Page 117: Table Of Contents
Instruments and Controls Controls Steering Wheel Adjustment . . . 5-2 Steering Wheel Controls ..5-2 Horn ......5-2 Windshield Wiper/Washer .
Page 118: Instruments And Controls
Instruments and Controls Controls Steering Wheel Adjustment To adjust the steering wheel: 1. Pull the lever down. 2. Move the steering wheel up, down, forward, and backward. 3. Pull the lever up to lock the steering wheel in place. Do not adjust the steering wheel while driving.
Page 119: Windshield Wiper/Washer
Windshield Wiper/Washer The windshield wiper lever is on the side of the steering column. With the ignition in ACC/ACCESSORY or ON/RUN, move the windshield wiper lever to select the wiper speed. 2: Use for fast wipes. 1: Use for slow wipes. (Adjustable Interval Wipes): Turn the band up for more frequent wipes or down for less frequent...
Page 120: Compass
Instruments and Controls Windshield Washer Pull the windshield wiper lever toward you to spray windshield washer fluid and activate the wipers. The wipers will continue until the lever is released or the maximum wash time is reached. When the windshield wiper lever is released, additional wipes may occur depending on how long the windshield washer had been...
Page 121: Clock
Clock The infotainment system controls are used to access the time and date settings through the menu system. See for information about how to use the menu system. Setting the Time and Date 1. Press the CONFIG button and select Time and Date Settings. 2.
Page 122 Instruments and Controls When adding electrical equipment, be sure to follow the installation instructions included with the equipment. See Hanging heavy equipment from the power outlet can cause damage not covered by the vehicle warranty. The power outlets are designed for accessory power plugs only, such as cell phone charge cords.
Page 123: Warning Lights, Gauges, And Indicators
The power outlet is not designed for and may not work properly, if any of the following is plugged in: Equipment with high initial peak wattage such as: compressor-driven refrigerators and electric power tools. Other equipment requiring an extremely stable power supply such as: microcomputer-controlled electric blankets, touch sensor...
Page 124: Instrument Cluster
Instruments and Controls Instrument Cluster English Automatic Transmission Shown, Manual and Metric Similar...
Page 125: Speedometer
Speedometer The speedometer shows the vehicle's speed in either kilometers per hour (km/h) or miles per hour (mph). Odometer The odometer shows how far the vehicle has been driven, in either kilometers or miles. This vehicle has a tamper resistant odometer.
Page 126: Engine Coolant Temperature
5-10 Instruments and Controls Here are four things that some owners ask about. None of these show a problem with the fuel gauge: At the service station, the fuel pump shuts off before the gauge reads full. It takes a little more or less fuel to fill up than the gauge indicated.
Page 127: Safety Belt Reminders
Safety Belt Reminders Driver Safety Belt Reminder Light There is a driver safety belt reminder light on the instrument panel cluster. When the engine is started this light begins to flash and a chime comes on for several seconds to remind the driver to fasten their safety belt.
Page 128: Passenger Airbag Status
5-12 Instruments and Controls The airbag readiness light comes on and stays on for several seconds when the vehicle is started. Then the light goes out. WARNING If the airbag readiness light stays on after the vehicle is started or comes on while driving, it means the airbag system might not be working properly.
Page 129: Charging System Light
If, after several seconds, both status indicator lights remain on, or if there are no lights at all, there may be a problem with the lights or the passenger sensing system. See your dealer for service. WARNING If the airbag readiness light ever comes on and stays on, it means that something may be wrong with the airbag system.
Page 130 5-14 Instruments and Controls Malfunctions often are indicated by the system before any problem is apparent. Heeding the light can prevent more serious damage to the vehicle. This system assists the service technician in correctly diagnosing any malfunction. If the vehicle is continually driven with this light on, after a while, the emission controls might not work as well,...
Page 131 Make sure the electrical system is not wet. The system could be wet if the vehicle was driven through a deep puddle of water. The condition is usually corrected when the electrical system dries out. A few driving trips should turn the light off. Make sure to fuel the vehicle with quality fuel.
Page 132: Brake System Warning
5-16 Instruments and Controls Brake System Warning Light The vehicle brake system consists of two hydraulic circuits. If one circuit is not working, the remaining circuit can still work to stop the vehicle. For normal braking performance, both circuits need to be working.
Page 133 The brake warning light should come on briefly when the ignition is placed in ON/RUN. If it does not come on, have the vehicle serviced by your dealer. If this light comes on, there is a problem with a system on the vehicle that is causing the parking brake system to work at a reduced level.
Page 134: Ultrasonic Parking Sensor
5-18 Instruments and Controls Ultrasonic Parking Sensor Light This light comes on to indicate that there is a malfunction in the system. See your dealer for service. for more information. Traction Off Light This light comes on briefly while starting the engine. If it does not, have the vehicle serviced by your dealer.
Page 135: Electronic Stability Control
Electronic Stability Control (ESC)/Traction Control System (TCS) Indicator/Warning Light The Electronic Stability Control (ESC)/Traction Control System (TCS) Indicator/Warning Light comes on briefly when the engine is started. If the light does not come on, have the vehicle serviced by the dealer. If the system is working normally, the indicator light turns off.
Page 136: Engine Oil Pressure Light
5-20 Instruments and Controls When the Light is On Steady This indicates that one or more of the tires are significantly underinflated. A tire pressure message can accompany the light. See for more information. Stop as soon as possible, and inflate the tires to the pressure value shown on the Tire and Loading Information label.
