Page 109: Table Of Contents
Instruments and Controls Controls Steering Wheel Adjustment . . . 5-2 Steering Wheel Controls ..5-2 Horn ......5-2 Windshield Wiper/Washer .
Page 110: Instruments And Controls
Instruments and Controls Controls Steering Wheel Adjustment To adjust the steering wheel: 1. Pull the lever down. 2. Move the steering wheel up, down, forward, and backward. 3. Pull the lever up to lock the steering wheel in place. Do not adjust the steering wheel while driving.
Page 111: Windshield Wiper/Washer
Windshield Wiper/Washer The windshield wiper lever is on the side of the steering column. With the ignition in ACC/ ACCESSORY or ON/RUN, move the windshield wiper lever to select the wiper speed. 2: Use for fast wipes. 1: Use for slow wipes. (Adjustable Interval Wipes): Turn the band up for more frequent wipes or down for less frequent...
Page 112: Compass
Instruments and Controls Windshield Washer Pull the windshield wiper lever toward you to spray windshield washer fluid and activate the wipers. The wipers will continue until the lever is released or the maximum wash time is reached. When the windshield wiper lever is released, additional wipes may occur depending on how long the windshield washer had been...
Page 113: Clock
Clock The infotainment system controls are used to access the time and date settings through the menu system. See for information about how to use the menu system. Setting the Time and Date 1. Press the CONFIG button and select Time and Date Settings. 2.
Page 114 Instruments and Controls Certain electrical accessories may not be compatible with the accessory power outlets and could overload vehicle or adapter fuses. If there is a problem, see your dealer. When adding electrical equipment, be sure to follow the installation instructions included with the equipment.
Page 115: Warning Lights, Gauges, And Indicators
power outlet at the maximum load of 150 watts may cause the outlet to overheat and automatically shut down. The power restarts when equipment that operates within the limit is plugged into the outlet and a system fault is not detected. The power outlet is not designed for the following equipment, and may not work properly if any of the...
Page 116: Instrument Cluster
Instruments and Controls Instrument Cluster English Automatic Transmission Shown, Manual and Metric Similar...
Page 117: Speedometer
Speedometer The speedometer shows the vehicle's speed in either kilometers per hour (km/h) or miles per hour (mph). Odometer The odometer shows how far the vehicle has been driven, in either kilometers or miles. This vehicle has a tamper resistant odometer.
Page 118: Engine Coolant Temperature
5-10 Instruments and Controls Here are four things that some owners ask about. None of these show a problem with the fuel gauge: At the service station, the fuel pump shuts off before the gauge reads full. It takes a little more or less fuel to fill up than the gauge indicated.
Page 119: Safety Belt Reminders
Safety Belt Reminders Driver Safety Belt Reminder Light There is a driver safety belt reminder light on the instrument panel cluster. When the engine is started this light begins to flash and a chime comes on for several seconds to remind the driver to fasten their safety belt.
Page 120: Passenger Airbag Status
5-12 Instruments and Controls The airbag readiness light comes on and stays on for several seconds when the vehicle is started. Then the light goes out. WARNING If the airbag readiness light stays on after the vehicle is started or comes on while driving, it means the airbag system might not be working properly.
Page 121: Charging System Light
If, after several seconds, both status indicator lights remain on, or if there are no lights at all, there may be a problem with the lights or the passenger sensing system. See your dealer for service. WARNING If the airbag readiness light ever comes on and stays on, it means that something may be wrong with the airbag system.
Page 122 5-14 Instruments and Controls Malfunctions often are indicated by the system before any problem is apparent. Heeding the light can prevent more serious damage to the vehicle. This system assists the service technician in correctly diagnosing any malfunction. If the vehicle is continually driven with this light on, the emission controls might not work as well, the vehicle fuel...
Page 123 Check that the electrical system is not wet. The system could be wet if the vehicle was driven through a deep puddle of water. The condition is usually corrected when the electrical system dries out. A few driving trips should turn the light off. Check that good quality fuel is used.
