer
As you signal a turn or a lane change, if the arrow ﬂashes faster than normal, a signal bulb may be burned out and other drivers will not see your turn signal. If a bulb is burned out, replace it to help avoid an accident.
Page 147: Windshield Wipers
Windshield Wipers WIPER : Turn the band marked WIPER to control the windshield wipers. MIST: For a single wiping cycle, turn the band to MIST. Hold it there until the wipers start, then let go. The wipers will stop after one cycle. If you want more cycles, hold the band on MIST longer.
Page 148: Cruise Control
Rear Window Washer/Wiper The rear window washer/wiper switch is located in the instrument panel switchbank. See Instrument Panel Switchbank on page 3-20. (Rear Intermittent Wiper) Press the wiper symbol on the top of the switch to turn on the intermittent wiper. To turn off the wiper, gently press the bottom of the switch.
Page 149 The cruise controls are located on the end of the turn signal/multifunction lever. ON: Move the switch to this position to turn the cruise control system on. R/A: Move the switch to this position to resume a set speed or to accelerate. SET: Press this button, located at the end of the lever, to set a speed.
Page 150 Setting Cruise Control CAUTION: If you leave your cruise control on when you are not using cruise, you might hit a button and go into cruise when you do not want to. You could be startled and even lose control. Keep the cruise control switch off until you want to use cruise control.
Page 151 • Move the cruise switch from ON to R/A. Hold it there until you get up to the speed you want, and then release the switch. To increase your speed in very small amounts, move the switch to R/A brieﬂy and then release it. Each time you do this, your vehicle will go about 1 mph (1.6 km/h) faster.
Page 152: Exterior Lamps
Exterior Lamps The control on the left side of the steering column operates the exterior lamps. The exterior lamp control has three positions: AUTO (Automatic Headlamp Control/Off): Turning the control to this position will activate the automatic headlamps when it is dark enough outside and turn off all lamps and lights during the day except for the Daytime Running Lamps (DRL).
Page 153: Automatic Headlamp System
When the DRL are on, only your reduced intensity high-beam headlamps will be on. Your instrument panel will not be lit up. When it is dark enough outside, the exterior lamps will come on automatically. When it is bright enough outside, the exterior lamps will go out and the DRL will turn on.
Page 154: Interior Lamps
Interior Lamps The interior lamps can be controlled, or automatically turn on or off under certain conditions. They are explained in the following text. Instrument Panel Brightness This feature controls the brightness of the instrument panel lights. The knob for this feature is located on the interior lamps control.
Page 155: Headlamp Exit Delay
Headlamp Exit Delay If your vehicle has headlamp exit delay, it will keep the headlamps and parking lamps on at night for 30 seconds if the following conditions are met: • The ignition is turned to OFF. • The exterior lamp control is in the AUTO position. •...
Page 156: Delayed Lighting
Delayed Lighting If your vehicle has delayed lighting, it will continue to illuminate the interior for 25 seconds after all doors have been closed. The lamps will continue to illuminate when the following conditions are met: • A door is opened then closed. •...
Page 157: Perimeter Lighting
Perimeter Lighting If your vehicle has perimeter lighting, it will turn on the headlamps and parking lamps for 25 seconds when the following conditions are met: • The ignition is turned to OFF. • The exterior lamp control is in the AUTO position. •...
Page 158: Battery Run-Down Protection
Battery Run-Down Protection Your vehicle has a feature to help prevent you from draining the battery, in case you accidentally leave the interior or exterior lamps on. If the interior lamps are left on while the ignition is in OFF, they will automatically turn off after 10 minutes.
Page 159: Head-Up Display (Hud)
Head-Up Display (HUD) CAUTION: If the HUD image is too bright, or too high in your ﬁeld of view, it may take you more time to see things you need to see when it is dark outside. Be sure to keep the HUD image dim and placed low in your ﬁeld of view.
Page 160 Under warning conditions, the CHECK GAGES message will illuminate in the HUD. Look at the instrument panel cluster for more information. Notice: If you try to use the HUD image as a parking aid, you may misjudge the distance and damage your vehicle.
Page 161 HUD image harder to see. When you ﬁrst start the vehicle the display will show BUICK and the Buick logo for a few seconds. If it is cold outside, this display may stay on for up to a minute. Clean the inside of the windshield as needed to remove any dirt or ﬁlm that reduces the sharpness or clarity...
Page 162: Ultrasonic Rear Parking Assist (Urpa)
Ultrasonic Rear Parking Assist (URPA) The Ultrasonic Rear Parking Assist (URPA) system is designed to help you park, while the vehicle is in REVERSE (R). It operates only at very low speeds, less than 3 mph (5 km/h). URPA can help make parking easier and to help you avoid colliding with objects such as parked vehicles.
Page 163: How The System Works
URPA can be turned off by pressing the rear park aid disable switch located in the instrument panel switchbank. When the system is disabled, an indicator light will glow on the switch. You will not see any lights on the rear display if the switch is in the off position.
Page 164: Accessory Power Outlets
When the System Does Not Seem to Work Properly The light may ﬂash red when the vehicle is in REVERSE (R) if the ultrasonic sensors are not kept clean. So be sure to keep your rear bumper free of mud, dirt, snow, ice, and slush.
Page 165: Ashtrays And Cigarette Lighter
Certain electrical accessories may not be compatible with the accessory power outlet and could result in blown vehicle or adapter fuses. If you experience a problem, see your dealer for additional information on the accessory power outlets. Notice: Adding any electrical equipment to your vehicle may damage it or keep other components from working as they should.
Page 166: Climate Controls
Climate Controls Climate Control System With this system you can control the heating, cooling, and ventilation for your vehicle. Operation Turn the right knob clockwise or counterclockwise to direct the airﬂow inside your vehicle. To change the current mode, select one of the following: (Vent): This mode directs air to the instrument panel outlets.
Page 167: Defogging And Defrosting
Temperature Control: Turn the center knob clockwise or counterclockwise to increase or decrease the air temperature inside your vehicle. A/C (Air Conditioning): Press this button to turn the air-conditioning system on or off. When A/C is pressed, an indicator light in the button will come on to let you know that air conditioning is activated.
Page 168: Dual Climate Control System
Rear Window Defogger The rear window defogger uses a warming grid to remove fog from the rear window. < REAR: Press this button to turn the rear window defogger on or off. An indicator light in the button will come on to let you know that the rear window defogger is activated.
Page 169 (Floor): This mode directs most of the air to the ﬂoor outlets. Use this mode to send air to the rear of the vehicle. Keep the area under the front seats free of objects that could obstruct airﬂow to the rear of the vehicle.
Page 170: Rear Window Defogger
Defogging and Defrosting Fog on the inside of windows is a result of high humidity, or moisture, condensing on the cool window glass. This can be minimized if the climate controls system is used properly. There are two modes to clear fog or frost from your windshield.
Page 171: Dual Automatic Climate Control System
Dual Automatic Climate Control System Your vehicle may have the dual automatic climate control system. With this system you can control the heating, cooling, and ventilation for your vehicle. Automatic Operation AUTO (Automatic): When the driver’s temperature knob is pressed to select AUTO and the temperature is set, the system will automatically control the inside temperature, the air delivery and the fan speed.
Page 172 Manual Operation MODE: Press this button to manually change the direction of airﬂow in your vehicle; keep pressing the button until the desired mode appears on the display. To change the current mode, select one of the following: (Vent): This mode directs air to the instrument panel outlets.
Page 173 Air Conditioning: The air-conditioning compressor will automatically come on when a temperature cooler than the interior temperature is chosen using the temperature knobs. You may notice a slight change in engine performance when the air-conditioning compressor shuts off and turns on again. This is normal. The system is designed to make adjustments to help with fuel economy while still maintaining the selected temperature.
Page 174: Outlet Adjustment
Rear Window Defogger The rear window defogger uses a warming grid to remove fog from the rear window. < REAR: Press this button to turn the rear window defogger on or off. An indicator light in the button will come on to let you know that the rear window defogger is activated.
Page 175: Warning Lights, Gages, And Indicators
Warning Lights, Gages, and Indicators This part describes the warning lights and gages that may be on your vehicle. The pictures will help you locate them. Warning lights and gages can signal that something is wrong before it becomes serious enough to cause an expensive repair or replacement.
Page 176: Instrument Panel Cluster
Instrument Panel Cluster Your instrument panel cluster is designed to let you know at a glance how your vehicle is running. You’ll know how fast you’re going, how much fuel you’re using, and many other things you’ll need to drive safely and economically. The indicator warning lights and gages are explained on the following pages.
Page 177: Speedometer And Odometer
Speedometer and Odometer Your speedometer lets you see your speed in both miles per hour (mph) and kilometers per hour (km/h). Your odometer shows how far your vehicle has been driven, in either miles (used in the United States) or kilometers (used in Canada). However, a Canadian odometer will remain in metric units only.
Page 178: Tachometer
Retro-Active Reset The trip odometer has a feature called retro-active reset. This feature can be used to set the trip odometer to the number of miles or kilometers driven since the ignition was last turned on. This can be used if you forget to reset your trip odometer at the beginning of a trip.
Page 179: Safety Belt Reminder Light
Safety Belt Reminder Light When the key is turned to ON or START, a chime will come on for several seconds to remind people to fasten their safety belts. The safety belt light will also come on and stay on for several seconds.
Page 180: Passenger Airbag Status Indicator
If the airbag readiness light stays on after you start the vehicle or comes on when you are driving, your airbag system or safety belt pretensioners may not work properly. Have your vehicle serviced right away. CAUTION: If the airbag readiness light stays on after you start your vehicle, it means the airbag system may not be working properly.
Page 181 CAUTION: If the on indicator comes on when you have a rear-facing child restraint installed in the right front passenger’s seat, it means that the passenger sensing system has not turned off the passenger’s frontal airbag. A child in a rear-facing child restraint can be seriously injured or killed if the right front passenger’s airbag inﬂates.
Page 182: Brake System Warning Light
Brake System Warning Light When the ignition is on, the brake system warning light will come on when you set your parking brake. The light will stay on if your parking brake doesn’t release fully. If it stays on after your parking brake is fully released, it means you have a brake problem.
Page 183: Anti-Lock Brake System Warning Light
Anti-Lock Brake System Warning Light United States Your vehicle may have an anti-lock brake system warning light. If it does, the light should come on for a few seconds when you turn the ignition key to ON. If the anti-lock brake system warning light stays on longer than normal after you’ve started your engine, turn the ignition off.
Page 184: Engine Coolant Temperature Gage
Engine Coolant Temperature Gage United States This gage shows the engine coolant temperature. If the gage pointer moves into the red area, your engine is too hot! It means that your engine coolant has overheated. If you have been operating your vehicle under normal driving conditions, you should pull off the road, stop your vehicle and turn off the engine as soon as possible.
Page 185: If The Light Is Flashing
Notice: If you keep driving your vehicle with this light on, after awhile, your emission controls may not work as well, your fuel economy may not be as good, and your engine may not run as smoothly. This could lead to costly repairs that may not be covered by your warranty.
Page 186: If The Light Is On Steady
If the Light Is On Steady You may be able to correct the emission system malfunction by considering the following: Did you recently put fuel into your vehicle? If so, reinstall the fuel cap, making sure to fully install the cap. See Filling Your Tank on page 5-8. The diagnostic system can determine if the fuel cap has been left off or improperly installed.