Page 137: Low Fuel Warning Light
Low Fuel Warning Light This light comes on for a few seconds when the ignition is turned on as a check to indicate it is working. If it does not come on, have it fixed. The low fuel warning light (A) comes on and a chime sounds periodically when the vehicle is low on fuel.
Page 138: Front Fog Lamp Light
5-22 Instruments and Controls Front Fog Lamp Light For vehicles with fog lamps, this light comes on when the fog lamps are in use. The light goes out when the fog lamps are turned off. See for more information. Lamps On Reminder For vehicles with the lamps on reminder light, it comes on when the lights are in use.
Page 139 DIC Operation and Displays The DIC has different displays which can be accessed by using the DIC buttons located on the turn signal lever located on the left side of the steering wheel. The DIC displays trip, fuel, and vehicle system information, and warning messages if a system problem is detected.
Page 140 5-24 Instruments and Controls Fuel Range This display shows the approximate distance the vehicle can be driven without refueling. The fuel range estimate is based on an average of the vehicle's fuel economy over recent driving history and the amount of fuel remaining in the fuel tank.
Page 141 Vehicle Information Menu Items Press MENU on the turn signal lever until Vehicle Information Menu is displayed. Use to scroll through the following menu items: Unit Tire Pressure Remaining Oil Life Unit Move to switch between Metric or US when the Unit display is active.
Page 142: Vehicle Messages
5-26 Instruments and Controls Vehicle Messages Messages displayed on the DIC indicate the status of the vehicle or some action that may be needed to correct a condition. Multiple messages may display one after the other. The messages that do not require immediate action can be acknowledged and cleared by pressing SET/CLR.
Page 143: Compass Messages
RELEASE PARK BRAKE SWITCH This message is displayed if the electric parking brake is on while the vehicle is in motion. Release it before you attempt to drive. See more information. SERVICE PARKING BRAKE This message is displayed when there is a problem with the electric parking brake.
Page 144: Engine Oil Messages
5-28 Instruments and Controls COOLANT LEVEL LOW ADD COOLANT This message will display if the coolant is low. See ENGINE OVERHEATED IDLE ENGINE This message displays when the engine coolant temperature is too hot. Stop and allow the vehicle to idle until it cools down.
Page 145: Engine Power Messages
Engine Power Messages ENGINE POWER IS REDUCED This message displays when the vehicle's engine power is reduced. Reduced engine power can affect the vehicle's ability to accelerate. If this message is on, but there is no reduction in performance, proceed to your destination.
Page 146: Messages
5-30 Instruments and Controls SERVICE STABILITRAK This message displays if there is a ® problem with the StabiliTrak system. If this message appears, try to reset the system. Stop; turn off the engine for at least 15 seconds; then start the engine again. If this message still comes on, it means there is a problem.
Page 147: Transmission Messages
TIRE LEARNING ACTIVE This message displays when the system is learning new tires. See for more information. Transmission Messages SERVICE TRANSMISSION This message displays if there is a problem with the transmission. See your dealer. SHIFT TO PARK This message displays when the transmission needs to be shifted to P (Park).
Page 148: Vehicle Personalization
5-32 Instruments and Controls Vehicle Personalization The audio system controls are used to access the personalization menus for customizing vehicle features. CONFIG (Configuration): Press to access the Configuration Settings Menu. Knob: Press the center of this knob to enter the menus and select menu items.
Page 149 Air Conditioning Mode This allows selection of automatic start of the air conditioning upon vehicle start. Selecting On indicates the air conditioning will be on when the vehicle is started. Selecting Off turns the air conditioning off each time the vehicle is started. Last Setting will resume the last setting when the vehicle was shut off.
Page 150 5-34 Instruments and Controls Comfort and Convenience Select the Comfort and Convenience menu and Chime Volume will be displayed. Chime Volume This allows the selection of the chime volume level. Press the knob when Chime Volume is highlighted. Turn the knob to select Normal or High.
Page 151: Power Door Locks
Exit Lighting This allows the selection of how long the exterior lamps stay on when leaving the vehicle when it is dark outside. Press the knob when Exit Lighting is highlighted. Turn the knob to select Off, 30 Seconds, 1 Minute, or 2 Minutes. Press the knob to confirm and go back to the last menu.
Page 152 5-36 Instruments and Controls Remote Lock/Unlock/Start Select Remote Lock/Unlock/Start and the following will be displayed: Remote Unlock Light Feedback Remote Lock Feedback Remote Door Unlock Remote Unlock Light Feedback When on, the exterior lamps will flash when unlocking the vehicle with the RKE transmitter.
Page 159: Infotainment System
Infotainment System Introduction Infotainment ....7-1 Theft-Deterrent Feature ..7-2 Overview ..... . 7-2 Operation .
Page 160: Theft-Deterrent Feature
Infotainment System Navigation System For vehicles with a navigation system, see the separate Navigation System Manual. Theft-Deterrent Feature The theft-deterrent feature works by learning a portion of the Vehicle Identification Number (VIN) to the infotainment system. The infotainment system does not operate if it is stolen or moved to a different vehicle.
Page 161 Radio: Seeks the previous station. CD: Select the previous track or rewinds within a track. D. CONFIG Opens the Settings menu. Radio: Seeks the next station. CD: Selects the next track or fast forwards within a track. Turns the system on or off and adjusts the volume.