Page 124: Brake System Warning
5-16 Instruments and Controls Brake System Warning Light The vehicle brake system consists of two hydraulic circuits. If one circuit is not working, the remaining circuit can still work to stop the vehicle. For normal braking performance, both circuits need to be working. If the warning light comes on, there is a brake problem.
Page 125: Ultrasonic Parking Sensor
The brake warning light should come on briefly when the ignition is placed in ON/RUN. If it does not come on, have the vehicle serviced by your dealer. If this light comes on, there is a problem with a system on the vehicle that is causing the parking brake system to work at a reduced level.
Page 126: Traction Off Light
5-18 Instruments and Controls Traction Off Light This light comes on briefly while starting the engine. If it does not, have the vehicle serviced by your dealer. If the system is working normally, the indicator light then goes off. The traction off light comes on when the Traction Control System (TCS) has been turned off or if there is a problem with the TCS.
Page 127: Tire Pressure Light
If the light is on and not flashing, the TCS and potentially the StabiliTrak system have been disabled. Check the DIC messages to determine which feature(s) is no longer functioning and whether it is because of the driver turning off the feature(s), or because the system is not working properly and the vehicle requires service.
Page 128: Engine Oil Pressure Light
5-20 Instruments and Controls Engine Oil Pressure Light WARNING Do not keep driving if the oil pressure is low. The engine can become so hot that it catches fire. Someone could be burned. Check the oil as soon as possible and have the vehicle serviced.
Page 129: Security Light
Security Light The immobilizer light should come on briefly as the engine is started. If it does not come on, have the vehicle serviced by your dealer. If the system is working normally, the indicator light turns off. This light comes on when the ignition is turned from LOCK/OFF to ON/RUN and stays on if the vehicle is immobilized.
Page 130: Cruise Control Light
5-22 Instruments and Controls Cruise Control Light The cruise control light is white whenever the cruise control is set, and turns green when the cruise control is active. The light turns off when the cruise control is turned off. See for more information.
Page 131 DIC Buttons MENU: Press to get to the Trip/ Fuel Menu and the Vehicle Information Menu. (Thumbwheel): Use to scroll through the items in each menu. A small marker will move across the bottom of the page as you scroll through the items.
Page 132 5-24 Instruments and Controls The instantaneous fuel economy reflects only the current fuel economy and changes frequently as driving conditions change. Unlike average economy, this display cannot be reset. Average Vehicle Speed This display shows the average speed of the vehicle in kilometers per hour (km/h) or miles per hour (mph).
Page 133: Vehicle Messages
Tire Pressure The display will show a vehicle with the approximate pressures of all four tires. Tire pressure is displayed in either kilopascal (kPa) or pounds per square inch (psi). See for more information. Remaining Oil Life This display shows an estimate of the oil's remaining useful life.
Page 134: Battery Voltage And Charging
5-26 Instruments and Controls Battery Voltage and Charging Messages BATTERY SAVER ACTIVE This message displays when the vehicle has detected that the battery voltage is dropping beyond a reasonable point. The battery saver system starts reducing certain features of the vehicle that you may be able to notice.
Page 135: Door Ajar Messages
Door Ajar Messages DRIVER DOOR OPEN This message will display when the driver door is open. Close the door completely. HOOD OPEN This message will display when the hood is open. Close the hood completely. LEFT REAR DOOR OPEN This message will display when the driver side rear door is open.
Page 136: Engine Oil Messages
5-28 Instruments and Controls HIGH COOLANT TEMPERATURE This message displays if the coolant temperature is hot. See Engine Oil Messages CHANGE ENGINE OIL SOON This message displays when the engine oil needs to be changed. When you change the engine oil, be sure to reset the Oil Life System.
Page 137: Key And Lock Messages
Key and Lock Messages REPLACE BATTERY IN REMOTE KEY This message displays when the battery in the Remote Keyless Entry (RKE) transmitter needs to be replaced. Object Detection System Messages PARK ASSIST OFF This message is displayed when the park assist system has been turned off.