Page 187 Emissions Inspection and Maintenance Programs Some state/provincial and local governments have or may begin programs to inspect the emission control equipment on your vehicle. Failure to pass this inspection could prevent you from getting a vehicle registration. Here are some things you need to know in order to help your vehicle pass an inspection: Your vehicle will not pass this inspection if the SERVICE ENGINE SOON or check engine light is on or not...
Page 188: Fuel Gage
Fuel Gage United States When the indicator nears empty, you still have a little fuel left, but you should get more soon. If your fuel is low, the warning message in the message center will come on. See Low Fuel Warning Message on page 3-58.
Page 189: Message Center
Message Center The message center is located at the top of the instrument panel cluster in between the tachometer and speedometer. It gives you important safety and maintenance facts. Passenger Seatbelt Reminder Message If your vehicle is equipped with the passenger sensing system, this message reminds the passenger to buckle their...
Page 190: Traction Active Message
Traction Active Message United States If your vehicle has the traction control system, the TRACTION ACTIVE message will appear when the traction control system is limiting wheel spin. You may feel or hear the system working, but this is normal. Slippery road conditions may exist if this message appears, so adjust your driving accordingly.
Page 191: Charging System Indicator Message
Charging System Indicator Message The charging system battery symbol will come on in the message center when you turn on the ignition as a check to show you it is working. It will remain on as long as the engine is not running. It should go out once the engine is running.
Page 192: Low Oil Pressure Message
Low Oil Pressure Message United States Your vehicle is equipped with a low oil pressure warning message. Your oil pressure message lets you know when you may have a problem with your engine oil pressure. When the engine is running and this message appears, the engine oil level may be too low.
Page 193: Low Engine Oil Level Message
Low Engine Oil Level Message United States Your vehicle may have a low engine oil level message. If this message comes on, it means your engine is low on oil. You should check your oil level right away. Have your vehicle serviced immediately. See Engine Oil on page 5-16 for more information.
Page 194: Low Tire Message
Low Tire Message United States Your vehicle may have the check tire pressure system which can alert you to a large change in the pressure of one tire. After the system has been properly calibrated, the low tire pressure message will come on and a chime will sound if a pressure difference, or low pressure, is detected in one tire.
Page 195: Check Gas Cap Message
Check Gas Cap Message If your vehicle is equipped, this message will come on when the ignition is turned to on or start and the gas cap is open. ® PASS-Key III Security Message United States If you are ever driving and this message comes on and stays on, you will be able to restart your engine if you turn it off.
Page 196: Low Washer Fluid Warning Message
Low Washer Fluid Warning Message United States Your vehicle may have a low washer ﬂuid warning message. If your washer ﬂuid is low, this warning message will come on and stay on until you add washer ﬂuid. See Windshield Washer Fluid on page 5-37 for adding washer ﬂuid instructions.
Page 197: Low Brake Fluid Warning Message
Low Brake Fluid Warning Message United States If your brake ﬂuid is low, the warning message will come on and stay on until you add brake ﬂuid. The brake system warning light will also be illuminated. If this message appears, the brakes need attention. You should have your vehicle serviced immediately.
Page 198: Program Mode Message
Program Mode Message United States If you receive this message, your vehicle is in program mode. If your vehicle is equipped with the Driver Information Center (DIC), you are ready to begin programming your vehicle’s customization features. See DIC Vehicle Personalization on page 3-66 for more information.
Page 199: Parking Lamp Warning Message
Parking Lamp Warning Message United States If you receive this message, one or both of the vehicle’s parking lamp bulbs needs replacement. See Bulb Replacement on page 5-49 for bulb replacement instructions. Highbeam Out Warning Message Canada United States If you receive this message, one or both of the vehicle’s high-beam headlamp bulbs needs replacement.
Page 200: Driver Information Center (Dic)
Driver Information Center (DIC) United States shown, Canada similar If your vehicle is equipped with the Driver Information Center (DIC), the display is located on the instrument panel cluster in the tachometer gage. The DIC will show information about the vehicle and the surroundings. The DIC is capable of displaying English or French.
Page 201 ZONE - - PRESS & HOLD SET TO CHANGE: This display mode will appear when you are manually calibrating the system. When the compass is being recalibrated for the ﬁrst time, the zone symbol will be displayed. When the compass is being recalibrated any time after that, the current zone number for compass variance will be displayed in place of the zone symbol.
Page 202: Dic Controls And Displays
When the ignition is turned to ON or START, the DIC will display the following: BUICK: BUICK will be displayed for three seconds. DRIVER #: This message will be displayed for another three seconds after BUICK appears in the display.
Page 203 FUEL USED: The fuel used display will show you how much fuel has been used since the last time it was reset. To reset the fuel used to zero, press and hold the SET button while the fuel used is displayed on the DIC and until the display goes to zero.
Page 204: Dic Vehicle Personalization
DIC Vehicle Personalization The DIC is used to program the choices of two drivers. The drivers are recognized as DRIVER 1 or DRIVER 2 in the DIC display. You will let the DIC know which driver you are by using your remote keyless entry transmitter. Each remote keyless entry transmitter was pre-programmed to belong to DRIVER 1 or DRIVER 2.
Page 205 United States 4. The program mode message will appear in the message center as an indication that your vehicle is ready to begin programming. 5. Follow the instructions given by the DIC. Headlamp Exit Delay This feature allows you to customize the headlamps and parking lamps.
Page 206: Interior Lighting Delay
Interior Lighting Delay The interior lighting delay feature can be programmed to one of the following modes: OFF: This feature will not illuminate the interior of your vehicle when all of the doors are closed. ON: This feature will continue to illuminate the interior lamps for 25 seconds after all doors have been closed so that you can ﬁnd your ignition and buckle your safety belt at night.
Page 207 Interior lighting on will not occur while the ignition is in ON. After 25 seconds, the interior lamps will fade out. The lamps will fade out before the 25 seconds if one of the following occurs: • The ignition is turned to ON •...
Page 208 If the auto door unlock feature has been programmed to DRIVER or ALL, the automatic door unlock feature can also be programmed to one of the following modes: PARK: Unlock when the shift lever is put in PARK (P). KEY OUT: Unlock when the ignition key is removed. Your vehicle was originally programmed to PARK.
Page 209: Remote Door Unlock
Your vehicle was originally programmed to ON. The mode may have been changed since then. To determine the current mode, or to change the mode, do the following: 1. Follow the instructions for “Entering Programming Mode” listed previously. 2. Press the MODE button until DELAYED LOCKING appears on the DIC.
Page 210: Unlock Feedback
Unlock Feedback The unlock feedback feature can be programmed to one of the following modes: LIGHTS: This mode does the following: • During the day, when the ignition is in OFF and UNLOCK on the remote keyless entry transmitter is pressed, the headlamps and parking lamps will ﬂash.
Page 211 Lock Feedback The lock feedback feature can be programmed to one of the following modes: OFF: When LOCK is pressed on the remote keyless entry transmitter, the headlamps and parking lamps will not ﬂash and the horn will not sound. LIGHTS: When LOCK is pressed on the remote keyless entry transmitter, the headlamps and parking lamps will ﬂash brieﬂy.
Page 212: Tilt Mirror
If the seat recall feature has been programmed to ON, the seat recall feature can also be programmed to one of the following modes: MEMORY: The position recalled will be the memory driving position. EXIT: The position recalled will be the previously programmed exit position.
Page 213: Audio System(S)
Exiting Programming Mode To exit programming mode, do one of the following: • Shift out of PARK (P). • Turn the ignition key out of ON. • Do not program any commands for one minute while in the programming mode. The programming mode message will turn off to let you know that you are no longer in the programming mode.
Page 214: Setting The Time
Setting the Time Press and hold H until the correct hour appears on the display. AM will appear for morning hours. Press and hold M until the correct minute appears on the display. The time can be set with the ignition on or off. To synchronize the time with an FM station broadcasting Radio Data System (RDS) information, press and hold H and M at the same time until TIME UPDATED...
Page 215: Playing The Radio
This system relies upon receiving speciﬁc information from these stations and will only work when the information is available. In rare cases, a radio station may broadcast incorrect information that will cause the radio features to work improperly. If this happens, contact the radio station.
Page 216: Finding A Station
DISP (Display): Press this button to switch the display between the radio station frequency and the time. Press this button to display the time when the ignition is turned off. For RDS, press the DISP button to change what appears on the display while using RDS. The display options are station, RDS station frequency, PTY, and the name of the program (if available).
Page 217: Setting Preset Stations
Setting Preset Stations Up to 30 stations (six FM1, six FM2, and six AM, six XM1 and six XM2 (if equipped), can be programmed on the six numbered pushbuttons, by performing the following steps: 1. Turn the radio on. 2. Press BAND to select FM1, FM2, or AM, or XM1 or XM2.
Page 218: Rds And Xm
Adjusting the Speakers (Balance/Fade) AUDIO: To adjust the balance between the right and the left speakers, push and release the AUDIO knob until BAL appears on the display. Then turn the AUDIO knob to move the sound toward the right or the left speakers.
Page 219: Rds Messages
SCAN: Scan the stations within a PTY by performing the following: 1. Press P-TYP to activate program type select mode. The PTY symbol will appear on the display. 2. Turn the AUDIO knob to select a PTY. 3. Once the desired PTY is displayed, press and hold either SEEK arrow, and the radio will begin scanning the stations in the PTY.
Page 220: Radio Messages
TRAF (Traffic): If TRAF appears on the display, the tuned station broadcasts traffic announcements. Press this button to receive the traffic announcement from the station and brackets will be displayed around TRAF. When a traffic announcement comes on the tuned radio station you will hear it. If the station does not broadcast traffic announcements, press the TRAF button and the radio will seek to a station that does.
Page 221 Radio Display Message XL (Explicit Language XL on the radio display, Channels) after the channel name, indicates content with explicit language. Updating Updating encryption code No Signal Loss of signal Loading XM Acquiring channel audio (after 4 second delay) CH Off Air Channel not in service CH Unavail Channel no longer...
Page 222 Radio Display Message No Info Song/Program Title not available No Info Category Name not available No Info No Text/Informational message available Not Found No channel available for the chosen category XM Locked Theft lock active Radio ID Radio ID label (channel 0) Unknown Radio ID not known...
Page 223: Playing A Cd
Playing a CD Insert a CD partway into the slot, label side up. The player will pull it in and the CD should begin playing. If you want to insert a CD while the ignition or the radio is off, ﬁrst press the eject or DISP button. When a CD is inserted, the CD symbol will appear on the display.
Page 224 To scan tracks, press and hold either SEEK arrow for two seconds until SCAN appears on the display and you will hear a beep. The CD will go to the next track, play for a few seconds, then go on to the next track. The sound will mute and SCAN and the track number will appear on the display while scanning.
Page 225: Radio With Cassette And Cd
Listening to a DVD Your vehicle may have a Rear Seat Entertainment System, see Rear Seat Entertainment System on page 3-115 for more information. If your vehicle has this system and a DVD is playing, the DVD symbol will appear on the radio display indicating that the DVD is available and can be listened to through your vehicles speakers.
Page 226 This system relies upon receiving speciﬁc information from these stations and will only work when the information is available. In rare cases, a radio station may broadcast incorrect information that will cause the radio features to work improperly. If this happens, contact the radio station.
Page 227 SCV (Speed-Compensated Volume): With SCV, the audio system adjusts automatically to make up for road and wind noise as you drive. To use SCV, press the TUNE/AUDIO knob repeatedly until SPEED VOL appears on the display. Turn the TUNE/AUDIO knob to select MIN, MED, or MAX. Each higher setting will provide more volume compensation at faster vehicle speeds.