Page 162: Operation
Infotainment System Operation Controls The infotainment system is operated by using the pushbuttons, multifunction knobs, menus shown on the display, and steering wheel controls, if equipped. Turning the System On or Off (Volume/Power): Press to turn the system on and off. Automatic Switch Off If the infotainment system has been turned on after the ignition is turned...
Page 163 Submenus An arrow on the right hand edge of the menu indicates that it has a submenu with other options. Activating a Setting 1. Turn the knob to highlight the setting. 2. Press the knob to activate the setting. Setting a Value 1.
Page 164 Infotainment System Audio Settings The audio settings can be set for each radio band and each audio player source. To quickly reset an audio setting value to 0: 1. Press the TONE button. 2. Select the audio setting. 3. Press and hold the knob until the value changes to 0.
Page 165 Adjusting the EQ (Equalizer) For vehicles that have an equalizer: 1. Press the TONE button. 2. Select EQ. 3. Select the setting. Press the BACK button to go back to the Tone Settings menu. System Settings Auto Volume The auto volume feature automatically adjusts the radio volume to compensate for road and wind noise as the vehicle speeds up...
Page 166: Radio
Infotainment System Configuring the Number of Favorites Pages To configure the number of available favorites pages: 1. Press the CONFIG button. 2. Select Radio Settings. 3. Select Radio Favorites. 4. Select the number of available favorites pages. 5. Press the BACK button to go back to the System Configuration menu.
Page 167 Selecting a Band Press the RADIO/BAND button to choose AM, FM, or XM , if equipped. The last station that was playing starts playing again. Selecting a Station Seek Tuning If the radio station is not known: Briefly press automatically search for the next available station.
Page 168 7-10 Infotainment System Updating Station & Category Lists If stations stored in the station list can no longer be received: 1. Press the knob. 2. Select Update AM or FM Station List, if the stations stored in the station list are no longer received.
Page 169: Satellite Radio
Satellite Radio Vehicles with an XM Satellite Radio tuner and a valid XM Satellite Radio subscription can receive XM programming. XM Satellite Radio Service XM is a satellite radio service based in the 48 contiguous United States and 10 Canadian provinces. XM Satellite Radio has a wide variety of programming and commercial-free music, coast to coast, and in...
Page 170 7-12 Infotainment System Selecting an XM Channel XM channels can be selected by station lists or category lists. Selecting a Channel by Station List XM channels can be selected by using , or the knob. To select an XM channel using , do one of the following:...
Page 171 XM Messages XL (Explicit Language Channels): These channels, or any others, can be blocked by request, by calling 1-800-929-2100 in the U.S. and 1-877-438-9677 in Canada. XM Updating: The encryption code in the receiver is being updated. No action is required. This process should take no longer than 30 seconds.
Page 172: Radio Reception
7-14 Infotainment System XM Not Available: If this message does not clear within a short period of time, the receiver could have a fault. Consult with your dealer. Radio Reception Frequency interference and static can occur during normal radio reception if items such as cellular phone chargers, vehicle convenience accessories, and external electronic devices are...
Page 173: Satellite Radio Antenna
If a cellular telephone antenna needs to be attached to the glass, make sure that the grid lines for the AM-FM antenna are not damaged. There is enough space between the grid lines to attach a cellular telephone antenna without interfering with radio reception.
Page 174 7-16 Infotainment System If the bottom surface of a disc is dirty, take a soft lint free cloth, or dampen a clean soft cloth in a mild neutral detergent solution mixed with water, and clean it. Wipe the disc from the center to the outer edge.
Page 175 Using the CD Menu: 1. Press the knob. 2. Select Tracks list. 3. Select the track. Playing Tracks in Random Order Press the knob and then set Shuffle Songs to On. Fast Forward and Rewind Press and hold fast forward or rewind within the current track.
Page 176: Auxiliary Devices
7-18 Infotainment System Auxiliary Devices This vehicle may have a 3.5 mm (1/8 in) auxiliary input jack and a USB port, located in the center console. Some portable audio ® devices such as iPods , MP3 players, and USB storage devices can be connected to the vehicle using a 3.5 mm (1/8 in) cable or a USB cable.
Page 177 USB Port For vehicles with a USB port, the following devices may be connected and controlled by the infotainment system: iPods PlaysForSure Devices (PFD) USB Drives ® Zunes Not all iPods, PFDs, USB Drives, and Zunes are compatible with the infotainment system.
Page 178 7-20 Infotainment System Connecting and Controlling a PlaysForSure Device (PFD) ® or Zune Connecting a PFD or Zune Connect the PFD or Zune to the USB port. Searching for a Track Tracks can be searched for by: Playlists Artists Albums Song Titles Podcasts Genres...
Page 179: Phone
Tracks can be searched for by: Playlists* Artists Albums Song Titles Genres Folder View *This only displays if a playlist is found on the device. To search for tracks: 1. Press the knob. 2. Select Search. 3. Select: Playlists, Artists, Albums, Song Titles, Genres, or Folder View.
Page 180 7-22 Infotainment System Steering Wheel Controls (Push to Talk): Press to answer incoming calls, confirm system information, and start voice recognition. (Mute/End Call): Press to end a call, reject a call, or cancel an operation. Infotainment System Controls For information about how to navigate the menu system using the infotainment controls, see (Phone): Press to enter the...