Page 138: Tire Messages
5-30 Instruments and Controls Tire Messages TIRE PRESSURE LOW ADD AIR TO TIRE On vehicles with the Tire Pressure Monitor System (TPMS), this message displays when the pressure in one or more of the vehicle's tires is low. The low tire pressure warning light will also come on.
Page 139: Window Messages
Window Messages OPEN, THEN CLOSE DRIVER WINDOW This message is displayed when the window needs to be reprogrammed. If the vehicle's battery has been recharged or disconnected, you will need to reprogram each front window for the express-up feature to work. See for more information.
Page 140 5-32 Instruments and Controls Climate and Air Quality Select the Climate and Air Quality menu and the following will be displayed: Auto Fan Speed Air Conditioning Mode Auto Area Zone Temp Auto Defog Auto Rear Defog Auto Fan Speed This allows selection of the automatic fan speed to run lower or higher than normal.
Page 141 Auto Rear Defog This allows the auto rear defog to be turned on or off. This feature will automatically turn on the rear defogger when it is cold outside. Press the knob when Auto Rear Defog is highlighted to select On or Off.
Page 142 5-34 Instruments and Controls Power Door Locks Select Power Door Locks and the following will be displayed: Unlocked Door Anti Lock Out Auto Door Unlock Delayed Door Lock Unlocked Door Anti Lock Out When on, this feature will keep the driver door from locking when the door is open.
Page 143 Remote Lock Feedback This allows selection of what type of feedback is given when locking the vehicle with the RKE transmitter. Press the knob when Remote Lock Feedback is highlighted. Turn the knob to select Lights and Horn, Lights Only, Horn Only, or Off.
Page 144 5-36 Instruments and Controls NOTES...
Page 151: Infotainment System
Infotainment System Introduction Infotainment ....7-1 Theft-Deterrent Feature ..7-2 Overview ..... . 7-2 Operation .
Page 152: Theft-Deterrent Feature
Infotainment System for more information. Navigation System For vehicles with a navigation system, see the separate Navigation System Manual. Theft-Deterrent Feature The theft-deterrent feature works by learning a portion of the Vehicle Identification Number (VIN) to the infotainment system. The infotainment system does not operate if it is stolen or moved to a different vehicle.
Page 153 Radio: Seeks the previous station. CD: Select the previous track or rewinds within a track. D. CONFIG Opens the Settings menu. Radio: Seeks the next station. CD: Selects the next track or fast forwards within a track. Turns the system on or off and adjusts the volume.
Page 154: Operation
Infotainment System Operation Controls The infotainment system is operated by using the pushbuttons, multifunction knobs, menus shown on the display, and steering wheel controls, if equipped. Turning the System On or Off (Volume/Power): Press to turn the system on and off. Automatic Switch Off If the infotainment system has been turned on after the ignition is turned...
Page 155 Submenus An arrow on the right hand edge of the menu indicates that it has a submenu with other options. Activating a Setting 1. Turn the knob to highlight the setting. 2. Press the knob to activate the setting. Setting a Value 1.
Page 156 Infotainment System 3. Press and hold the knob until the value changes to 0. Press the BACK button to go back to the Tone Settings menu. Adjusting the Treble, Midrange, and Bass 1. Press the TONE button. 2. Select Treble, Midrange, or Bass.
Page 157: Radio
5. Press the BACK button to go back to the System Configuration menu. Maximum Startup Volume The maximum volume played when the radio is first turned on can be set. 1. Press the CONFIG button. 2. Select Radio Settings. 3. Select Maximum Startup Volume.
Page 158 Infotainment System AS 1/2: Press to open the autostore list and select autostore pages. RDS (Radio Data System) The radio may have RDS. The RDS feature is available for use only on FM stations that broadcast RDS information. This feature only works when the information from the radio station is available.
Page 159 To search for a programming type determined by station: 1. Press the knob. 2. Select FM Category List. A list of all programming types available displays. 3. Select the programming type. A list of stations that transmit programming of the selected type displays.