Page 228 Setting Preset Stations Up to 30 stations (six FM1, six FM2, and six AM, six XM1 and six XM2 (if equipped), can be programmed on the six numbered pushbuttons, by performing the following steps: 1. Turn the radio on. 2. Press BAND to select FM1, FM2, AM, or XM1, or XM2.
Page 229 Adjusting the Speakers (Balance/Fade) AUDIO: To adjust the balance between the right and the left speakers, push and release AUDIO until BAL appears on the display. Then turn the AUDIO knob to move the sound toward the right or the left speakers. A bar graph with indicators will appear on the display.
Page 230 SCAN: Scan the stations within a PTY by performing the following: 1. Press P-TYP to activate program type select mode. P-TYPE will appear on the display. 2. Turn the AUDIO knob to select a PTY. 3. Once the desired PTY is displayed, press and hold either SEEK arrow, and the radio will begin scanning the stations in the PTY.
Page 231 TRAF (Traffic): If TRAF appears on the display, the tuned station broadcasts traffic announcements. To receive the traffic announcement from the tuned station, press this button. Brackets will be displayed around TRAF and when a traffic announcement comes on the tuned radio station you will hear it. If the station does not broadcast traffic announcements, press this button and the radio will seek to a station that does.
Page 232 Radio Display Message XL (Explicit Language XL on the radio display, Channels) after the channel name, indicates content with explicit language. Updating Updating encryption code No Signal Loss of signal Loading XM Acquiring channel audio (after 4 second delay) CH Off Air Channel not in service CH Unavail Channel no longer...
Page 233 Radio Display Message No Info Category Name not available No Info No Text/Informational message available Not Found No channel available for the chosen category XM Locked Theft lock active Radio ID Radio ID label (channel 0) Unknown Radio ID not known (should only be if hardware failure) Chk XMRcvr...
Page 234: Playing A Cassette Tape
Playing a Cassette Tape The tape player is built to work best with tapes that are up to 30 to 45 minutes long on each side. Tapes longer than that are so thin they may not work well in this player. The longer side with the tape visible should face to the right.
Page 235: Cd Adapter Kits
BAND: Press this button to listen to the radio when a cassette tape or CD is playing. The inactive tape or CD will remain safely inside the radio for future listening. CD TAPE: Press this button to play a cassette tape or a CD when listening to the radio.
Page 236 Playing a CD Insert a CD partway into the slot, label side up. The player will pull it in and the CD should begin playing. If you want to insert a CD when the ignition or the radio is off, ﬁrst press the eject or the DISP button. If the ignition or radio is turned off with the CD in the player, it will stay in the player.
Page 237 © ¨ SEEK : Press the left arrow to go to the start of the current track if more than eight seconds have played. If either arrow is held or pressed more than once, the player will continue moving backward through the CD. Press the right arrow to go to the next track.
Page 238: Radio With Six-Disc Cd
Listening to a DVD Your vehicle may have a Rear Seat Entertainment System, see Rear Seat Entertainment System on page 3-115 for more information. If your vehicle has this system and a DVD is playing, the DVD symbol will appear on the radio display indicating that the DVD is available and can be listened to through your vehicles speakers.
Page 239 This system relies upon receiving speciﬁc information from these stations and will only work when the information is available. In rare cases, a radio station may broadcast incorrect information that will cause the radio features to work improperly. If this happens, contact the radio station.
Page 240 RCL (Recall): Press this knob to switch the display between the radio station frequency and the time. When the ignition is off, press this knob to display the time. For RDS, press the RCL knob to change what appears on the display while using RDS. The display options are station name, RDS station frequency, PTY, and the name of the program (if available).
Page 241 Setting Preset Stations Up to 30 stations (six FM1, six FM2, and six AM, six XM1 and six XM2 (if equipped)), can be programmed on the six numbered pushbuttons, by performing the following steps: 1. Turn the radio on. 2. Press BAND to select FM1, FM2, AM, or XM1 or XM2.
Page 242 Adjusting the Speakers (Balance/Fade) AUDIO: To adjust the balance between the right and the left speakers, push the AUDIO knob until BAL appears on the display. Turn the knob to move the sound toward the right or the left speakers. To adjust the fade between the front and rear speakers, push and hold the AUDIO knob until FAD appears on the display.
Page 243 To use the PTY interrupt feature, press and hold the P-TYPE button until you hear a beep on the PTY you want to interrupt with. When selected, an asterisk will appear beside that PTY on the display. You may select multiple interrupts if desired. When you are listening to a CD, the last selected RDS station will interrupt play if that selected program type format is broadcast.
Page 244 3. Turn the P-TYPE knob to select a PTY. 4. Press and hold one of the six numbered pushbuttons until you hear a beep. Whenever that numbered pushbutton is pressed, the PTY that was set will return. 5. Repeat the steps for each pushbutton. RDS Messages ALERT!: Alert warns of local or national emergencies.
Page 245 If the current tuned station does not broadcast traffic announcements, press the TRAF button and the radio will seek to a station that does. When a station that broadcasts traffic announcements is found, the radio will stop seeking and brackets will be displayed around TRAF.
Page 246 Radio Display Message XL (Explicit Language XL on the radio display, Channels) after the channel name, indicates content with explicit language. Updating Updating encryption code No Signal Loss of signal Loading XM Acquiring channel audio (after 4 second delay) CH Off Air Channel not in service CH Unavail Channel no longer...
Page 247 Radio Display Message No Info Song/Program Title not available No Info Category Name not available No Info No Text/Informational message available Not Found No channel available for the chosen category XM Locked Theft lock active Radio ID Radio ID label (channel 0) Unknown Radio ID not known...
Page 248 Playing a CD If the ignition or radio is turned off, with a CD in the player, it will stay in the player. When the ignition or radio is turned on, the CD will start playing where it stopped, if it was the last selected audio source. When a CD is inserted, the CD symbol will appear on the CD.
Page 249 To load more than one CD but less than six, complete Steps 1 through 3. When ﬁnished loading CDs, the radio will begin to play the last CD loaded. If more than one CD has been loaded, a number for each CD will be displayed.
Page 250 RPT (Repeat): With repeat, one track or an entire CD can be repeated. To use repeat, do the following: • To repeat the track you are listening to, press and release the RPT button. RPT will appear on the display. Press RPT again to turn off repeat play. •...
Page 251: Using Song List Mode
RCL (Recall): Press this knob to see how long the current track has been playing. To change the default on the display, track and elapsed time, press the knob until you see the display you want, then hold the knob until the display ﬂashes. The selected display will now be the default.
Page 252 To delete tracks from the song list, perform the following steps: 1. Turn the CD player on. 2. Press the SONG LIST button to turn song list on. S-LIST will appear on the display. 3. Press the SEEK SCAN arrows to select the desired track to be deleted.
Page 253: Rear Seat Entertainment System
If the CD is not playing correctly, for any other reason, try a known good CD. If any error occurs repeatedly or if an error cannot be corrected, contact your dealer. If the radio displays an error message, write it down and provide it to your dealer when reporting the problem.
Page 254: Before You Drive
Before You Drive The RSE is designed for rear seat passengers only. The driver cannot safely view the video screen while driving and should not try to do so. The DVD system is designed to be inoperable when the vehicle is exposed to extremely low or high temperatures, in order to protect the system from damage.
Page 255: Stereo Rca Jacks
Notice: Do not store the headphones in heat or direct sunlight. This could damage the headphones and repairs would not be covered by your warranty. Keep the headphones stored in a cool, dry place. If there is a decreased audio signal during CD or DVD play, there may be a low hissing noise through the speakers and/or headphones.
Page 256 Audio Output Audio from the DVD player or auxiliary devices can be heard through the following possible sources: • Wireless Headphones • Vehicle’s Speakers • Rear Seat Audio (RSA) RCA Jacks (if equipped). Plug the wired headphones (not included) into the jacks on the RSA system.
Page 257: Dvd Player
Video Screen The video screen is located in the overhead console. To use the video screen, do the following: 1. Push forward on the release button and the screen will fold down. 2. Push the screen away from you and adjust its position as desired.
Page 258 DVD Player Buttons (Eject): Press this button to eject a DVD or CD. (Power): Press this button to turn the DVD player on and off. SRCE (Source): Press this button to switch the system between the DVD player and an auxiliary source. (Stop): Press this button to stop playing, rewinding, or fast forwarding.
Page 259: Playing A Disc
(Directional Control Circle): Press these buttons to move through menu choices, or to move forward or back in a movie. These controls can be used to move forward or backward through a CD. (Enter): Press this button to select choices highlighted in any menu.
Page 260: Remote Control
Remote Control To use the remote control, aim it at the transmitter window below the video screen and press the desired button. Direct sunlight or very bright light may affect the ability of the transmitter to receive signals from the remote control.
Page 261 (Directional Arrows): Press these buttons to move through DVD menus. The up arrow will skip to the next chapter or track, the down arrow will take you to the beginning of the current chapter or track. Press the down arrow twice to take you to the previous chapter or track.
Page 262: Setup Menu
(Main Menu): Press this button to view the media menu. The media menu is different on every disc. Use the up, down, right, and left arrow buttons to move the cursor around the media menu. After making a selection, press the enter button. (Enter): Press this button to select the choice that is highlighted in any menu.
Page 263 Not all DVDs support all the feature defaults in the setup menus. In the event a particular feature is not supported, defaults will be provided by the DVD media. Exit the setup menu by pressing the return button on the remote control or the DVD player. If changes are made to the system setup defaults, the disc will resume play from the beginning and not where it previously left off.
Page 264 Problem Recommended Action No sound. The volume on the headphones could be too low. Adjust the volume on the right earpiece on the wireless headphones. If the DVD system is being heard through the vehicle speakers, adjust the volume from the radio. The radio must have the RSE enabled by using the CD, CD TAPE, or CD...
Page 265 Problem Recommended Action After stopping the player, I Press the stop button on push the play button but the remote control to sometimes the DVD starts resume where the DVD where I left off, and left off. Press the stop sometimes at the button twice to start the beginning.
Page 266 Problem Recommended Action My disc is stuck in the Press the eject button on player. The eject button the DVD player. Turn the does not work. power off, then on again, then press the eject button on the DVD player. Do not attempt to force or remove the disc from the player.
Page 267: Dvd Messages
DVD Messages The following errors may be displayed on the video screen. Disc Format Error: This message will be displayed if a disc is inserted upside down, if the disc is not readable, or if the disc format is not compatible. Disc Play Error: This message will be displayed if the mechanism can not play the disc.
Page 268: Navigation/Radio System
Navigation/Radio System Your vehicle may have a navigation radio system that includes Radio Data System (RDS) with Program Type (PTY) selections that will seek out the kind of music you want to listen to and XM™ Satellite Radio Service capabilities (if equipped). The radio can also communicate with the navigation system to broadcast announcements on traffic, weather, and emergency alert communications.
Page 269 Rear Seat Audio (RSA) Controls The following functions are controlled by the RSA system: SEEK : When listening to the radio, press the up or the down arrow to go to the next or the previous station and stay there. This function is inactive if the front seat passengers are listening to the radio.
Page 270: Theft-Deterrent Feature
The BAND button will not access XM™ Satellite Radio service when the front seat passengers are listening to the RSE system through the vehicle’s speakers and the rear seat passengers are using the wired headphones to listen to the RSA system. P.SET PROG (Preset Program): Press this button to scan through the preset radio stations set on the pushbuttons on the main radio.