Page 181: Bluetooth
Bluetooth (Infotainment Controls) For information about how to navigate the menu system using the infotainment controls, see Pairing A Bluetooth enabled cell phone must be paired to the Bluetooth system first and then connected to the vehicle before it can be used. See the cell phone manufacturer's user guide for Bluetooth functions before pairing the cell phone.
Page 182 7-24 Infotainment System 5. Start the pairing process on the cell phone that will be paired to the vehicle. Reference the cell phone manufacturer's user guide for information on this process. Locate the device named General Motors or Your Vehicle in the list on the cell phone and follow the instructions on the cell phone to enter the four digit PIN provided by the...
Page 183 Making a Call 1. Press the button twice. 2. Enter the character sequence. See Entering a Character Sequence in for more information. 3. Select Call to start dialing the number. Accepting or Declining a Call When a call is received, the infotainment system mutes and a ring tone is heard in the vehicle.
Page 184: Bluetooth
7-26 Infotainment System Ending a Call Press the knob and select Hang Up. Muting a Call To Mute a Call Press the knob and select Mute Call. To Cancel Mute Press the knob and select Mute Call. Dual Tone Multi-Frequency (DTMF) Tones The in vehicle Bluetooth system can send numbers during a call.
Page 185 Pairing information: Up to five cell phones can be paired to the Bluetooth system. The pairing process is disabled when the vehicle is moving. The Bluetooth system links with the first available paired cell phone in the order the phone was paired.
Page 186 7-28 Infotainment System Listing All Paired and Connected Phones 1. Press For vehicles without a navigation system, the system responds Ready, followed by a tone. For vehicles with a navigation system, the system responds with a tone. After the tone, say Hands Free.
Page 187 Linking to a Different Phone 1. Press For vehicles without a navigation system, the system responds Ready, followed by a tone. For vehicles with a navigation system, the system responds with a tone. After the tone, say Hands Free. The system responds Ready, followed by a tone.
Page 188 7-30 Infotainment System 3. Say the complete phone number to be stored without pausing. If the system recognizes the number, the response is OK, Storing. If the system does not recognize the phone number, the response is Store <Phone number>. Please say yes or no.
Page 189 3. Say the first digit to be stored. The system will repeat back the digit it heard followed by a tone. Continue entering digits until the number to be stored is complete. If an unwanted number is recognized by the system, say Clear at any time to clear the last number.
Page 190 7-32 Infotainment System Deleting Name Tags The system uses the following commands to delete name tags: Delete Delete all name tags Using the Delete Command The delete command is used to delete specific name tags. To delete name tags: 1. Press For vehicles without a navigation system, the system responds Ready,...
Page 191 2. Say Delete all name tags. The system responds You are about to delete all name tags stored in your phone directory and your route destination directory. Are you sure you want to do this? Please say yes or no. Say Yes to delete all name tags.
Page 192 7-34 Infotainment System Using the Digit Dial Command 1. Press For vehicles without a navigation system, the system responds Ready, followed by a tone. For vehicles with a navigation system, the system responds with a tone. After the tone, say Hands Free.
Page 193 3. Say the name tag of the person to call. If the system recognizes the name tag, it responds OK, calling <name tag> and dials the number. If the system does not recognize the name tag, it confirms the name tag followed by a tone.
Page 194 7-36 Infotainment System Three Way Calling Three way calling must be supported on the Bluetooth phone and enabled by the wireless service carrier. 1. While on a call, press . The system responds with Ready, followed by a tone. 2. Say Three way call. The system responds with Three way call, please say dial or call.
Page 195 To Transfer Audio to the In-Vehicle Bluetooth System The cell phone must be paired and connected with the Bluetooth system before a call can be transferred. The connection process can take up to two minutes after the ignition is turned to ON/RUN or ACC/ACCESSORY.
Page 196 7-38 Infotainment System Sending a Number During a Call 1. Press . The system responds Ready, followed by a tone. 2. Say Dial. The system responds Say a number to send tones, followed by a tone. 3. Say the number to send. If the system recognizes the number, it responds OK, Sending Number and...
Page 253 General Information ..10-2 California Proposition 65 Warning ....10-3 California Perchlorate Materials Requirements ..10-3 Accessories and Modifications .
Page 254 Tire Pressure Monitor Operation ....10-55 Tire Inspection ....10-58 Tire Rotation ....10-59 When It Is Time for New Tires .
Page 255 Most motor vehicles, including this one, contain and/or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Engine exhaust, many parts and systems, many fluids, and some component wear by-products contain and/or emit these chemicals.
Page 256 GM Accessories are designed to complement and function with other systems on the vehicle. Your GM dealer can accessorize the vehicle using genuine GM Accessories. When you go to your GM dealer and ask for GM Accessories, you will know that GM-trained and supported service technicians will perform the work using genuine GM Accessories.
Page 257 To open the hood: 1. Pull up on the hood release handle with this symbol on it. It is located inside the vehicle to the left of the steering column. 2. Go to the front of the vehicle and push up on the secondary hood release handle.
Page 259 B. Engine Cover. C. Engine Oil Dipstick. See D. Engine Oil Fill Cap. See E. Transmission Fluid Cap and Dipstick. See Power Steering Fluid Reservoir and Cap. See G. Brake Master Cylinder and Hydraulic Clutch Reservoir (if equipped with manual transmission).