Page 160: Satellite Radio
7-10 Infotainment System Satellite Radio Vehicles with an XM Satellite Radio tuner and a valid XM Satellite Radio subscription can receive XM programming. XM Satellite Radio Service XM is a satellite radio service based in the 48 contiguous United States and 10 Canadian provinces.
Page 161 Selecting an XM Channel XM channels can be selected by station lists or category lists. Selecting a Channel by Station List XM channels can be selected by using , or the knob. To select an XM channel using , do one of the following: Press and release to go to the previous or next channel.
Page 162 7-12 Infotainment System XM Messages XL (Explicit Language Channels): These channels, or any others, can be blocked by request, by calling 1-800-929-2100 in the U.S. and 1-877-438-9677 in Canada. XM Updating: The encryption code in the receiver is being updated. No action is required.
Page 163: Radio Reception
XM Not Available: If this message does not clear within a short period of time, the receiver could have a fault. Consult with your dealer. Radio Reception Frequency interference and static can occur during normal radio reception if items such as cellular phone chargers, vehicle convenience accessories, and external electronic devices are...
Page 164: Satellite Radio Antenna
7-14 Infotainment System If a cellular telephone antenna needs to be attached to the glass, make sure that the grid lines for the AM-FM antenna are not damaged. There is enough space between the grid lines to attach a cellular telephone antenna without interfering with radio reception.
Page 165 If the bottom surface of a disc is dirty, take a soft lint free cloth, or dampen a clean soft cloth in a mild neutral detergent solution mixed with water, and clean it. Wipe the disc from the center to the outer edge.
Page 166 7-16 Infotainment System Selecting a CD Track Using the control buttons: Press the button to select the previous or next track. Turn the knob. Using the CD Menu: 1. Press the knob. 2. Select Tracks list. 3. Select the track. Playing Tracks in Random Order Press the knob and then set...
Page 167: Auxiliary Devices
Auxiliary Devices This vehicle may have a 3.5 mm (1/8 in) auxiliary input jack and a USB port, located in the center console. Some portable audio ® devices such as iPods , MP3 players, and USB storage devices can be connected to the vehicle using a 3.5 mm (1/8 in) cable or a USB cable.
Page 168 7-18 Infotainment System Albums Song Titles Podcasts Genres Audiobooks Composers To search for tracks: 1. Press the knob. 2. Select Search. 3. Select: Playlists, Artists, Albums, Song Titles, Podcasts, Genres, Audiobooks, or Composers. 4. Select the track. Shuffle Press the knob and set Shuffle Songs (Random) to On or Off, then press the BACK button to...
Page 169 Repeat Off: Starts playing from the beginning of the current track after the last track finishes. Connecting and Controlling a USB Drive The infotainment system can only play back .mp3 and .wma files from a USB drive. Only the first 2,500 songs are recognized on the device.
Page 170: Phone
7-20 Infotainment System Phone Bluetooth (Overview) Vehicles with a Bluetooth system can use a Bluetooth capable cell phone with a Hands Free Profile to make and receive phone calls. The infotainment system and voice recognition are used to control the system.
Page 171: Bluetooth
for Federal Communications Commission (FCC) rules and Industry Canada Standards. Bluetooth (Infotainment Controls) For information about how to navigate the menu system using the infotainment controls, see Pairing A Bluetooth enabled cell phone must be paired to the Bluetooth system first and then connected to the vehicle before it can be used.
Page 172 7-22 Infotainment System Locate the device named General Motors or Your Vehicle in the list on the cell phone and follow the instructions on the cell phone to enter the four digit PIN provided by the system. 6. The system prompts for a name for the phone and confirms the name provided.
Page 173: Bluetooth
Accepting a Call Turn the knob to Answer and press the knob. Declining a Call Turn the knob to Decline and press the knob. Switching Between Calls (Call Waiting Calls Only) To switch between calls: 1. Press the knob. 2. Select Switch Call from the menu.
Page 174 7-24 Infotainment System Calling, if available. Refer to the OnStar Owner's Guide for more information. The pairing process can be started by using the voice recognition system or the controls on the infotainment system. Pairing information: Up to five cell phones can be paired to the Bluetooth system.