Page 271: Audio Steering Wheel Controls
Audio Steering Wheel Controls If your vehicle has this feature, some audio controls can be adjusted at the steering wheel. They include the following: SOURCE: When listening to the radio, press this button to play a cassette tape, CD, or a DVD (if equipped). If a cassette tape, and CD, and/or DVD are loaded, the system will go to the tape play ﬁrst.
Page 272: Radio Reception
Radio Reception The range for most AM stations is greater than for FM, especially at night. The longer range can cause station frequencies to interfere with each other. Static can occur on AM stations caused by things like storms and power lines. Try reducing the treble to reduce this noise.
Page 273: Care Of Your Cds And Dvds
A non-scrubbing action, wet-type cleaner which uses a cassette with a fabric belt to clean the tape head can be used. This type of cleaning cassette will not eject on its own. A non-scrubbing action cleaner may not clean as thoroughly as the scrubbing type cleaner. The use of a non-scrubbing action, dry-type cleaning cassette is not recommended.
Page 274 NOTES 3-136...
Page 275: Driving Your Vehicle
Section 4 Your Driving, the Road, and Your Vehicle ...4-2 Driver Behavior ...4-2 Driving Environment ...4-2 Vehicle Design ...4-2 Defensive Driving ...4-3 Drunken Driving ...4-3 Control of a Vehicle ...4-6 Braking ...4-6 Anti-Lock Brake System (ABS) ...4-7 Braking in Emergencies ...4-9 Traction Control System (TCS) ...4-10 All-Wheel Drive (AWD) System ...4-11 Steering ...4-12...
Page 276: Your Driving, The Road, And Your Vehicle
Your Driving, the Road, and Your Vehicle Whenever we drive, we are taking on an important responsibility. This is true for any motor vehicle — passenger car, van, truck, sport utility. Driver behavior, the driving environment, and the vehicle’s design all affect how well a vehicle performs. But statistics show that the most important factor, by far, is how we drive.
Page 277: Defensive Driving
But driver behavior factors are far more often the cause of a utility vehicle rollover than are environmental or vehicle factors. Safe driver behavior and understanding the environment in which you will be driving can help avoid a rollover crash in any type of vehicle, including utility vehicles.
Page 278 In recent years, more than 16,000 annual motor vehicle-related deaths have been associated with the use of alcohol, with more than 300,000 people injured. Many adults — by some estimates, nearly half the adult population — choose never to drink alcohol, so they never drive after drinking.
Page 279 It is the amount of alcohol that counts. For example, if the same person drank three double martinis (3 ounces or 90 ml of liquor each) within an hour, the person’s BAC would be close to 0.12 percent. A person who consumes food just before or during drinking will have a somewhat lower BAC level.
Page 280: Control Of A Vehicle
There is something else about drinking and driving that many people do not know. Medical research shows that alcohol in a person’s system can make crash injuries worse, especially injuries to the brain, spinal cord, or heart. This means that when anyone who has been drinking —...
Page 281: Anti-Lock Brake System (Abs)
But even in three-fourths of a second, a vehicle moving at 60 mph (100 km/h) travels 66 feet (20 m). That could be a lot of distance in an emergency, so keeping enough space between your vehicle and others is important. And, of course, actual stopping distances vary greatly with the surface of the road (whether it is pavement or gravel);...
Page 282 Let us say the road is wet and you are driving safely. Suddenly, an animal jumps out in front of you. You slam on the brakes and continue braking. Here is what happens with ABS: A computer senses that wheels are slowing down. If one of the wheels is about to stop rolling, the computer will separately work the brakes at each wheel.
Page 283: Braking In Emergencies
Remember: Anti-lock does not change the time you need to get your foot up to the brake pedal or always decrease stopping distance. If you get too close to the vehicle in front of you, you will not have time to apply your brakes if that vehicle suddenly slows or stops.
Page 284: Traction Control System (Tcs)
Traction Control System (TCS) Your vehicle may have a traction control system that limits wheel spin. This is especially useful in slippery road conditions. The system operates only if it senses that one or both of the front wheels are spinning or beginning to lose traction.
Page 285: All-Wheel Drive (Awd) System
To turn the system off, press the TRAC OFF button located on the instrument panel switchbank. If the system is limiting wheel spin when you press the button, the message will go off, but the system will not turn off until there is no longer a current need to limit wheel spin.
Page 286: Steering
Steering Power Steering If you lose power steering assist because the engine stops or the system is not functioning, you can steer but it will take much more effort. Steering Tips Driving on Curves It is important to take curves at a reasonable speed. A lot of the “driver lost control”...
Page 287: Steering In Emergencies
Steering in Emergencies There are times when steering can be more effective than braking. For example, you come over a hill and ﬁnd a truck stopped in your lane, or a car suddenly pulls out from nowhere, or a child darts out from between parked cars and stops right in front of you.
Page 288: Off-Road Recovery
Off-Road Recovery You may ﬁnd that your right wheels have dropped off the edge of a road onto the shoulder while you’re driving. If the level of the shoulder is only slightly below the pavement, recovery should be fairly easy. Ease off the accelerator and then, if there is nothing in the way, steer so that your vehicle straddles the edge of the pavement.
Page 289: Loss Of Control
• Do not get too close to the vehicle you want to pass while you are awaiting an opportunity. For one thing, following too closely reduces your area of vision, especially if you are following a larger vehicle. Also, you will not have adequate space if the vehicle ahead suddenly slows or stops.
Page 290 Skidding In a skid, a driver can lose control of the vehicle. Defensive drivers avoid most skids by taking reasonable care suited to existing conditions, and by not overdriving those conditions. But skids are always possible. The three types of skids correspond to your vehicle’s three control systems.
Page 291: Driving At Night
Driving at Night Night driving is more dangerous than day driving. One reason is that some drivers are likely to be impaired — by alcohol or drugs, with night vision problems, or by fatigue. Here are some tips on night driving. •...
Page 292: Driving In Rain And On Wet Roads
You can be temporarily blinded by approaching headlamps. It can take a second or two, or even several seconds, for your eyes to re-adjust to the dark. When you are faced with severe glare, as from a driver who does not lower the high beams, or a vehicle with misaimed headlamps, slow down a little.
Page 293 The heavier the rain, the harder it is to see. Even if your windshield wiper blades are in good shape, a heavy rain can make it harder to see road signs and traffic signals, pavement markings, the edge of the road, and even people walking.
Page 294: Driving Through Flowing Water
Hydroplaning Hydroplaning is dangerous. So much water can build up under your tires that they can actually ride on the water. This can happen if the road is wet enough and you are going fast enough. When your vehicle is hydroplaning, it has little or no contact with the road.
Page 295: City Driving
City Driving One of the biggest problems with city streets is the amount of traffic on them. You will want to watch out for what the other drivers are doing and pay attention to traffic signals. Here are ways to increase your safety in city driving: •...
Page 296: Freeway Driving
Freeway Driving Mile for mile, freeways — also called thruways, parkways, expressways, turnpikes, or superhighways — are the safest of all roads. But they have their own special rules. 4-22 The most important advice on freeway driving is: Keep up with traffic and keep to the right. Drive at the same speed most of the other drivers are driving.
Page 297: Before Leaving On A Long Trip
When you want to leave the freeway, move to the proper lane well in advance. If you miss your exit, do not, under any circumstances, stop and back up. Drive on to the next exit. The exit ramp can be curved, sometimes quite sharply. The exit speed is usually posted.
Page 298: Highway Hypnosis
Highway Hypnosis Is there actually such a condition as highway hypnosis? Or is it just plain falling asleep at the wheel? Call it highway hypnosis, lack of awareness, or whatever. There is something about an easy stretch of road with the same scenery, along with the hum of the tires on the road, the drone of the engine, and the rush of the wind against the vehicle that can make you sleepy.
Page 299 If you drive regularly in steep country, or if you are planning to visit there, here are some tips that can make your trips safer and more enjoyable. • Keep your vehicle in good shape. Check all ﬂuid levels and also the brakes, tires, cooling system, and transaxle.
Page 300: Winter Driving
Winter Driving Here are some tips for winter driving: • Have your vehicle in good shape for winter. • You may want to put winter emergency supplies in your vehicle. 4-26 Also see Tires on page 5-55. Include an ice scraper, a small brush or broom, a supply of windshield washer ﬂuid, a rag, some winter outer clothing, a small shovel, a ﬂashlight, a red cloth, and a couple of reﬂective warning triangles.
Page 301 What is the worst time for this? Wet ice. Very cold snow or ice can be slick and hard to drive on. But wet ice can be even more trouble because it may offer the least traction of all. You can get wet ice when it is about freezing (32°F;...
Page 302: If You Are Caught In A Blizzard
Remember, unless you have anti-lock, if you brake so hard that your wheels stop rolling, you will just slide. Brake so your wheels always keep rolling and you can still steer. • Whatever your braking system, allow greater following distance on any slippery road. •...
Page 303 • Put on extra clothing or wrap a blanket around you. If you have no blankets or extra clothing, make body insulators from newspapers, burlap bags, rags, ﬂoor mats — anything you can wrap around yourself or tuck under your clothing to keep warm. You can run the engine to keep warm, but be careful.
Page 304: If You Are Stuck: In Sand, Mud, Ice Or Snow
Then, shut the engine off and close the window almost all the way to preserve the heat. Start the engine again and repeat this only when you feel really uncomfortable from the cold. But do it as little as possible. Preserve the fuel as long as you can. To help keep warm, you can get out of the vehicle and do some fairly vigorous exercises every half hour or so until help comes.
Page 305: Rocking Your Vehicle To Get It Out
Rocking Your Vehicle to Get It Out First, turn your steering wheel left and right. That will clear the area around your front wheels. If your vehicle has traction control, you should turn your traction control system off. See Traction Control System (TCS) on page 4-10.
Page 306 Tire and Loading Information Label Example Label A vehicle speciﬁc Tire and Loading Information label is attached to the center pillar (B-pillar) of your vehicle. With the driver’s door open, you will ﬁnd the label attached below the door lock post (striker). The tire and loading information label shows the number of occupant seating positions (A), and the maximum vehicle capacity weight (B) in kilograms and pounds.
Page 307 4. The resulting ﬁgure equals the available amount of cargo and luggage load capacity. For example, if the “XXX” amount equals 1400 lbs and there will be ﬁve 150 lb passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lbs (1400 750 (5 x 150) = 650 lbs).
Page 308 Example 2 Item Description Vehicle Capacity Weight for Example 2 Subtract Occupant Weight 150 lbs (68 kg) Available Cargo Weight 4-34 Total Item 1,000 lbs (453 kg) 750 lbs (340 kg) 250 lbs (113 kg) Refer to your vehicle’s tire and loading information label for speciﬁc information about your vehicle’s capacity weight and seating positions.
Page 309 Certiﬁcation/Tire Label United States version shown, Canada similar The Certiﬁcation/Tire label is found on the rear edge of the driver’s door. The label shows the gross weight capacity of your vehicle. This is called the Gross Vehicle Weight Rating (GVWR). The GVWR includes the weight of the vehicle, all occupants, fuel, and cargo.
Page 310: Towing
If you put things inside your vehicle—like suitcases, tools, packages, or anything else, they will go as fast as the vehicle goes. If you have to stop or turn quickly, or if there is a crash, they will keep going. CAUTION: Things you put inside your vehicle can strike and injure people in a sudden stop or turn, or...
Page 311: Dinghy Towing
Here are some important things to consider before you do recreational vehicle towing: • What’s the towing capacity of the towing vehicle? Be sure you read the tow vehicle manufacturer’s recommendations. • How far will you tow? Some vehicles have restrictions on how far and how long they can tow.
Page 312: Level Control
Level Control On vehicles equipped with automatic level control, the rear of the vehicle is automatically kept level as you load or unload your vehicle. However, you should still not exceed the GVWR or the GAWR. See Loading Your Vehicle on page 4-31. You may hear the compressor operating when you load or unload your vehicle, and periodically as the system self-adjusts.