Page 261 B. Engine Cover. C. Engine Oil Fill Cap. See D. Engine Oil Dipstick. See E. Transmission Fluid Cap and Dipstick. See Brake Master Cylinder Reservoir. See G. Power Steering Fluid Reservoir and Cap. See H. Engine Coolant Reservoir and Pressure Cap. See Battery Cover.
Page 262 It is a good idea to check the engine oil level at each fuel fill. In order to get an accurate reading, the oil must be warm and the vehicle must be on level ground. The engine oil dipstick handle is a yellow loop. See for the location of the engine oil dipstick.
Page 263 Selecting the right engine oil depends on both the proper oil specification and viscosity grade: Use and ask for engine oils with the dexos certification mark. Oils meeting the requirements of the vehicle should have the dexos certification mark on the container. This certification mark indicates that the oil has been approved to the dexos...
Page 264 This vehicle was filled at the factory with dexos approved engine oil. Use of Substitute Engine Oils if dexos is unavailable for top up only: Engine oil not meeting the dexos specification or equivalent should not be used for an oil change.
Page 265 Cold Temperature Operation: In an area of extreme cold, where the temperature falls below 29°C ( 20°F), an SAE 0W-30 oil should be used. An oil of this viscosity grade will provide easier cold starting for the engine at extremely low temperatures.
Page 266 This vehicle has a computer system that indicates when to change the engine oil and filter. This is based on engine revolutions and engine temperature, and not on mileage. Based on driving conditions, the mileage at which an oil change is indicated can vary considerably.
Page 267 If the CHANGE ENGINE OIL message comes back on when the vehicle is started, the engine oil life system has not been reset. Repeat the procedure. It is not necessary to check the transmission fluid level. A transmission fluid leak is the only reason for fluid loss.
Page 268 Visually check the brake/clutch fluid reservoir to make sure the fluid level is at the MIN (minimum) line on the side of the reservoir. The brake/ hydraulic clutch fluid system should be closed and sealed. Do not remove the cap to check the fluid level or to top off the fluid level.
Page 269 4. Remove the screws (C) on top of the engine air cleaner/filter housing. 5. Lift the filter cover housing away from the engine. 6. Pull out the filter. 7. Inspect or replace the engine air cleaner/filter. 8. Reverse Steps 2 through 4 to reinstall the filter cover housing.
Page 270 The cooling system allows the engine to maintain the correct working temperature. When it is safe to lift the hood: A. Electric Engine Cooling Fans B. Coolant Surge Tank and Pressure Cap A. Electric Engine Cooling Fans B. Coolant Surge Tank and Pressure Cap An electric engine cooling fan under the hood can start up even...
Page 271 The cooling system in the vehicle is ® filled with DEX-COOL engine coolant. This coolant is designed to remain in the vehicle for 5 years or 240 000 km (150,000 miles), whichever occurs first. The following explains the cooling system and how to check and add coolant when it is low.
Page 272 Never dispose of engine coolant by putting it in the trash, pouring it on the ground, or into sewers, streams, or bodies of water. Have the coolant changed by an authorized service center, familiar with legal requirements regarding used coolant disposal. This will help protect the environment and your health.
Page 273 Adding only plain water or some other liquid to the cooling system can be dangerous. Plain water and other liquids, can boil before the proper coolant mixture will. The coolant warning system is set for the proper coolant mixture. With plain water or the wrong mixture, the engine could get too hot but you would not get the overheat warning.
Page 274 3. Fill the coolant surge tank with the proper DEX-COOL coolant mixture to the indicated level mark. 4. With the coolant surge tank pressure cap off, start the engine and let it run until you can feel the upper radiator hose getting hot.
Page 275 Steam from an overheated engine can burn you badly, even if you just open the hood. Stay away from the engine if you see or hear steam coming from it. Just turn it off and get everyone away from the vehicle until it cools down. Wait until there is no sign of steam or coolant before you open the hood.
Page 276 for reservoir location. It is not necessary to regularly check power steering fluid unless a leak is suspected in the system, or an unusual noise is heard. A fluid loss in this system could indicate a problem. Have the system inspected and repaired.
Page 277 When windshield washer fluid is needed, be sure to read the manufacturer's instructions before use. If operating the vehicle in an area where the temperature may fall below freezing, use a fluid that has sufficient protection against freezing. Open the cap with the washer symbol on it.
Page 278 This vehicle has disc brakes. Disc brake pads have built-in wear indicators that make a high-pitched warning sound when the brake pads are worn and new pads are needed. The sound can come and go or be heard all the time the vehicle is moving, except when applying the brake pedal firmly.
Page 279 The brake/clutch master cylinder reservoir is filled with DOT 4 brake fluid as indicated on the reservoir cap. See for the location of the reservoir. There are only two reasons why the brake fluid level in the reservoir might go down: The brake fluid level goes down because of normal brake lining wear.
Page 280 When the brake/clutch fluid falls to a low level, the brake warning light comes on. See Use only new DOT 4 brake fluid from a sealed container. It is recommended that the brake/clutch hydraulic system be flushed and refilled with new DOT 4 fluid at a regular maintenance service every two years.
Page 281 Refer to the replacement number shown on the original battery label when a new battery is needed. See for battery location. Battery posts, terminals, and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and reproductive harm.