Page 175 Listing All Paired and Connected Phones 1. Press For vehicles without a navigation system, the system responds Ready, followed by a tone. For vehicles with a navigation system, the system responds with a tone. After the tone, say Hands Free. The system responds Ready, followed by a tone.
Page 176 7-26 Infotainment System 3. Say Change phone. The system responds Please wait while I search for other phones. If another phone is found, the response will be <Phone name> is now connected. If another phone is not found, the original phone remains connected.
Page 177 the number is stored, the system returns to the main menu. Using the Digit Store Command The digit store command allows a phone number to be stored by entering the digits individually. 1. Press For vehicles without a navigation system, the system responds Ready, followed by a tone.
Page 178 7-28 Infotainment System 2. Say Directory. The system responds Directory and lists all stored name tags. The system returns to the main menu when the list is complete. Deleting Name Tags The system uses the following commands to delete name tags: Delete Delete all name tags Using the Delete Command...
Page 179 2. Say Delete all name tags. The system responds You are about to delete all name tags stored in your phone directory and your route destination directory. Are you sure you want to do this? Please say yes or no. Say Yes to delete all name tags.
Page 180 7-30 Infotainment System 2. Say Digit Dial. The system responds Digit dial using <phone name>, please say the first digit to dial, followed by a tone. 3. Say the digits to be dialed one at a time. The system repeats back the digit it heard followed by a tone.
Page 181 Hands Free. The system responds Ready, followed by a tone. 2. After the tone, say Re dial. The system responds Re dial using <phone name> and dials the last number called from the connected Bluetooth phone. Once connected, the person called will be heard through the audio speakers.
Page 182 7-32 Infotainment System To Cancel Mute 1. Press . The system responds Ready, followed by a tone. 2. After the tone, say Mute Call. The system responds Resuming call. Transferring a Call Audio can be transferred between the in vehicle Bluetooth system and the cell phone.
Page 183 3. Say Voice. The system responds OK, accessing <phone name>. The cell phone's normal prompt messages will go through their cycle according to the phone's operating instructions. Dual Tone Multi-Frequency (DTMF) Tones The in vehicle Bluetooth system can send numbers and the numbers stored as name tags during a call.
Page 184 7-34 Infotainment System NOTES...
Page 241 General Information ..10-2 California Proposition 65 Warning ....10-3 California Perchlorate Materials Requirements .
Page 242 Tires ......10-42 Winter Tires ....10-43 Tire Sidewall Labeling .
Page 243 Most motor vehicles, including this one, contain and/or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Engine exhaust, many parts and systems, many fluids, and some component wear by-products contain and/or emit these chemicals.
Page 244 You can be injured and the vehicle could be damaged if you try to do service work on a vehicle without knowing enough about it. Be sure you have sufficient knowledge, experience, the proper replacement parts, and tools before attempting any vehicle maintenance task.
Page 245 To open the hood: 1. Pull up on the hood release handle with this symbol on it. It is located inside the vehicle to the left of the steering column. 2. Go to the front of the vehicle and move the secondary hood release handle to the right.
Page 247 B. Engine Cover. C. Engine Oil Dipstick. See D. Engine Oil Fill Cap. See E. Transmission Fluid Cap and Dipstick. See Power Steering Fluid Reservoir and Cap. See G. Brake Master Cylinder and Hydraulic Clutch Reservoir (if equipped with manual transmission).
Page 249 B. Engine Cover. C. Engine Oil Fill Cap. See D. Engine Oil Dipstick. See E. Transmission Fluid Cap and Dipstick. See Brake Master Cylinder Reservoir. See G. Power Steering Fluid Reservoir and Cap. See H. Engine Coolant Reservoir and Pressure Cap. See Battery Cover.
Page 250 2. Pull out the dipstick and clean it with a paper towel or cloth, then push it back in all the way. Remove it again, keeping the tip down, and check the level. If the oil is below the cross-hatched area at the tip of the dipstick, add 1 L (1 qt) of the recommended oil and then recheck the level.
