Advertisement
Available languages
Available languages
Mini motorized tool: Clearing obstructions
1
Using your Dyson machine
Please read the "Important Safety Instructions" in this Dyson Operating Manual
before proceeding.
Operation
• Do not use outdoors or on wet surfaces or to vacuum water or other liquids – electric
shock could occur.
• Ensure the machine remains upright in use. Dirt and debris may be released if it is
turned upside down.
• Do not operate while checking for blockages as doing so could result in personal injury.
• For domestic indoor and car use only. Do not use it while the car is in motion or
while driving.
• To operate the MAX mode, locate the switch on the top of the machine. Slide the switch
to the Max mode position.
• To switch off MAX mode, slide the red switch back to the Powerful Suction
mode position.
• This machine has carbon fiber brushes. Take care if coming into contact with them, as
they may cause minor skin irritation. Wash your hands after handling the brushes.
Diagnostics – Lights during charging
Solid blue: Charging.
Flashing blue – Not charging – Re-fit charger or try
another socket. If warning light persists, contact the
Dyson Helpline.
Lights off: Charging complete.
Solid amber: Not charging, temporary fault
(e.g. too hot/cold).
Flashing red: Fault (contact Dyson Helpline).
Diagnostics – during use
Solid blue: 'ON'.
Flashing blue: No power, charge battery.
Flashing amber: No power, temporary fault
(e.g. too hot/cold).
Solid amber: Fault – if this persists contact
the Dyson Helpline.
Flashing red: Fault (contact Dyson Helpline).
10
Mini herramienta motorizada: Eliminación de obstrucciones
2
Docking station installation
• Use appropriate mounting hardware for your wall type and ensure that the docking
station is mounted securely. Ensure no pipe work (gas, water, air) or electrical cables,
wires or ductwork are located directly behind the mounting area. The docking station
must be mounted in accordance with regulations and applicable codes/standards
(state and local laws may apply). Dyson recommends the use of protective clothing,
eyeware and materials when installing the docking station.
Carpets or hard floors
• Before vacuuming your flooring, rugs and carpets, check the manufacturer's
recommended cleaning instructions.
• The brush bar on the machine can damage certain carpet types and floors. Some
carpets will fuzz if a rotating brush bar is used when vacuuming. If this happens, we
recommend vacuuming without the motorized floor tool and consulting with your
flooring manufacturer.
• Before vacuuming highly polished floors, such as wood or linoleum, first check that
the underside of the floor tool and its brushes are free from foreign objects that could
cause marking.
Looking after your Dyson machine
• Do not carry out any maintenance or repair work other than that shown and described
in this Dyson Operating Manual.
• Only use parts recommended by Dyson. If you do not this may invalidate
your warranty.
• Store the machine indoors. Do not use or store it below 37.4°F (3°C). Ensure the
machine is at room temperature before operating.
• Clean the machine only with a dry cloth. Do not use any lubricants, cleaning agents,
polishes or air fresheners on any part of the machine.
Vacuuming
• Do not use without the clear bin and filter in place.
• Fine dirt such as plaster dust or flour should only be vacuumed in very small amounts.
• Do not use the machine to pick up sharp hard objects, small toys, pins, paper clips, etc.
They may damage the machine.
• When vacuuming, certain carpets may generate small static charges in the clear bin
or wand. These are harmless and are not associated with the central electricity supply.
To minimize any effect from this, do not put your hand or insert any object into the clear
bin unless you have first emptied it. Clean the clear bin with a damp cloth only. (See
"Cleaning the clear bin".)
• Use extra care when cleaning on stairs.
• Do not rest the machine on chairs, tables, etc.
• Do not press down on the nozzle with excessive force when using the machine as this
may cause damage.
• Do not leave the cleaner head in one place on delicate floors.
• On waxed floors the movement of the cleaner head may create an uneven luster. If this
happens, wipe with a damp cloth, polish the area with wax, and wait for it to dry.
Emptying the clear bin
• Empty as soon as the dirt reaches the level of the MAX mark – do not overfill.
• Ensure the machine is disconnected from the charger before emptying the clear bin. Be
careful not to pull the "ON" trigger.
• To make emptying the clear bin easier, it is advisable to remove the wand and
floor tool.
• To minimize dust/allergen contact when emptying, encase the clear bin tightly in a
plastic bag and empty.
• To release the dirt, hold the machine by the handle, pull the red lever back and lift
upwards to release the cyclone. Continue until the bin base automatically opens and
releases the dirt.
• Remove the clear bin carefully from the bag.
• Seal the bag tightly, dispose as normal.
• To close, push the cyclone downwards until it is in the normal position and manually
close the base of the bin – the base will click when it is securely in place.
3
Advertisement