Page 282 3. For automatic transmission vehicles, try to start the engine in each gear. The vehicle should start only in P (Park) or N (Neutral). If the vehicle starts in any other position, contact your dealer for service. For manual transmission vehicles, put the shift lever in Neutral, push the clutch pedal down halfway, and try to start...
Page 283 When you are doing this check, the vehicle could begin to move. You or others could be injured and property could be damaged. Make sure there is room in front of the vehicle in case it begins to roll. Be ready to apply the regular brake at once should the vehicle begin to move.
Page 284 To replace the wiper blade: 1. Pull the wiper assembly away from the windshield. 2. Lift up on the latch in the middle of the wiper blade where the wiper arm attaches. 3. With the latch open, pull the wiper blade down toward the windshield far enough to release it from the J-hooked end of the wiper arm.
Page 285 For the proper type of replacement bulbs, see For any bulb changing procedure not listed in this section, contact your dealer. Halogen bulbs have pressurized gas inside and can burst if you drop or scratch the bulb. You or others could be injured. Be sure to read and follow the instructions on the bulb package.
Page 286 1. For the driver side bulb, remove the windshield washer bottle filler neck by firmly pulling it straight up and out of the bottle. 2. Remove the outside cap for the low-beam headlamp/DRL bulb replacement from the back of the headlamp assembly.
Page 287 To replace the fog lamp bulb: 1. Locate the bulb assembly under the front fascia. 2. Disconnect the electrical connector from the bulb assembly. 3. Remove the bulb by turning it counterclockwise and pulling it straight out of the assembly. 4.
Page 288 A. Back-up Lamp B. Taillamp C. Stop/Turn Signal Lamp D. Taillamp/Sidemarker Lamp 5. Turn the bulb socket counterclockwise to remove it. 6. Pull the bulb from the socket. 7. Install a new bulb. 8. Turn the bulb socket clockwise to install it. 9.
Page 289 5. Push the replacement bulb straight into the bulb socket and turn the bulb socket clockwise to install it into the lamp assembly. 6. Push the lamp assembly back into position until the release tab locks into place. Back-up Lamp 4157 K Fog Lamp Front Turn...
Page 290 Fuses and circuit breakers protect the following in the vehicle: Headlamp Wiring Windshield Wiper Motor Power Windows and Other Power Accessories Replace a bad fuse with a new one of the identical size and rating. If there is a problem on the road and a fuse needs to be replaced, the same amperage fuse can be borrowed.
Page 291 To remove the fuse block cover, press the three retaining clips on the cover and lift it straight up. Transmission Control Module Engine Control Module Not Used Not Used...
Page 292 Ignition, Transmission Control Module, Engine Control Module Windshield Wiper Not Used Fuel Injection, Ignition System Even Fuel Injection, Ignition System Odd Engine Control Module Oxygen Sensor Starter Fuel System Control Module Secondary Air Induction Not Used Vacuum Pump Ignition, Airbag Not Used Not Used Not Used...
Page 293 Radiator Fan 1 Not Used Headlamp Washer System (if equipped) Radiator Fan 2 Terminal 87, Main Relay Oxygen Sensor Fog Lamps Right Hand Low Beam, High Intensity Discharge Headlamp Left Hand Low Beam, High Intensity Discharge Headlamp Horn Motor Indicator Lamp Ignition, Inside Rearview Mirror Not Used...
Page 294 Not Used Cooling Fan (LHU) Cooling Fan (LAF/LHU) High Intensity Discharge Lamps Ignition Secondary AIR Pump Window/Mirror Defog The instrument panel fuse block is located in the instrument panel, on the driver side of the vehicle. To access the fuses, open the storage compartment.
Page 295 Radio Displays, Park Assist, Infotainment, Module Tunnel Control Power Outlet 1 Power Outlet 2 Body Control Module 3 Body Control Module 4 Body Control Module 8 Front Heater Ventilation Air Conditioning/Blower Right Hand Power Front Seat Left Hand Power Front Seat Diagnostic Link Connector Airbag...
Page 296 Your new vehicle comes with high-quality tires made by a leading tire manufacturer. If you ever have questions about your tire warranty and where to obtain service, see your vehicle Warranty booklet for details. For additional information refer to the tire manufacturer. Poorly maintained and improperly used tires are dangerous.
Page 297 If you expect to drive on snow or ice covered roads often, you may want to get winter tires for the vehicle. All season tires provide good overall performance on most surfaces but they may not offer the traction you would like or the same level of performance as winter tires on snow or ice covered roads.
Page 298 Original equipment tires designed to GM's specific tire performance criteria have a TPC specification code molded onto the sidewall. GM's TPC specifications meet or exceed all federal safety guidelines. Department of Transportation (DOT) code indicates that the tire is in compliance with the U.S.
Page 299 compact spare tire or temporary use tire has a tread life of approximately 5 000 km (3,000 miles) and should not be driven at speeds over 105 km/h (65 mph). The compact spare tire is for emergency use when a regular road tire has lost air and gone flat.
Page 300 The following is an example of a typical passenger vehicle tire size. The United States version of a metric tire sizing system. The letter P as the first character in the tire size means a passenger vehicle tire engineered to standards set by the U.S.
Page 301 A rubber coated layer of cords that is located between the plies and the tread. Cords may be made from steel or other reinforcing materials. The tire bead contains steel wires wrapped by steel cords that hold the tire onto the rim.