Page 313: If You Do Decide To Pull A Trailer
Your vehicle can tow a trailer. To identify what the vehicle trailering capacity is for your vehicle, you should read the information in “Weight of the Trailer” that appears later in this section. But trailering is different than just driving your vehicle by itself. Trailering means changes in handling, acceleration, braking, durability, and fuel economy.
Page 314: Weight Of The Trailer
And, it can also depend on any special equipment that you have on your vehicle. You can ask your dealer for our trailering information or advice, or you can write us at: Buick Customer Assistance Center P.O. Box 33136 Detroit, MI 48232-5136 In Canada, write to:...
Page 315 If you are using a weight-carrying or weight distributing hitch, the trailer tongue weight (A) should be 10 percent to 15 percent of the total loaded trailer weight (B). Do not exceed the maximum allowable tongue weight for your vehicle. After you have loaded your trailer, weigh the trailer and then the tongue, separately, to see if the weights are proper.
Page 316: Safety Chains
Safety Chains You should always attach chains between your vehicle and your trailer. Cross the safety chains under the tongue of the trailer to help prevent the tongue from contacting the road if it becomes separated from the hitch. Instructions about safety chains may be provided by the hitch manufacturer or by the trailer manufacturer.
Page 317: Making Turns
Towing a trailer requires a certain amount of experience. Before setting out for the open road, you will want to get to know your rig. Acquaint yourself with the feel of handling and braking with the added weight of the trailer. And always keep in mind that the vehicle you are driving is now a good deal longer and not nearly as responsive as your vehicle is by itself.
Page 318: Turn Signals When Towing A Trailer
Turn Signals When Towing a Trailer When you tow a trailer, your vehicle has to have extra wiring. The arrows on your instrument panel will ﬂash whenever you signal a turn or lane change. Properly hooked up, the trailer lamps will also ﬂash, telling other drivers you are about to turn, change lanes or stop.
Page 319: Maintenance When Trailer Towing
When You Are Ready to Leave After Parking on a Hill 1. Apply your regular brakes and hold the pedal down while you: • Start your engine. • Shift into a gear. • Release the parking brake. 2. Let up on the brake pedal. 3.
Page 320 NOTES 4-46...
Page 321: Service And Appearance Care
Section 5 Service ...5-3 Doing Your Own Service Work ...5-4 Adding Equipment to the Outside of Your Vehicle ...5-5 Fuel ...5-5 Gasoline Octane ...5-5 Gasoline Speciﬁcations ...5-5 California Fuel ...5-6 Additives ...5-6 Fuels in Foreign Countries ...5-7 Filling Your Tank ...5-8 Filling a Portable Fuel Container ...5-10 Checking Things Under the Hood ...5-10 Hood Release ...5-11...
Page 322 Section 5 Tire Chains ...5-70 Accessory Inﬂator ...5-70 If a Tire Goes Flat ...5-72 Changing a Flat Tire ...5-72 Removing the Spare Tire and Tools ...5-74 Removing the Flat Tire and Installing the Spare Tire ...5-80 Secondary Latch System ...5-84 Storing a Flat or Spare Tire and Tools ...5-88 Compact Spare Tire ...5-94 Appearance Care ...5-95...
Page 323: Service
Service Your dealer knows your vehicle best and wants you to be happy with it. We hope you will go to your dealer for all your service needs. You will get genuine GM parts and GM-trained and supported service people. We hope you will want to keep your GM vehicle all GM.
Page 324: Doing Your Own Service Work
Doing Your Own Service Work If you want to do some of your own service work, you will want to use the proper service manual. It tells you much more about how to service your vehicle than this manual can. To order the proper service manual, see Service Publications Ordering Information on page 7-12.
Page 325: Adding Equipment To The Outside Of Your Vehicle
Adding Equipment to the Outside of Your Vehicle Things you might add to the outside of your vehicle can affect the airﬂow around it. This may cause wind noise and affect windshield washer performance. Check with your dealer before adding equipment to the outside of your vehicle.
Page 326: California Fuel
California Fuel If your vehicle is certiﬁed to meet California Emission Standards (see the underhood emission control label), it is designed to operate on fuels that meet California speciﬁcations. If this fuel is not available in states adopting California emissions standards, your vehicle will operate satisfactorily on fuels meeting federal speciﬁcations, but emission control system performance may be affected.
Page 327: Fuels In Foreign Countries
Gasolines containing oxygenates, such as ethers and ethanol, and reformulated gasolines may be available in your area to contribute to clean air. General Motors recommends that you use these gasolines, particularly if they comply with the speciﬁcations described earlier. Notice: Your vehicle was not designed for fuel that contains methanol.
Page 328: Filling Your Tank
Filling Your Tank CAUTION: Fuel vapor burns violently and a fuel ﬁre can cause bad injuries. To help avoid injuries to you and others, read and follow all the instructions on the pump island. Turn off your engine when you are refueling. Do not smoke if you are near fuel or refueling your vehicle.
Page 329 Be careful not to spill fuel. Do not top off or overﬁll the tank and wait a few seconds after you have ﬁnished pumping before removing the nozzle. Clean fuel from painted surfaces as soon as possible. See Washing Your Vehicle on page 5-98. When replacing the fuel cap, turn it to the right (clockwise) until it clicks.
Page 330: Filling A Portable Fuel Container
Filling a Portable Fuel Container CAUTION: Never ﬁll a portable fuel container while it is in your vehicle. Static electricity discharge from the container can ignite the gasoline vapor. You can be badly burned and your vehicle damaged if this occurs. To help avoid injury to you and others: •...
Page 331: Hood Release
Hood Release To open the hood, do the following: 1. Pull the hood release handle, located under the instrument panel on the driver’s side of the vehicle. 2. At the front of the vehicle, pull up on the center of the hood, and push the secondary hood release to the right.
Page 332: Engine Compartment Overview
Engine Compartment Overview When you lift the hood of the 3400 V6 engine, here is what you will see: 5-12...
Page 333 A. Underhood Fuse Block. See Underhood Fuse Block on page 5-107. B. Remote Positive (+) Terminal. See Jump Starting on page 5-42. C. Power Steering Fluid Reservoir. See Power Steering Fluid on page 5-36. D. Automatic Transaxle Fluid Dipstick. See “Checking the Fluid Level”...
Page 334 When you lift the hood of the 3.6L V6 engine, here is what you will see: 5-14...
Page 335 A. Windshield Washer Fluid Reservoir. See “Adding Washer Fluid” under Windshield Washer Fluid on page 5-37. B. Underhood Fuse Block. See Underhood Fuse Block on page 5-107. C. Battery. See Battery on page 5-41. D. Remote Positive (+) Terminal. See Jump Starting on page 5-42.
Page 336: Engine Oil
Engine Oil Checking Engine Oil It is a good idea to check your engine oil every time you get fuel. In order to get an accurate reading, the oil must be warm and the vehicle must be on level ground. The engine oil dipstick handle is a yellow loop.
Page 337 When to Add Engine Oil If the oil is below the cross-hatched area at the tip of the dipstick, then you will need to add at least one quart of oil. But you must use the right kind. This section explains what kind of oil to use.
Page 338 5-18 • SAE 5W-30 As shown in the viscosity chart, SAE 5W-30 is best for your vehicle. These numbers on an oil container show its viscosity, or thickness. Do not use other viscosity oils such as SAE 20W-50. Oils meeting these requirements should also have the starburst symbol on the container.
Page 339: Engine Oil Life System
Notice: Use only engine oil identiﬁed as meeting GM Standard GM6094M and showing the American Petroleum Institute Certiﬁed For Gasoline Engines starburst symbol. Failure to use the recommended oil can result in engine damage not covered by your warranty. ® GM Goodwrench oil meets all the requirements for your vehicle.
Page 340: How To Reset The Engine Oil Life System
If the system is ever reset accidentally, you must change your oil at 3,000 miles (5 000 km) since your last oil change. Remember to reset the oil life system whenever the oil is changed. How to Reset the Engine Oil Life System The Engine Oil Life System calculates when to change your engine oil and ﬁlter based on vehicle use.
Page 341: Engine Air Cleaner/Filter
Used oil can be a threat to the environment. If you change your own oil, be sure to drain all the oil from the ﬁlter before disposal. Never dispose of oil by putting it in the trash, pouring it on the ground, into sewers, or into streams or bodies of water.
Page 342: Automatic Transaxle Fluid
3. Unlatch the two hooks on top of the engine air cleaner/ﬁlter housing. 4. Inspect or replace the engine air cleaner/ﬁlter. 5. Align the tabs located on the bottom of the panel with the slots at the bottom of the housing. 6.
Page 343: How To Check Automatic Transaxle Fluid
How to Check Automatic Transaxle Fluid Because this operation can be a little difficult, you may choose to have this done at the dealership service department. If you do it yourself, be sure to follow all the instructions here, or you could get a false reading on the dipstick. Notice: Too much or too little ﬂuid can damage the transaxle.
Page 344 Then, without shutting off the engine, do the following: See Engine Compartment Overview on page 5-12 for information on dipstick location. If your vehicle is equipped with a 3400 V6 engine, the dipstick handle will be a red loop. 5-24 If your vehicle is equipped with a 3.6L V6 engine, the dipstick handle will...
Page 345: Engine Coolant
How to Add Automatic Transaxle Fluid Refer to the Maintenance Schedule to determine what kind of transaxle ﬂuid to use. See Recommended Fluids and Lubricants on page 6-12. If the ﬂuid level is low, add only enough of the proper ﬂuid to bring the level into the cross-hatched area on the dipstick.
Page 346: What Coolant To Use
What Coolant to Use Use a mixture of one-half clean, drinkable water and ® one-half DEX-COOL coolant which will not damage aluminum parts. If you use this coolant mixture, you do not need to add anything else. CAUTION: Adding only plain water to your cooling system can be dangerous.
Page 347: Checking Coolant
Checking Coolant The coolant recovery tank is located on the driver’s side of the vehicle, above the engine air cleaner/ﬁlter. See Engine Compartment Overview on page 5-12 for more information on location. The vehicle must be on a level surface. When your engine is cold, the coolant level should be at the FULL COLD mark, or a little higher.
Page 348: Radiator Pressure Cap
Radiator Pressure Cap Notice: The radiator cap on your vehicle is a pressure-type cap and must be tightly installed to prevent coolant loss and possible engine damage from overheating. Be sure the arrows on the cap line up with the overﬂow tube on the radiator ﬁller neck. The radiator pressure cap for the 3400 V6 engine and the 3.6L V6 engine are located in different areas of the engine compartment.
Page 349: If No Steam Is Coming From Your Engine
Notice: If your engine catches ﬁre because you keep driving with no coolant, your vehicle can be badly damaged. The costly repairs would not be covered by your warranty. See Overheated Engine Protection Operating Mode on page 5-30 for information on driving to a safe place in an emergency.
Page 350: Overheated Engine Protection Operating Mode
Overheated Engine Protection Operating Mode This emergency operating mode allows your vehicle to be driven to a safe place in an emergency situation. If an overheated engine condition exists, an overheat protection mode which alternates ﬁring groups of cylinders helps prevent engine damage. In this mode, you will notice a signiﬁcant loss in power and engine performance.
Page 351 3.6 L V6 engine A. Radiator Pressure Cap B. Electric Engine Cooling Fans C. Coolant Recovery Tank CAUTION: An electric engine cooling fan under the hood can start up even when the engine is not running and can injure you. Keep hands, clothing and tools away from any underhood electric fan.
Page 352 If there seems to be no leak, with the engine on, check to see if the electric engine cooling fans are running. If the engine is overheating, both fans should be running. If they are not, your vehicle needs service. Notice: Engine damage from running your engine without coolant is not covered by your warranty.
Page 353 CAUTION: You can be burned if you spill coolant on hot engine parts. Coolant contains ethylene glycol and it will burn if the engine parts are hot enough. Do not spill coolant on a hot engine. When the coolant in the coolant recovery tank is at or above the full cold mark, start your vehicle.
Page 354: How To Add Coolant To The Radiator
How to Add Coolant to the Radiator Notice: Your engine has a speciﬁc radiator ﬁll procedure. Failure to follow this procedure could cause your engine to overheat and be severely damaged. 1. You can remove the radiator pressure cap when the cooling system, including the radiator pressure cap and upper radiator hose, is no longer hot.
Page 355 3. If your vehicle has the 3400 V6 engine, after the engine cools, open the coolant air bleed valves. There are two bleed valves. One is located on the thermostat housing. The other is located on the thermostat bypass tube. 4.
