Advertisement
1. Make sure all wires are properly connected
and installation is complete before you turn on
the heater.
Complete installation
After installation, turn your heater to the highest setting and let it run for 30 minutes. Some smoking may occur as the element initially
burns off residue from manufacturing.
If your heater shows signs of overheating, such as glowing red or repeatedly getting unusually hot and shutting off, immediately turn off
the circuit breaker and review the "KNOW YOUR VOLTAGE" section or call us.
If the high-temperature safety shutoff trips more than once a day, replace the heater.
Fan cycling with heat
The room temperature is controlled by a line voltage thermo-
stat built-in to the heater.
1. Turn fan switch to the "AUTO" position and turn the ther-
mostat knob fully clockwise.
2. When the room reaches your comfort level, turn the ther-
mostat knob counterclockwise until the heater turns off. The
heat and the fan will automatically cycle around this preset
temperature.
3. To reduce the room temperature, turn the knob counter-
clockwise. To increase the room temperature, turn the knob
clockwise.
About the high-temperature safety shutoff
The heater is protected by a temperature-limiting control. The high-temperature safety shutoff is designed to open the heater circuit
when excessive operating temperatures are detected. The problem must be assessed and the high-temperature safety shutoff must
be reset to resume operation.
Resetting the high-temperature safety shutoff
If the high-temperature safety shutoff has opened the heater circuit due to excessive operating
temperatures, the heater will not work until the high-temperature safety shutoff is pressed. Turn
the electrical power off at the electrical panel board (circuit breaker or fuse box). After allow-
ing the unit to cool for at least 10 minutes, and resolving the problem causing the limit to trip
(typically the heater is blocked or needs cleaning-see Maintenance Instructions); use a narrow,
pointed object to access the high-temperature safety shutoff button through the right center
section of the heater grill. Press FIRMLY, and be sure to listen and feel for a click, indicating it
has been reset.
For more effective and safer operation and to prolong the life of the
heater, read the Owner's Guide and follow the instructions. Failure
to properly maintain the heater will void any warranty and may
cause the heater to function improperly.
LIMITED TWO YEAR WARRANTY: Cadet will repair or replace
any Cadet NLW heater found to be defective within two years after
the date of purchase.
These warranties do not apply:
1. Damage occurs to the product through improper installation or
incorrect supply voltage;
2. Damage occurs to the product through improper maintenance,
misuse, abuse, accident, or alteration;
3. The use of unauthorized accessories or unauthorized com-
ponents constitutes an alteration and voids all warranties. Refer
to Cadet website or call customer service at 855.223.3887 or
360.693.2505 for list of authorized accessories and components.
4. Cadet's warranty is limited to repair or replacement.
OPERATING INSTRUCTIONS
How to Operate Your Heater
Resetting the high-temperature safety shutoff
2. Do not operate without grill.
3. Do not tamper with the high-temperature safety
shutoff.
Fan running continuously with intermittent heat
Determined by the thermostat setting
1. Turn the fan switch to the "FAN" position and turn
the thermostat knob fully clockwise.
2. When the room reaches your comfort level, turn
the thermostat knob counterclockwise until the heater
turns off. The heater will automatically cycle around
this preset temperature, however the fan will run con-
stantly.
3. To reduce the room temperature, turn the knob
counterclockwise. To increase the room temperature,
turn the knob clockwise.
Warranty
5. In the event Cadet elects to replace any part of your Cadet prod-
uct, the replacement parts are subject to the same warranties as
the product. The installation of replacement parts does not modify
or extend the underlying warranties. Replacement or repair of any
Cadet product or part does not create any new warranties.
If you believe your Cadet product is defective, please contact Cadet
during the warranty period, for instructions on how to have the
repair or replacement processed.
Parts and Service
Visit cadetheat.com/parts-service for information on where to
obtain parts and service.
Reduce-Reuse-Recycle
This product is made primarily of recyclable materials.
You can reduce your carbon footprint by recycling this
product at the end of its useful life. Contact your local
recycling support center for further recycling instruc-
tions.
Fan running
continuously
with no heat
1. Turn the fan
switch to the
"FAN" position.
2. Turn the
thermostat
knob just
above the
"OFF" position.
High-
temperature
safety
shutoff
Page 5
Advertisement