Page 302 tire used on light duty trucks and some multipurpose passenger vehicles. An assigned number ranging from 1 to 279 that corresponds to the load carrying capacity of a tire. The maximum air pressure to which a cold tire can be inflated. The maximum air pressure is molded onto the sidewall.
Page 303 A metal support for a tire and upon which the tire beads are seated. The portion of a tire between the tread and the bead. alphanumeric code assigned to a tire indicating the maximum speed at which a tire can operate.
Page 304 Tires need the correct amount of air pressure to operate effectively. A vehicle-specific Tire and Loading Information label is attached to the vehicle. This label shows the vehicle's original equipment tires and the correct inflation pressures for the tires when they are cold. The recommended cold tire inflation pressure, shown on the label, is the minimum amount of air...
Page 305 Use a good quality pocket-type gauge to check tire pressure. You cannot tell if the tires are properly inflated simply by looking at them. Radial tires may look properly inflated even when they are underinflated. Check the tire's inflation pressure when the tires are cold.
Page 306 When you end this high-speed driving, return the tires to the cold tire inflation pressure shown on the Tire and Loading Information label. The Tire Pressure Monitor System (TPMS) uses radio and sensor technology to check tire pressure levels. The TPMS sensors monitor the air pressure in your tires and transmit tire pressure readings to a receiver located in the vehicle.
Page 307 ensure that the replacement or alternate tires and wheels allow the TPMS to continue to function properly. additional information. for information regarding Part 15 of the Federal Communications Commission (FCC) rules and Industry Canada Standards RSS-210/220/310. This vehicle may have a Tire Pressure Monitor System (TPMS).
Page 308 Your vehicle's TPMS can warn you about a low tire pressure condition, but it does not replace normal tire maintenance. See , and The TPMS will not function properly if one or more of the TPMS sensors are missing or inoperable. When the system detects a malfunction, the low tire pressure warning light flashes for about one minute and...
Page 309 Replacement tires or wheels do not match your vehicle's original equipment tires or wheels. Tires and wheels other than those recommended for your vehicle could prevent the TPMS from functioning properly. See Operating electronic devices or being near facilities using radio wave frequencies similar to the TPMS could cause the TPMS sensors to malfunction.
Page 310 6. Press the SET/CLR button again to confirm the selection. The horn sounds twice to signal the receiver is in relearn mode and the TIRE LEARNING ACTIVE message displays on the DIC screen. 7. Start with the driver side front tire. 8.
Page 311: Tire Rotation
Tires should be rotated every 12 000 km (7,500 miles). See The purpose of a regular tire rotation is to achieve a uniform wear for all tires on the vehicle. This will ensure that the vehicle continues to perform most like it did when the tires were new.
Page 312 Make certain that all wheel nuts are properly tightened. See Wheel Nut Torque under Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after time. The wheel could come off and cause an accident.
Page 313 The rubber in tires age over time. This is also true for the spare tire, if the vehicle has one, even if it is not being used. Multiple conditions affect how fast this aging takes place, including temperatures, loading conditions, and inflation pressure maintenance.
Page 314 GM recommends replacing tires in sets of four. This is because uniform tread depth on all tires will help keep the vehicle performing most like it did when the tires were new. Replacing less than a full set of tires can affect the braking and handling performance of the vehicle.
Page 315 Vehicles that have a tire pressure monitoring system could give an inaccurate low pressure warning if non TPC Spec rated tires are installed on the vehicle. Non TPC Spec rated tires may give a low pressure warning that is higher or lower than the proper warning level you would get with TPC Spec rated tires.
Page 316 Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width. For example: The following information relates to the system developed by the United States National Highway Traffic Safety Administration (NHTSA), which grades tires by treadwear, traction, and temperature performance.
Page 317 The traction grades, from highest to lowest, are AA, A, B, and C. Those grades represent the tire's ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance.
Page 318 The tires and wheels on the vehicle were aligned and balanced carefully at the factory to give the longest tire life and best overall performance. Adjustments to wheel alignment and tire balancing will not be necessary on a regular basis. However, if there is unusual tire wear or the vehicle pulls to one side or the other, the alignment should be checked.
Page 319: Wheels
Replacing a wheel with a used one is dangerous. How it has been used or how far it has been driven may be unknown. It could fail suddenly and cause a crash. When replacing wheels, use a new GM original equipment wheel.
Page 320: If A Tire Goes Flat
It is unusual for a tire to blowout while you are driving, especially if you maintain the vehicle's tires properly. If air goes out of a tire, it is much more likely to leak out slowly. But if you should ever have a blowout, here are a few tips about what to expect and what to do: If a front tire fails, the flat tire...
Page 321 Changing a tire can be dangerous. The vehicle can slip off the jack and roll over or fall on you or other people. You and they could be badly injured or even killed. Find a level place to change the tire. To help prevent the vehicle from moving: 1.
Page 322 To access the spare tire and tools: 1. Open the trunk. 2. Remove the spare tire cover. 3. Turn the retainer nut counterclockwise and remove the spare tire. Place the spare tire next to the tire being changed. 4. The jack and tools are stored below the spare tire.
Page 323 5. Place the jack near the flat tire. 6. Put the compact spare tire near you. Getting under a vehicle when it is jacked up is dangerous. If the vehicle slips off the jack, you could be badly injured or killed. Never get under a vehicle when it is supported only by a jack.
Page 324 Place the jack notch, as shown. 10. Raise the vehicle by turning the jack handle clockwise. Raise the vehicle far enough off the ground so there is enough room for the road tire to clear the ground. 11. Remove all of the wheel nuts. 12.