Page 356: Power Steering Fluid
8. Then replace the pressure cap. At any time during this procedure if coolant begins to ﬂow out of the ﬁller neck, reinstall the pressure cap. Be sure the arrows on the pressure cap line up properly. 9. Then ﬁll the coolant recovery tank to the FULL COLD mark.
Page 357: Windshield Washer Fluid
How to Check Power Steering Fluid To check the power steering ﬂuid, do the following: 1. Turn the key off and let the engine compartment cool down. 2. Wipe the cap and the top of the reservoir clean. 3. Unscrew the cap and wipe the dipstick with a clean rag.
Page 358: Brakes
Adding Washer Fluid Open the cap with the washer symbol on it. Add washer ﬂuid until the tank is full. See Engine Compartment Overview on page 5-12 for reservoir location. Notice: • When using concentrated washer ﬂuid, follow the manufacturer’s instructions for adding water. •...
Page 359: What To Add
So, it is not a good idea to top off your brake ﬂuid. Adding brake ﬂuid will not correct a leak. If you add ﬂuid when your linings are worn, then you will have too much ﬂuid when you get new brake linings. You should add or remove brake ﬂuid, as necessary, only when work is done on the brake hydraulic system.
Page 360: Brake Wear
Brake Wear Your vehicle has four-wheel disc brakes. Disc brake pads have built-in wear indicators that make a high-pitched warning sound when the brake pads are worn and new pads are needed. The sound may come and go or be heard all the time your vehicle is moving, except when you are pushing on the brake pedal ﬁrmly.
Page 361: Battery
Replacing Brake System Parts The braking system on a vehicle is complex. Its many parts have to be of top quality and work well together if the vehicle is to have really good braking. Your vehicle was designed and tested with top-quality GM brake parts.
Page 362: Jump Starting
Jump Starting If your battery has run down, you may want to use another vehicle and some jumper cables to start your vehicle. Be sure to use the following steps to do it safely. CAUTION: Batteries can hurt you. They can be dangerous because: •...
Page 363 Notice: If you leave your radio or other accessories on during the jump starting procedure, they could be damaged. The repairs would not be covered by your warranty. Always turn off your radio and other accessories when jump starting your vehicle. 3.
Page 364 CAUTION: Using a match near a battery can cause battery gas to explode. People have been hurt doing this, and some have been blinded. Use a ﬂashlight if you need more light. Be sure the battery has enough water. You do not need to add water to the battery installed in your new vehicle.
Page 365 Notice: If you connect a negative cable to the ECM, ECM mounting bracket or any cables that attach to the ECM bracket, you may damage the ECM. Attach the negative cable to a heavy, unpainted metal engine part, other than the ECM, ECM bracket or cables attached to the ECM bracket.
Page 366 Notice: If the jumper cables are removed in the wrong order, electrical shorting may occur and damage the vehicle. The repairs would not be covered by your warranty. Remove the jumper cables in the correct order, making sure that the cables do not touch each other or other metal.
Page 367: All-Wheel Drive
All-Wheel Drive If you have an all-wheel-drive vehicle, be sure to perform the lubricant checks described in this section. All-wheel-drive vehicles have two additional systems that need lubrication. Transfer Case (Power Transfer Unit) When to Check Lubricant Refer to the Maintenance Schedule to determine how often to check the lubricant.
Page 368 Carrier Assembly-Differential (Rear Drive Module) When to Check and Change Lubricant Refer to the Maintenance Schedule to determine how often to check the lubricant and when to change it. See Scheduled Maintenance on page 6-4. How to Check Lubricant To get an accurate reading, the vehicle should be on a level surface.
Page 369: Bulb Replacement
Bulb Replacement For the proper type of replacement bulbs, see Replacement Bulbs on page 5-53. For any bulb changing procedure not listed in this section, contact your dealer. Halogen Bulbs CAUTION: Halogen bulbs have pressurized gas inside and can burst if you drop or scratch the bulb. You or others could be injured.
Page 370 6. Turn the bulb socket one-quarter of a turn clockwise. 7. Pull the bulb assembly out from the lamp housing. 5-50 8. Unhook the electrical connector by lifting up the gray tabs and separate the connector from the bulb base. 9.
Page 371: Front Turn Signal, Sidemarker And Parking Lamps
Front Turn Signal, Sidemarker and Parking Lamps To replace the front turn signal, parking or sidemarker lamp bulbs, follow the headlamp bulb replacement procedure and replace the appropriate bulb. Taillamps, Turn Signal, and Stoplamps 1. Open the liftgate. See Liftgate on page 2-11 for more information.
Page 372: Taillamps And Back-Up Lamps
Taillamps and Back-Up Lamps This procedure is for the liftgate-mounted taillamps and back-up lamps. 1. Open the liftgate. See Liftgate on page 2-11 for more information. 2. Remove the panel inside the liftgate by lifting the tabs and pulling the panel off. 3.
Page 373: Replacement Bulbs
10. Put the bulb assembly back into the lamp housing and turn the bulb socket one-quarter of a turn clockwise. 11. Replace the applique on the liftgate. 12. Gently lift the liftgate. 13. Reinstall the seven wing nuts and the four outboard nuts.
Page 374 4. Pull up the release clip, located at the connecting point of the blade and the arm. Then, pull the blade assembly down toward the glass to remove it from the wiper arm. 5. Push the new wiper blade securely on the wiper arm until you hear the release clip click into place.
Page 375: Tires
Tires Your new vehicle comes with high-quality tires made by a leading tire manufacturer. If you ever have questions about your tire warranty and where to obtain service, see your GM Warranty booklet for details. For additional information refer to the tire manufacturer’s booklet included with your vehicle’s Owner’s Manual.
Page 376: Tire Sidewall Labelling
Tire Sidewall Labelling Useful information about a tire is molded into its sidewall. The examples below show a typical passenger vehicle tire and a compact spare tire sidewall. Passenger (P-Metric) Tire Example (A) Tire Size: The tire size is a combination of letters and numbers used to deﬁne a particular tire’s width, height, aspect ratio, construction type and service description.
Page 377 Compact Spare Tire Example (A) Temporary Use Only: The compact spare tire or temporary use tire has a tread life of approximately 3,000 miles (5 000 km) and should not be driven at speeds over 65 mph (105 km/h). The compact spare tire is for emergency use when a regular road tire has lost air and gone ﬂat.
Page 378: Tire Terminology And Deﬁnitions
Tire Size The following illustration shows an example of a typical passenger vehicle tire size. (A) Passenger (P-Metric) Tire: The United States version of a metric tire sizing system. The letter P as the ﬁrst character in the tire size means a passenger vehicle tire engineered to standards set by the U.S.
Page 379 Aspect Ratio: The relationship of a tire’s height to its width. Belt: A rubber coated layer of cords that is located between the plies and the tread. Cords may be made from steel or other reinforcing materials. Bead: The tire bead contains steel wires wrapped by steel cords that hold the tire onto the rim.
Page 380 Normal Occupant Weight: The number of occupants a vehicle is designed to seat multiplied by 150 lbs (68 kg). See Loading Your Vehicle on page 4-31. Occupant Distribution: Designated seating positions. Outward Facing Sidewall: The side of an asymmetrical tire that has a particular side that faces outward when mounted on a vehicle.
Page 381: Inﬂation - Tire Pressure
Vehicle Placard: A label permanently attached to a vehicle showing the vehicle’s capacity weight and the original equipment tire size and recommended inﬂation pressure. See “Tire and Loading Information Label” under Loading Your Vehicle on page 4-31. Inﬂation - Tire Pressure Tires need the correct amount of air pressure to operate effectively.
Page 382: Check Tire Pressure System
How to Check Use a good quality pocket-type gage to check tire pressure. You cannot tell if your tires are properly inﬂated simply by looking at them. Radial tires may look properly inﬂated even when they are under-inﬂated. Check the tire’s inﬂation pressure when the tires are cold.
Page 383 If the anti-lock brake system warning light comes on, the check tire pressure system may not be working properly. See your dealer for service. Also, see Anti-Lock Brake System Warning Light on page 3-45. The check tire pressure system detects differences in tire rotation speeds that are caused by changes in tire pressure.
Page 384: Tire Inspection And Rotation
Tire Inspection and Rotation Tires should be rotated every 5,000 to 8,000 miles (8 000 to 13 000 km). Any time you notice unusual wear, rotate your tires as soon as possible and check wheel alignment. Also check for damaged tires or wheels. See When It Is Time for New Tires on page 5-65 and Wheel Replacement on page 5-68 for more information.
Page 385: When It Is Time For New Tires
CAUTION: Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after a time. The wheel could come off and cause an accident. When you change a wheel, remove any rust or dirt from places where the wheel attaches to the vehicle.
Page 386: Buying New Tires
Buying New Tires To ﬁnd out what kind and size of tires your vehicle needs, look at the tire and loading information label. For more information about this label and its location on your vehicle, see Loading Your Vehicle on page 4-31. The tires installed on your vehicle when it was new had a Tire Performance Criteria Speciﬁcation (TPC Spec) number on each tire’s sidewall.
Page 387: Uniform Tire Quality Grading
Uniform Tire Quality Grading Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width. For example: Treadwear 200 Traction AA Temperature A The following information relates to the system developed by the United States National Highway Traffic Safety Administration, which grades tires by treadwear, traction and temperature performance.
Page 388: Wheel Alignment And Tire Balance
Temperature – A, B, C The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a speciﬁed indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.
Page 389: Used Replacement Wheels
If you need to replace any of your wheels, wheel bolts or wheel nuts, replace them only with new GM original equipment parts. This way, you will be sure to have the right wheel, wheel bolts and wheel nuts for your vehicle. CAUTION: Using the wrong replacement wheels, wheel bolts or wheel nuts on your vehicle can be...
Page 390: Tire Chains
Tire Chains CAUTION: Don’t use tire chains. There’s not enough clearance. Tire chains used on a vehicle without the proper amount of clearance can cause damage to the brakes, suspension or other vehicle parts. The area damaged by the tire chains could cause you to lose control of your vehicle and you or others may be injured in a crash.
Page 391 CAUTION: Inﬂating something too much can make it explode, and you or others could be injured. Be sure to read the inﬂator instructions, and inﬂate any object only to its recommended pressure. To use your accessory inﬂator system, do the following: 1.
Page 392: If A Tire Goes Flat
If a Tire Goes Flat It’s unusual for a tire to “blowout” while you’re driving, especially if you maintain your tires properly. If air goes out of a tire, it’s much more likely to leak out slowly. But if you should ever have a “blowout,” here are a few tips about what to expect and what to do: If a front tire fails, the ﬂat tire will create a drag that pulls the vehicle toward that side.
Page 393 CAUTION: Changing a tire can be dangerous. The vehicle can slip off the jack and roll over or fall on you or other people. You and they could be badly injured or even killed. Find a level place to change your tire. To help prevent the vehicle from moving: 1.
Page 394: Removing The Spare Tire And Tools
Removing the Spare Tire and Tools The equipment you will need is located in the storage compartment on the passenger’s side, at the rear of the vehicle. 1. Open the jack storage compartment by lifting up the tab and pulling the cover off. 5-74 A.
Page 395 The tools you will be using include the jack (A), folding wrench (B), wing nut (C), and J-hook (D). Removing the Spare Tire (Vehicles without a Rear Convenience Center) The compact spare tire is located under the vehicle, behind the rear bumper. Use the spare tire hoist to raise, lower and store the compact spare tire.
Page 396 4. Tilt the retainer and slip it through the wheel opening to remove the spare tire from the cable. 5. Turn the wrench clockwise to raise the cable back up after removing the spare tire. Do not store a full-size or a ﬂat road tire under the vehicle.
Page 397 3. Loosen the cable by turning the wrench counterclockwise three or four turns. 4. If the spare tire has not lowered, tighten the cable all the way and then loosen it at least two times. If the spare tire did lower to the ground, continue with Step 4 under “Removing the Spare Tire (Vehicles without the Rear Convenience Center)”...
Page 398 1. Open the storage compartment door of the convenience center that is nearest the liftgate and remove the cap on the bottom of the storage compartment. 2. Flip the cut out carpet that is located through the hole of the storage compartment. 3.