Page 251 Use of Substitute Engine Oils if dexos is unavailable: In the event that dexos approved engine oil is not available at an oil change or for maintaining proper oil level, you may use substitute engine oil displaying the API Starburst symbol and of SAE 5W-30 viscosity grade.
Page 252 Maintaining the proper oil level is very important. However, if you use a substitute oil for any reason, we recommend that you perform a complete oil change back to dexos as soon as possible to protect the engine and maintain the engine's peak performance.
Page 253 Used engine oil contains certain elements that can be unhealthy for your skin and could even cause cancer. Do not let used oil stay on your skin for very long. Clean your skin and nails with soap and water, or a good hand cleaner. Wash or properly dispose of clothing or rags containing used engine oil.
Page 254 2. Press the DIC menu button on the turn signal lever to enter the Vehicle Information Menu. Use the thumbwheel to scroll through the menu items until you reach REMAINING OIL LIFE. 3. Press the SET/CLR button to reset the oil life at 100%. 4.
Page 255 The brake/hydraulic clutch fluid reservoir cap has this symbol on it. The common hydraulic clutch and brake master cylinder fluid reservoir is filled with either DOT 3 or DOT 4 brake fluid as indicated on the reservoir cap. See for reservoir location. Visually check the brake/clutch fluid reservoir to make sure the fluid level is at the MIN (minimum) line on the...
Page 256 3. Disconnect the electrical connector (A). 4. Remove the screws (C) on top of the engine air cleaner/filter housing. 5. Lift the filter cover housing away from the engine. 6. Pull out the filter. 7. Inspect or replace the engine air cleaner/filter.
Page 257 The cooling system allows the engine to maintain the correct working temperature. When it is safe to lift the hood: A. Electric Engine Cooling Fans B. Coolant Surge Tank and Pressure Cap A. Electric Engine Cooling Fans B. Coolant Surge Tank and Pressure Cap An electric engine cooling fan under the hood can start up even...
Page 258 The cooling system in the vehicle is ® filled with DEX-COOL engine coolant. This coolant is designed to remain in the vehicle for 5 years or 240 000 km (150,000 miles), whichever occurs first. The following explains the cooling system and how to check and add coolant when it is low.
Page 259 Never dispose of engine coolant by putting it in the trash, pouring it on the ground, or into sewers, streams, or bodies of water. Have the coolant changed by an authorized service center, familiar with legal requirements regarding used coolant disposal. This will help protect the environment and your health.
Page 260 If no problem is found, check to see if coolant is visible in the coolant surge tank. If coolant is visible but the coolant level is not at the indicated level mark, add a 50/50 mixture of clean, drinkable water and DEX-COOL coolant at the coolant surge tank, but be sure the cooling system, including the coolant surge tank pressure cap, is...
Page 261 1. Remove the coolant surge tank pressure cap when the cooling system, including the coolant surge tank pressure cap and upper radiator hose, is no longer hot. Turn the pressure cap slowly counterclockwise about one-quarter of a turn. If you hear a hiss, wait for that to stop.
Page 262 If it is decided not to lift the hood when this warning appears, but instead get service help right away, If it is decided to lift the hood, make sure the vehicle is parked on a level surface. Then check to see if the engine cooling fans are running.
Page 263 If the temperature overheat gauge is no longer in the overheat zone or an overheat warning no longer displays, the vehicle can be driven. Continue to drive the vehicle slow for about 10 minutes. Keep a safe vehicle distance from the car in front of you.
Page 264 5. Remove the cap again and look at the fluid level on the dipstick. The fluid level should be between the MIN (Minimum) and MAX (Maximum) marks when the engine is cold, and at the MAX mark when the engine is hot. If the fluid is at the MIN mark when the engine is cold or hot, power steering fluid should be added.
Page 265 This vehicle has disc brakes. Disc brake pads have built-in wear indicators that make a high-pitched warning sound when the brake pads are worn and new pads are needed. The sound can come and go or be heard all the time the vehicle is moving, except when applying the brake pedal firmly.
