Advertisement
(6)
If you don't want to make more ice, press
Ice Off
the Ice Off button. Pressing this button
(Hold 3 sec
3 second locks the display panel and
for Child lock)
dispenser buttons so the buttons can not
be used.The Child Lock icon lights up to
indicate you've activated the Child Lock
function.
(7)
Press the Cubed Ice or Crushed Ice
button to select the type of ice you want
Cubed Ice
dispensed. Each time you press the
(8)
button, the cubed and crushed ice modes
Crushed
alternate and the Cubed or Crushed ice
Ice
icon lights up, indicating your selection.
If you don't need ice, turn the function off
to save on water and energy consumption
(Cubed)
(Cubed) (Crushed)
(Crushed)
(See Ice Off below).
If you don't want to make more ice, press
( 9 )
the Ice Off button.
Ice Off
The icon will light up and the Ice-Maker
stops making ice.
We recommend you stop ice making if the
following occur:
-
There is enough ice in the ice bucket.
-
You want to save water and energy.
-
Water is not being supplied to the
refrigerator.
If the ice maker function is ON, and
the water line is not connected,
there will be a water valve noise
from back of the unit. Press the
Ice Off(6) button until the Ice Off
indicator (
Water fi lter usage
( 10 )
Filter
1. Normally the filter indicator is blue,
yellow, or green when you purchase or
install your refrigerator, depending on
your model.
2. After you use about 1020 L of water,
(Red)
(Red)
the filter indicator turns Light Pink.
(Reset the
(Reset the
(about 5 months)
indicator)
indicator)
3. After you use about 1135 L of water,
the filter indicator turns Red. (about
6 months) The icon will blink red for
several seconds when you open or
close the door.
4. Remove the old water filter and install a
new one when the filter indicator is red.
Reset the filter indicator by pressing
Alam/Hold 3 sec for Filter Reset button
for 3sec.
• If water is not dispensing or
• Some areas have large amounts
14_ operating
DA99-03404D-11.indb 14
DA99-03404D-11.indb 14
) illuminates.
dispensing slowly, you need to
replace the water filter because
the water filter is clogged.
of lime in their water, which
causes the water filter to clog
more quickly.
USING THE CONTROL PANEL
Basic temperature of Freezer and
Refrigerator Compartments
The basic temperature and/or recommended
temperature of Freezer and Refrigerator
Compartments are -19°C and 3°C respectively.
If the temperature of Freezer and Refrigerator
Compartments are too high or low, adjust the
temperature manually.
Controlling the Freezer temperature
The Freezer temperature can be set between -14ºC
and -22ºC to suit your particular needs. Press
the Freezer button repeatedly until the desired
temperature is shown in the temperature display.
The temperature will move 1°C degrees with each
press (-19°C → -20°C → -21°C → -22°C → -14°C →
-15°C → -16°C → -17°C → -18°C → -19°C). Keep
in mind that foods like ice cream may melt at 0°C.
The temperature display will move sequentially from
-22°C to -14°C.
Controlling the Refrigerator
temperature
The Refrigerator temperature can be set between 7ºC
and 1ºC to suit your particular needs. Press the Fridge
button repeatedly until the desired temperature is
shown in the temperature display.
The temperature will move 1°C degrees with each
press (3°C → 2°C → 1°C → 7°C → 6°C → 5°C → 4°C
→ 3°C). The temperature control process for the Fridge
works just like the Freezer process.
Press the Fridge button to set your desired
temperature. After a few seconds, the Fridge will begin
adjusting towards the newly set temperature. This will
be refl ected in the digital display.
- The temperature of the Freezer, fridge or
Convertible Room may rise when you open
the doors too frequently, or if a large amount
of warm or hot food is placed inside.
- This may cause the digital display to blink. Once
the Freezer and fridge temperature return to their
normal set temperatures, the blinking will stop.
- If the blinking continues, you may need to "reset"
the Refrigerator. Try unplugging the appliance, wait
for around 10 minutes and then plug the power
cord back in.
- If there is an communication error between the
Display and Main Controller, the Convertible Display
light may blink. Once the normal set temperatures
are reached, the blinking will stop. If the blinking
continues for a long period of time, please contact a
Samsung Electronics Service Center.
2015. 5. 7.
2015. 5. 7.
8:10
8:10
Advertisement