Page 399 If the spare tire will not lower, the secondary latch may be engaged causing the tire not to lower. Do the following to check the cable: 1. Check under the vehicle to see if the cable is visible. 2. If it is not visible, see Secondary Latch System on page 5-84.
Page 400: Removing The Flat Tire And Installing The Spare Tire
Removing the Flat Tire and Installing the Spare Tire 1. If there is a wheel cover, loosen the plastic nut caps with the wheel wrench. They will not come off. Then, using the ﬂat end of the wheel wrench, pry along the edge of the cover until it comes off. Be careful;...
Page 401 CAUTION: Getting under a vehicle when it is jacked up is dangerous. If the vehicle slips off the jack you could be badly injured or killed. Never get under a vehicle when it is supported only by a jack. CAUTION: Raising your vehicle with the jack improperly positioned can damage the vehicle and even make the vehicle fall.
Page 402 CAUTION: Rust or dirt on the wheel, or on the parts to which it is fastened, can make the wheel nuts become loose after a time. The wheel could come off and cause an accident. When you change a wheel, remove any rust or dirt from the places where the wheel attaches to the vehicle.
Page 403 8. Lower the vehicle by attaching the folding wrench to the jack and turning the wrench counterclockwise. Lower the jack completely. CAUTION: Incorrect wheel nuts or improperly tightened wheel nuts can cause the wheel to come loose and even come off. This could lead to an accident.
Page 404: Secondary Latch System
9. Tighten the wheel nuts ﬁrmly in a crisscross sequence, as shown. Notice: Wheel covers will not ﬁt on your compact spare. If you try to put a wheel cover on the compact spare, you could damage the cover or the spare. 10.
Page 405 To release the spare tire from the secondary latch, do the following: CAUTION: Someone standing too close during the procedure could be injured by the jack. If the spare tire does not slide off the jack completely, make sure no one is behind you or on either side of you as you pull the jack out from the spare.
Page 406 Front-wheel-drive Vehicle shown 3. Attach the folding wrench to the jack and raise the jack at least 10 turns. 4. Place the jack under the vehicle, ahead of the rear bumper. Position the center lift point of the jack under the center of the spare tire. 5.
Page 407 8. Disconnect the wrench from the jack and carefully remove the jack. Use one hand to push against the spare tire while ﬁrmly pulling the jack out from under the spare tire with the other hand. 9. Tilt the retainer and slip it through the wheel opening when the spare tire has been completely lowered.
Page 408: Storing A Flat Or Spare Tire And Tools
Storing a Flat or Spare Tire and Tools Storing the Flat Tire (Vehicles without Stowable Seat and without Rear Convenience Center) A. D-Ring D. Valve Stem B. Wing Nut E. Full-Size Tire C. J-Hook 5-88 1. Flip up the D-ring located in the rear cargo area. 2.
Page 409 Storing the Flat Tire (Vehicles with a Rear Convenience Center) A. D-Ring E. Full-Size Tire B. Rear Convenience F. Cap on Bottom of Center Storage Compartment C. Wing Nut D. J-Hook 1. Open the center storage compartment door of the rear convenience center.
Page 410 Storing the Flat Tire (Vehicles with a Stowable Seat) A. Rear Convenience D. Stowable Seat Strap Center E. Cargo Net Hook B. Full-Size Tire F. J-Hook C. D-Ring G. Wing Nut 1. If the seatback is not in an upright position, move it to an upright position.
Page 411 Storing the Flat Tire (Vehicles with a Stowable Seatback Folded Flat) A. Stowable Seat D. J-Hook B. Full-Size Tire E. D-Ring C. Wing Nut 1. Fold the seatback down and ﬂip the D-ring up. 2. Lay the tire on the seatback with the valve stem pointing up with the center hole of the tire over the D-ring.
Page 412: Storing The Spare Tire And Tools
Storing the Spare Tire and Tools CAUTION: Storing a jack, a tire, or other equipment in the passenger compartment of the vehicle could cause injury. In a sudden stop or collision, loose equipment could strike someone. Store all these in the proper place. 5-92 CAUTION: The underbody-mounted spare tire needs to be...
Page 413 3. Tilt the retainer downward and slip it through the center hole of the spare tire. Make sure the retainer is fully seated across the underside of the wheel. 4. Attach the folding wrench to the hoist shaft. 5. Turn the folding wrench clockwise to lift the spare tire.
Page 414: Compact Spare Tire
When you replace the compact spare with a full-size tire, reinstall the bolt-on wheel covers or the center cap, whichever your vehicle has. Tighten them hand tight over the wheel nuts, using the folding wrench. Compact Spare Tire Although the compact spare tire was fully inﬂated when your vehicle was new, it can lose air after a time.
Page 415: Appearance Care
Appearance Care Cleaning products can be hazardous. Some are toxic. Other cleaning products can burst into ﬂames if a match is struck near them or if they get on a hot part of the vehicle. Some are dangerous if their fumes are inhaled in a closed space.
Page 416: Special Fabric Cleaning Problems
Most stains can be removed with club soda water. To clean, use the following instructions: 1. For liquids: blot with a clean, soft, white cloth. For solids: remove as much as possible and then vacuum or brush. 2. Apply club soda water to a clean, soft, white cloth. Do not over-saturate;...
Page 417: Vinyl
Stains caused by oil and grease can be cleaned with an approved GM cleaner and a clean, white cloth. 1. Carefully scrape off excess stain. 2. Clean with cool water and allow to dry completely. 3. If a stain remains, follow the “Using Cleaner on Fabric”...
Page 418: Glass Surfaces
Glass Surfaces Glass should be cleaned often. GM Glass Cleaner or a liquid household glass cleaner will remove normal tobacco smoke and dust ﬁlms on interior glass. See Vehicle Care/Appearance Materials on page 5-102. Notice: If you use abrasive cleaners when cleaning glass surfaces on your vehicle, you could scratch the glass and/or cause damage to the rear window defogger and the integrated radio antenna.
Page 419: Cleaning Exterior Lamps/Lenses
Cleaning Exterior Lamps/Lenses Use only lukewarm or cold water, a soft cloth and a car washing soap to clean exterior lamps and lenses. Follow instructions under Washing Your Vehicle on page 5-98. Finish Care Occasional waxing or mild polishing of the vehicle by hand may be necessary to remove residue from the paint ﬁnish.
Page 420: Aluminum Or Chrome-Plated Wheels
Aluminum or Chrome-Plated Wheels The vehicle may be equipped with either aluminum or chrome-plated wheels. Keep the wheels clean using a soft clean cloth with mild soap and water. Rinse with clean water. After rinsing thoroughly, dry with a soft clean towel. A wax may then be applied.
Page 421: Sheet Metal Damage
Sheet Metal Damage If the vehicle is damaged and requires sheet metal repair or replacement, make sure the body repair shop applies anti-corrosion material to parts repaired or replaced to restore corrosion protection. Original manufacturer replacement parts will provide the corrosion protection while maintaining the warranty.
Page 422: Vehicle Care/Appearance Materials
Vehicle Care/Appearance Materials See your GM dealer for more information on purchasing the following products. Description Polishing Cloth Interior and exterior Wax-Treated polishing cloth. Tar and Road Oil Removes tar, road oil, Remover and asphalt. Chrome Cleaner and Use on chrome or Polish stainless steel.
Page 423: Vehicle Identiﬁcation
Vehicle Identiﬁcation Vehicle Identiﬁcation Number (VIN) This is the legal identiﬁer for your vehicle. It appears on a plate in the front corner of the instrument panel, on the driver’s side. You can see it if you look through the windshield from outside your vehicle.
Page 424: Electrical System
Electrical System Add-On Electrical Equipment Notice: Don’t add anything electrical to your vehicle unless you check with your dealer ﬁrst. Some electrical equipment can damage your vehicle and the damage wouldn’t be covered by your warranty. Some add-on electrical equipment can keep other components from working as they should.
Page 425: Fuses And Circuit Breakers
Fuses and Circuit Breakers The wiring circuits in your vehicle are protected from short circuits by a combination of fuses, circuit breakers, and fusible thermal links. Look at the silver-colored band inside the fuse. If the band is broken or melted, replace the fuse. Be sure you replace a bad fuse with a new one of the identical size and rating.
Page 426 Fuse Empty Steering Wheel Radio Controls Power Door Locks Empty Empty Empty Empty Empty Empty Turn Signal and Hazard Lamp Flashers 5-106 Usage Fuse Usage Power Seats Electronic Level Control (ELC) Compressor Liftgate and Endgate Rear Auxiliary Power Outlet Electronic Level Control (ELC) Compressor Relay and Height Sensor Heated Mirrors...
Page 427: Underhood Fuse Block
Fuse Usage Power Sunroof Power Windows Map Lamps, Courtesy Lamps and Instrument Panel Lights Radio UQ3 Radio Ampliﬁer Head-Up Display Hazard Flashers Instrument Panel Cluster, Climate Control, Security LED and Remote Keyless Entry Mode ® PASS-Key Body Control Module (BCM) Advanced Occupant System Module Relay Usage...
Page 428 3400 V6 Engine Fuse Fuel Pump Air Conditioning Compressor Clutch Horn Engine Controls-Emissions and Sensors Power Control Module (PCM)-Battery Power Anti-Lock Brakes (ABS) Control Module Transaxle Solenoids 5-108 Usage Fuse Usage Anti-lock Brake System (ABS) Solenoid Valves Oxygen Sensors-Emissions Control Fuel Injectors Engine Controls Daytime Running Lamps (DRL)
Page 429 Fuse Usage Automatic Transaxle Shift Lock Control System Starter Solenoid Battery Fuse Anti-lock Brake System (ABS) Motor Engine Cooling Fan 2 Engine Cooling Fan 1 Main Battery Fuse for Retained Accessory Power Relay and Accessory Relay Main Battery Fuse for Heated Seats, Main Battery Fuse for Power Outlets, Level Control, Power Seats and Mirrors and Body Computer...
Page 430 3.6L V6 Engine Fuse Fuel Pump Air Conditioning Compressor Clutch Horn Anti-lock Brake System (ABS) Engine Control Module (ECM) Powertrain Relay Powertrain Sensors Transmission Control Module (TCM) Anti-lock Brake System (ABS) Solenoids Valves 5-110 Usage Fuse Usage Oxygen Sensor/MAF Sensor Fuel Injectors (Even) Fuel Injectors (Odd) Daytime Running Lamps (DRL)
Page 431 Fuse Usage Anti-lock Brake System (ABS) Motor Engine Cooling Fan 2 Engine Cooling Fan 1 Main Battery Fuse for Retained Accessory Power Relay and Accessory Relay Main Battery Fuse for Heated Seats, Air Conditioning, Defogger Main Battery Fuse for Power Outlets, Level Control, Power Seats, Mirrors, and Body Computer Main Battery Fuse for Climate...
Page 432: Capacities And Speciﬁcations
Capacities and Speciﬁcations The following approximate capacities are given in English and metric conversions. See Recommended Fluids and Lubricants on page 6-12 for more information. Application Air Conditioning Refrigerant R134a Automatic Transaxle – Front Wheel Drive Pan Removal and Replacement Complete Overhaul Automatic Transaxle –...
Page 433 Application Engine Oil with Filter 3400 V6 Engine 3.6L V6 Engine Fuel Capacity Rear Differential Fluid Capacity Transfer Case Fluid Capacity Wheel Nut Torque Engine 3400 V6 3.6L V6 4.0 quarts 5.5 quarts 18.0 gallons 2.1 quarts 0.6 pints Engine Speciﬁcations VIN Code Transaxle Automatic...
Page 434 NOTES 5-114...
Page 435 Section 6 Maintenance Schedule ...6-2 Introduction ...6-2 Maintenance Requirements ...6-2 Your Vehicle and the Environment ...6-2 Using Your Maintenance Schedule ...6-2 Scheduled Maintenance ...6-4 Additional Required Services ...6-6 Maintenance Footnotes ...6-7 Maintenance Schedule Owner Checks and Services ...6-8 At Each Fuel Fill ...6-8 At Least Once a Month ...6-9 At Least Once a Year ...6-9 Recommended Fluids and Lubricants ...6-12...
Page 436: Maintenance Schedule
Maintenance Schedule Introduction Important: Keep engine oil at the proper level and change as recommended. Have you purchased the GM Protection Plan? The Plan supplements your new vehicle warranties. See your Warranty and Owner Assistance booklet or your dealer for details. Maintenance Requirements Notice: Maintenance intervals, checks, inspections, replacement parts and recommended ﬂuids and...
Page 437 This schedule is for vehicles that: • carry passengers and cargo within recommended limits. You will ﬁnd these limits on the tire and loading information label. See Loading Your Vehicle on page 4-31. • are driven on reasonable road surfaces within legal driving limits.
Page 438: Scheduled Maintenance
Scheduled Maintenance When the CHANGE ENGINE OIL message comes on, it means that service is required for your vehicle. Have your vehicle serviced as soon as possible within the next 600 miles (1 000 km). It is possible that, if you are driving under the best conditions, the engine oil life system may not indicate that vehicle service is necessary for over a year.
Page 439 Scheduled Maintenance Service Maintenance I Maintenance II Change engine oil and ﬁlter. See Engine Oil on page 5-16. Reset oil life system. See Engine Oil Life System on page 5-19. An Emission Control Service. Visually check for any leaks or damage. See footnote (j). Inspect engine air cleaner ﬁlter.
Page 440: Additional Required Services
Additional Required Services The following services should be performed at the ﬁrst maintenance service (I or II) after the indicated miles (kilometers) shown for each item. Service and Miles (Kilometers) Inspect fuel system for damage or leaks. Inspect exhaust system for loose or damaged components.
Page 441: Maintenance Footnotes