Page 325 an emergency, use a cloth or a paper towel to do this; but be sure to use a scraper or wire brush later, if needed, to get all the rust or dirt off. See 13. Remove any rust or dirt from the wheel bolts, mounting surfaces, and spare wheel.
Page 326 17. Tighten the wheel nuts firmly in a crisscross sequence, as shown. 18. Lower the jack all the way and remove the jack from under the vehicle. 19. Tighten the wheel nuts firmly with the wheel wrench. When reinstalling the wheel cover or center cap on the full-size tire, tighten all five plastic caps hand snug with the aid of the wheel...
Page 327: Compact Spare Tire
4. Place the tire, lying flat, facing up in the spare tire well. 5. Turn the retainer nut clockwise to secure the tire. 6. Place the floor cover on the wheel. To store the compact spare tire, use the shorter mounting bolt. The compact spare is for temporary use only.
Page 328 Do not mix the compact spare tire or wheel with other wheels or tires. They will not fit. Keep the spare tire and its wheel together. For more information about the vehicle battery, see If the battery has run down, try to use another vehicle and some jumper cables to start your vehicle.
Page 329 The jump start positive (B) is located under a trim cover in the engine compartment on the driver side of the vehicle. These locations are used instead of a direct connection to the battery. 1. Check the other vehicle. It must have a 12-volt battery with a negative ground system.
Page 330 4. Turn the ignition to LOCK/OFF and switch off all lights and accessories in both vehicles, except the hazard warning flashers if needed. An electric fan can start up even when the engine is not running and can injure you. Keep hands, clothing and tools away from any underhood electric fan.
Page 331 5. Connect one end of the red positive (+) cable to the jump start positive (+) post (A). Use a remote positive (+) terminal if the vehicle has one. 6. Do not let the other end of the red positive (+) cable touch metal.
Page 332 A. Heavy, Unpainted Metal Engine Part or Remote Negative ( ) Terminal B. Good Battery or Remote Positive (+) and Remote Negative ( ) Terminals C. Dead Battery or Remote Positive (+) Terminal To disconnect the jumper cables from both vehicles: 1.
Page 333: Towing The Vehicle
Consult your dealer or a professional towing service if the disabled vehicle must be towed. To tow the vehicle behind another vehicle for recreational purposes, such as behind a motor home, see Recreational Vehicle Towing in this section. Recreational vehicle towing means towing the vehicle behind another vehicle, such as behind a motor home.
Page 334 Vehicles with the 2.0L engine and an automatic transmission should not be towed with all four wheels on the ground. When dinghy towing a vehicle with an automatic transmission, the vehicle should be run at the beginning of each day and at each RV fuel stop for about five minutes.
Page 335 The vehicle was not designed to be towed from the rear with all four wheels on the ground. Vehicles with front-wheel drive can be dolly towed from the front. Use the following procedure to dolly tow the vehicle from the front: 1.
Page 336 The vehicle cannot be dolly towed from the rear. Use only lukewarm or cold water, a soft cloth, and a car washing soap to clean exterior lamps and lenses. Follow instructions under Washing the Vehicle later in this section. Occasional waxing or mild polishing of the vehicle by hand may be necessary to remove residue from the paint finish.
Page 337 Bright metal parts should be cleaned regularly to keep their luster. Wash with water or use chrome polish on chrome or stainless steel trim, if necessary. Use special care with aluminum trim. To avoid damaging protective trim, never use auto or chrome polish, steam, or caustic soap to clean aluminum.
Page 338 The vehicle may have either aluminum or chrome-plated wheels. Keep the wheels clean using a soft, clean cloth with mild soap and water. Rinse with clean water. After rinsing thoroughly, dry with a soft, clean towel. A wax may then be applied.
Page 339 Use a stiff brush with tire cleaner to clean the tires. If the vehicle is damaged and requires sheet metal repair or replacement, make sure the body repair shop applies anti-corrosion material to parts repaired or replaced to restore corrosion protection.
Page 340 The interior will continue to look its best if it is cleaned often. Dust and dirt can accumulate on the upholstery and cause damage to the carpet, fabric, leather, and plastic surfaces. Stains should be removed quickly as extreme heat could cause them to set rapidly.
Page 341 Use a vacuum cleaner with a soft brush attachment to remove dust and loose dirt. A canister vacuum with rotating brushes in the nozzle may only be used on floor carpet and carpeted floor mats. For soils, always try to remove them first with plain water or club soda.
Page 342 Leather, and lighter colored leather in particular, will need more frequent cleaning to prevent the buildup of dust, dirt, and colors transferred from other items so that these do not become permanent stains. To remove dust, a soft cloth dampened with water can be used. If a more thorough cleaning is necessary, a soft cloth dampened with a mild soap solution can be...
Page 343 If a floor mat is the wrong size or is not properly installed, it can interfere with the accelerator pedal and/or brake pedal. Interference with the pedals can cause unintended acceleration and/or increased stopping distance which can cause a crash and injury.

Buick 2011 Regal Owner's Manual

Instruments and Controls

System

Introduction

Radio

Audio Players

Phone

Table of Contents

Quick Links

Chapters

Related Manuals for Buick 2011 Regal

Summary of Contents for Buick 2011 Regal

Table of Contents