Page 266 The brake master cylinder and, on manual transmission vehicles, the clutch hydraulic system use the same reservoir. See for the location of the reservoir. The reservoir is filled with with either DOT 3 or DOT 4 brake fluid as indicated on the reservoir cap.
Page 267 If the vehicle has DOT 4 brake fluid, as indicated on the reservoir cap, use only new DOT 4 brake fluid from a sealed container. It is recommended that the brake/clutch hydraulic system be flushed and refilled with new DOT 4 fluid at a regular maintenance service every two years.
Page 268 Extended Storage: Remove the black, negative ( ) cable from the battery or use a battery trickle charger. When you are doing this inspection, the vehicle could move suddenly. If the vehicle moves, you or others could be injured. 1. Before starting this check, be sure there is enough room around the vehicle.
Page 269 shift lever out of P (Park) with normal effort. If the shift lever moves out of P (Park), contact your dealer for service. While parked, and with the parking brake set, try to turn the ignition to LOCK/OFF in each shift lever position.
Page 270 Windshield wiper blades should be inspected for wear or cracking. See for more information. It is a good idea to clean or replace the wiper blade assembly on a regular basis or when worn. For proper windshield wiper blade length and type, see To replace the wiper blade: 1.
Page 271 For the proper type of replacement bulbs, see For any bulb changing procedure not listed in this section, contact your dealer. Halogen bulbs have pressurized gas inside and can burst if you drop or scratch the bulb. You or others could be injured. Be sure to read and follow the instructions on the bulb package.
Page 272 2. Remove the outside cap for the low-beam headlamp/DRL bulb replacement from the back of the headlamp assembly. 3. Remove the inside cap for the high-beam headlamp bulb replacement from the back of the headlamp assembly. 4. Disconnect the electrical connector.
Page 273 A. Taillamp/Sidemarker Lamp B. Taillamp C. Stop/Turn Signal Lamp D. Back-up Lamp To replace any one of these bulbs: 1. Open the trunk. See 2. Remove the taillamp assembly access panel. 3. Remove the two nuts that secure the taillamp assembly. 4.
Page 274 To replace one of these bulbs: 1. Push the release tab (A) toward the lamp assembly. 2. Pull the lamp assembly down to remove. A. Bulb Socket B. Bulb C. Lamp Assembly 3. Turn the bulb socket (A) counterclockwise to remove it from the lamp assembly (C).
Page 275 Stop Lamp/Turn 3157 K Signal Lamp Taillamp/ 3157 K Sidemarker Lamp For replacement bulbs not listed here, contact your dealer. The vehicle has fuses and circuit breakers to protect against an electrical system overload. When the current electrical load is too heavy, the circuit breaker opens and closes, protecting the circuit until the current load returns to...
Page 276 The wiring circuits in the vehicle are protected from short circuits by a combination of fuses and circuit breakers. This greatly reduces the chance of damage caused by electrical problems. To check a fuse, look at the silver-colored band inside the fuse. If the band is broken or melted, replace the fuse.
Page 277 Transmission Control Module Engine Control Module Not Used Not Used Ignition, Transmission Control Module, Engine Control Module Windshield Wiper Not Used Fuel Injection, Ignition System Even Fuel Injection, Ignition System Odd Engine Control Module Oxygen Sensor Starter Fuel System Control Module Secondary Air Induction...
Page 278 Vacuum Pump Ignition, Airbag Not Used Not Used Not Used Rear Power Windows Antilock Brake System Valve Variable Effort Steering Front Power Windows Power Outlets Antilock Brake System Pump Electric Parking Brake Heated Rear Window Left Hand Seat Lumbar Right Hand Seat Lumbar Not Used Body Control...
Page 279 Ignition, Inside Rearview Mirror Not Used Power Windows Windshield Washer Not Used Not Used Secondary Air Induction Heated Mirrors Not Used Canister Vent Solenoid Not Used Not Used Not Used Not Used Fuel System Control Module Not Used Battery Sensor Not Used Not Used Not Used...