Maintenance Footnotes † The U.S. Environmental Protection Agency or the California Air Resources Board has determined that the failure to perform this maintenance item will not nullify the emission warranty or limit recall liability prior to the completion of the vehicle’s useful life. We, however, urge that all recommended maintenance services be performed at the indicated intervals and the maintenance be recorded.
Page 442: Owner Checks And Services
(h) Change automatic transaxle ﬂuid and ﬁlter if the vehicle is mainly driven under one or more of these conditions: − In heavy city traffic where the outside temperature regularly reaches 90°F (32°C) or higher. − In hilly or mountainous terrain. −...
Page 443: At Least Once A Month
Engine Coolant Level Check Check the engine coolant level and add ® DEX-COOL coolant mixture if necessary. See Engine Coolant on page 5-25 for further details. Windshield Washer Fluid Level Check Check the windshield washer ﬂuid level in the windshield washer tank and add the proper ﬂuid if necessary.
Page 444: Ignition Transaxle Lock Check
Automatic Transaxle Shift Lock Control System Check CAUTION: When you are doing this inspection, the vehicle could move suddenly. If the vehicle moves, you or others could be injured. 1. Before you start, be sure you have enough room around the vehicle. It should be parked on a level surface.
Page 445: Underbody Flushing Service
Parking Brake and Automatic Transaxle Park (P) Mechanism Check CAUTION: When you are doing this check, your vehicle could begin to move. You or others could be injured and property could be damaged. Make sure there is room in front of your vehicle in case it begins to roll.
Page 446: Recommended Fluids And Lubricants
Recommended Fluids and Lubricants Fluids and lubricants identiﬁed below by name, part number or speciﬁcation may be obtained from your dealer. Usage Fluid/Lubricant Engine oil which meets GM Standard GM6094M and displays the American Petroleum Institute Certiﬁed for Gasoline Engines Engine Oil starburst symbol.
Page 447: Normal Maintenance Replacement Parts
Normal Maintenance Replacement Parts Replacement parts identiﬁed below by name, part number, or speciﬁcation can be obtained from your GM dealer. Part Engine Air Cleaner/Filter Engine Oil Filter 3400 V6 3.6L V6 Passenger Compartment Air Filter Kit Spark Plugs 3400 V6 3.6L V6 Windshield Wiper Blades (Hook Type) Driver’s Side –...
Page 448: Maintenance Record
Maintenance Record After the scheduled services are performed, record the date, odometer reading, who performed the service and the type of services performed in the boxes provided. See Maintenance Requirements on page 6-2 in this section. Any additional information from Owner Checks and Services on page 6-8 can be added on the following record pages. Also, you should retain all maintenance receipts.
Page 449 Maintenance Record (cont’d) Odometer Maintenance I or Date Serviced By Services Performed Reading Maintenance II 6-15...
Page 450 Maintenance Record (cont’d) Odometer Maintenance I or Date Serviced By Services Performed Reading Maintenance II 6-16...
Page 451: Customer Assistance And Information
Section 7 Customer Assistance and Information ...7-2 Customer Satisfaction Procedure ...7-2 Online Owner Center ...7-3 Customer Assistance for Text Telephone (TTY) Users ...7-4 Customer Assistance Offices ...7-4 GM Mobility Reimbursement Program ...7-5 Roadside Assistance Program ...7-6 Courtesy Transportation ...7-7 Vehicle Data Collection and Event Data Recorders ...7-10 Customer Assistance and Information Reporting Safety Defects ...7-11...
Page 452: Customer Assistance And Information
Information Customer Satisfaction Procedure Your satisfaction and goodwill are important to your dealer and to Buick. Normally, any concerns with the sales transaction or the operation of your vehicle will be resolved by your GM dealer’s sales or service departments. Sometimes, however, despite the best intentions of all concerned, misunderstandings can occur.
Page 453: Online Owner Center
The BBB Auto Line Program is an out of court program administered by the Council of Better Business Bureaus to settle automotive disputes regarding vehicle repairs or the interpretation of the New Vehicle Limited Warranty. Although you may be required to resort to this informal dispute resolution program prior to ﬁling a court action, use of the program is free of charge and your case will generally be heard within 40 days.
Page 454: Customer Assistance For Text Telephone (Tty) Users
To assist customers who are deaf, hard of hearing, or speech-impaired and who use Text Telephones (TTYs), Buick has TTY equipment available at its Customer Assistance Center. Any TTY user can communicate with Buick by dialing: 1-800-83-BUICK. TTY users in Canada can dial 1-800-263-3830.
Page 455: Gm Mobility Reimbursement Program
Overseas – Customer Assistance Please contact the local General Motors Business Unit. Mexico, Central America and Caribbean Islands/Countries (Except Puerto Rico and U.S. Virgin Islands) – Customer Assistance General Motors de Mexico, S. de R.L. de C.V. Customer Assistance Center Paseo de la Reforma # 2740 Col.
Page 456: Roadside Assistance Program
Roadside Assistance Program Call 1-800-252-1112 for Buick Roadside Assistance. As the proud owner of a new Buick vehicle, you are automatically enrolled in the Buick Roadside Assistance program. This value-added service is intended to provide you with peace of mind as you drive in the city or travel the open road.
Page 457: Courtesy Transportation
Buick Roadside Assistance: 1-800-252-1112, text telephone (TTY) users, call 1-888-889-2438. Buick reserves the right to limit services or reimbursement to an owner or driver when, in Buick’s judgement, the claims become excessive in frequency or type of occurrence. Roadside Assistance is not part of or included in the coverage provided by the New Vehicle Limited Warranty.
Page 458: Scheduling Service Appointments
Transportation Options Warranty service can generally be completed while you wait. However, if you are unable to wait Buick helps minimize your inconvenience by providing several transportation options. Depending on the circumstances,...
Page 459: Additional Program Information
Courtesy Rental Vehicle Your dealer may arrange to provide you with a courtesy rental vehicle or reimburse you for a rental vehicle that you obtain if your vehicle is kept for a warranty repair. Reimbursement will be limited to a maximum of $30 a day and must be supported by receipts.
Page 460: Vehicle Data Collection And Event Data Recorders
Vehicle Data Collection and Event Data Recorders Your vehicle, like other modern motor vehicles, has a number of sophisticated computer systems that monitor and control several aspects of the vehicle’s performance. Your vehicle uses on-board vehicle computers to monitor emission control components to optimize fuel economy, to monitor conditions for airbag deployment and, if so equipped, to provide anti-lock braking and to help the driver control the vehicle in difficult driving situations.
Page 461: Reporting Safety Defects
In addition, once GM collects or receives data, GM may: • use the data for GM research needs, • make it available for research where appropriate conﬁdentiality is to be maintained and need is shown, or • share summary data which is not tied to a speciﬁc vehicle with non-GM organizations for research purposes.
Page 462: Reporting Safety Defects To The Canadian Government
In addition to notifying NHTSA (or Transport Canada) in a situation like this, we certainly hope you will notify us. Please call us at 1-800-521-7300, or write: Buick Customer Assistance Center P.O. Box 33136 Detroit, MI 48232-5136 In Canada, please call us at 1-800-263-3777 (English) or 1-800-263-7854 (French).
Page 463: Current And Past Model Order Forms
Owner’s Information Owner publications are written speciﬁcally for owners and intended to provide basic operational information about the vehicle. The owner’s manual will include the Maintenance Schedule for all models. In-Portfolio: Includes a Portfolio, Owner’s Manual, and Warranty Booklet. RETAIL SELL PRICE: $35.00 Without Portfolio: Owner’s Manual only.
Page 464 NOTES 7-14...
Page 465 About Driving Your Vehicle ...ii Accessory Inﬂator ... 5-70 Accessory Power Outlets ... 3-26 Adding Equipment to Your Airbag-Equipped Vehicle ... 1-82 Additives, Fuel ... 5-6 Add-On Electrical Equipment ... 5-104 Air Cleaner/Filter, Engine ... 5-21 Air Conditioning ... 3-28, 3-30, 3-33 Airbag Passenger Status Indicator ...
Page 466 Appearance Care (cont.) Weatherstrips ... 5-98 Windshield, Backglass, and Wiper Blades ... 5-99 Ashtrays ... 3-27 Audio System(s) ... 3-75 Audio Steering Wheel Controls ... 3-133 Care of Your Cassette Tape Player ... 3-134 Care of Your CD and DVD Player ... 3-135 Care of Your CDs and DVDs ...
Page 467 California Fuel ... 5-6 Canadian Owners ... ii Capacities and Speciﬁcations ... 5-112 Captain Chairs, Rear ... 1-13 Carbon Monoxide ... 2-11, 2-29, 4-26, 4-38 Care of Safety Belts ... 5-98 Your Cassette Tape Player ... 3-134 Your CD and DVD Player ... 3-135 Your CDs and DVDs ...
Page 468 Cleaning (cont.) Tires ... 5-100 Underbody Maintenance ... 5-101 Vinyl ... 5-97 Washing Your Vehicle ... 5-98 Weatherstrips ... 5-98 Windshield, Backglass, and Wiper Blades ... 5-99 Climate Control System ... 3-28 Dual ... 3-30 Dual Automatic ... 3-33 Outlet Adjustment ... 3-36 Comfort Guides, Rear Safety Belt ...
Page 469 Door (cont.) Programmable Automatic Door Locks ... 2-10 Rear Door Security Locks ... 2-10 Driver Four-Way Manual Seat ... 1-3 Position, Safety Belt ... 1-25 Driver Behavior ... 4-2 Driver Information Center (DIC) ... 3-62 DIC Controls and Displays ... 3-64 DIC Vehicle Personalization ...
Page 470 Engine (cont.) Overheating ... 5-28 Reduced Power Message ... 3-53 Starting ... 2-21 Entry Lighting ... 3-17 Event Data Recorders (EDR) ... 7-10 Exit Delay, Headlamp ... 3-17 Exit Lighting ... 3-18 Extender, Safety Belt ... 1-42 Exterior Lamps ... 3-14 Filter Engine Air Cleaner ...
Page 471 Garage Door Opener ... 2-34 Gasoline Octane ... 5-5 Speciﬁcations ... 5-5 Glove Box ... 2-38 GM Mobility Reimbursement Program ... 7-5 Hatch Ajar Warning Message ... 3-56 Hazard Warning Flashers ... 3-6 Head Restraints ... 1-7 Headlamp Wiring ... 5-104 Headlamps Automatic Headlamp System ...
Page 472 Instrument Panel (cont.) Overview ... 3-4 Switchbank ... 3-20 Integrated Windshield Antenna ... 3-135 Interior Lamps ... 3-16 Interior Lamps Control ... 3-16 Jump Starting ... 5-42 Keyless Entry System ... 2-5 Keys ... 2-3 Labelling, Tire Sidewall ... 5-56 Lamps Battery Run-Down Protection ...
Page 473 Lockout Protection ... 2-11 Locks Delayed Locking ... 2-9 Door ... 2-8 Lockout Protection ... 2-11 Power Door ... 2-9 Programmable Automatic Door Locks ... 2-10 Rear Door Security Locks ... 2-10 Loss of Control ... 4-15 Low Brake Fluid Warning Message ... 3-59 Low Engine Oil Level Message ...
Page 474 Message (cont.) Low Oil Pressure ... 3-54 Low Tire ... 3-56 Low Washer Fluid Warning ... 3-58 Park Lamp Warning ... 3-61 ® PASS-Key III Security ... 3-57 Program Mode ... 3-60 Rear Hatch Ajar Warning ... 3-56 Reduced Engine Power ... 3-53 Remote Keyless Entry Transmitter Battery Low Warning ...
Page 475 Park Aid ... 3-24 Park Lamp Warning Message ... 3-61 Park (P) Shifting Into ... 2-27 Shifting Out of ... 2-28 Parking Assist ... 3-24 Brake ... 2-26 Over Things That Burn ... 2-29 Passenger Airbag Status Indicator ... 3-42 Passenger Sensing System ...
Page 476 Rear Reading Lamps ... 3-19 Rear Safety Belt Comfort Guides ... 1-40 Rear Seat Audio (RSA) ... 3-130 Rear Seat Entertainment System ... 3-115 Rear Seat Operation ... 1-8 Rear Seat Passengers, Safety Belts ... 1-34 Rear Storage Area ... 2-40 Rearview Mirrors ...
Page 477 Safety Belts (cont.) Rear Safety Belt Comfort Guides for Children and Small Adults ... 1-40 Rear Seat Passengers ... 1-34 Right Front Passenger Position ... 1-34 Safety Belt Extender ... 1-42 Safety Belt Use During Pregnancy ... 1-34 Safety Belts Are for Everyone ... 1-20 Shoulder Belt Height Adjuster ...
Page 478 Speciﬁcations, Capacities ... 5-112 Speedometer ... 3-39 Split Bench Seats ... 1-8 Starting Your Engine ... 2-21 Steering ... 4-12 Steering Wheel Controls, Audio ... 3-133 Steering Wheel, Tilt Wheel ... 3-6 Storage Areas Cell Phone Storage Area ... 2-39 Convenience Net ...
Page 479 Tires (cont.) Inspection and Rotation ... 5-64 Installing the Spare Tire ... 5-80 Removing the Flat Tire ... 5-80 Removing the Spare Tire and Tools ... 5-74 Secondary Latch System ... 5-84 Storing a Flat or Spare Tire and Tools ... 5-88 Tire Sidewall Labelling ...
Page 480 Vehicle Personalization DIC ... 3-66 Memory Seat ... 2-47 Ventilation Adjustment ... 3-36 Visors ... 2-15 Warning Lights, Gages and Indicators ... 3-37 Warnings Hazard Warning Flashers ... 3-6 Other Warning Devices ... 3-6 Safety and Symbols ... iii Vehicle Damage ... iv Washer Fluid Low Warning Message ...

Buick 2005 Rendezvous Owner's Manual

Section 1 Seats and Restraint Systems

Seats and Restraint Systems

Restraint System Check

Section 2 Features and Controls

Features and Controls

Keys

Doors and Locks

Windows

Theft-Deterrent Systems

Starting and Operating Your Vehicle

Mirrors

Onstar System

Homelink Transmitter

Storage Areas

Sunroof

Vehicle Personalization

Section 3 Instrument Panel

Instrument Panel Overview

Climate Controls

Warning Lights, Gages, and Indicators

Message Center

Driver Information Center (DIC)

Audio System(S)

Section 4 Driving Your Vehicle

Driving Your Vehicle

Your Driving, the Road, and Your Vehicle

Towing

Quick Links

Chapters

Related Manuals for Buick 2005 Rendezvous

Summary of Contents for Buick 2005 Rendezvous