Page 280 The instrument panel fuse block is located in the instrument panel, on the driver side of the vehicle. To access the fuses, open the storage compartment. Press in on the sides of the compartment to release it from the instrument panel. Pull the door toward you to release it from the hinge.
Page 281 Body Control Module 4 Body Control Module 8 Front Heater Ventilation Air Conditioning/Blower Right Hand Power Front Seat Left Hand Power Front Seat Diagnostic Link Connector Airbag Trunk Release Heater Ventilation Air Conditioning Controller Service Fuse, Logistic Relay Not Used Automatic Occupant Sensing Instrument Panel...
Page 282 Every new GM vehicle has high-quality tires made by a leading tire manufacturer. See the warranty manual for information regarding the tire warranty and where to get service. For additional information refer to the tire manufacturer. Poorly maintained and improperly used tires are dangerous.
Page 283 Consider installing winter tires on the vehicle if frequent driving on snow or ice covered roads is expected. All season tires provide good overall performance on most surfaces, but they may not offer the traction or the same level of performance as winter tires on snow or ice covered roads.
Page 284 Original equipment tires designed to GM's specific tire performance criteria have a TPC specification code molded onto the sidewall. GM's TPC specifications meet or exceed all federal safety guidelines. Department of Transportation (DOT) code indicates that the tire is in compliance with the U.S.
Page 285 compact spare tire, see The letters and numbers following the DOT (Department of Transportation) code are the Tire Identification Number (TIN). The TIN shows the manufacturer and plant code, tire size, and date the tire was manufactured. The TIN is molded onto both sides of the tire, although only one side may have the date of manufacture.
Page 286 A two digit number that indicates the tire height to width measurements. For example, if the tire size aspect ratio is 60, as shown in item C of the illustration, it would mean that the tire's sidewall is 60 percent as high as it is wide. letter code is used to indicate the type of ply construction in the tire.
Page 287 maximum capacity of fuel, oil, and coolant, but without passengers and cargo. A code molded into the sidewall of a tire signifying that the tire is in compliance with the U.S. Department of Transportation (DOT) Motor Vehicle Safety Standards. The DOT code includes the Tire Identification Number (TIN), an alphanumeric designator which can also...
Page 288 model name molding that is higher or deeper than the same moldings on the other sidewall of the tire. tire used on passenger cars and some light duty trucks and multipurpose vehicles. Vehicle manufacturer's recommended tire inflation pressure as shown on the tire placard.
Page 289 recommended inflation pressure. See Tire and Loading Information Label under Tires need the correct amount of air pressure to operate effectively. The Tire and Loading Information label on the vehicle indicates the original equipment tires and the correct cold tire inflation pressures.
Page 290 Remove the valve cap from the tire valve stem. Press the tire gauge firmly onto the valve to get a pressure measurement. If the cold tire inflation pressure matches the recommended pressure on the Tire and Loading Information label, no further adjustment is necessary.
Page 291 The Tire Pressure Monitor System (TPMS) uses radio and sensor technology to check tire pressure levels. The TPMS sensors monitor the air pressure in your tires and transmit tire pressure readings to a receiver located in the vehicle. Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended...
Page 292 for information regarding Part 15 of the Federal Communications Commission (FCC) rules and Industry Canada Standards RSS-210/220/310. This vehicle may have a Tire Pressure Monitor System (TPMS). The TPMS is designed to warn the driver when a low tire pressure condition exists.
Page 293 The TPMS will not function properly if one or more of the TPMS sensors are missing or inoperable. When the system detects a malfunction, the low tire pressure warning light flashes for about one minute and then stays on for the remainder of the ignition cycle.
Page 294 Each TPMS sensor has a unique identification code. The identification code needs to be matched to a new tire/wheel position after rotating the vehicle s tires or replacing one or more of the TPMS sensors. Also, the TPMS sensor matching process should be performed after replacing a spare tire with a road tire containing the TPMS sensor.
Page 295 12. Turn the ignition to LOCK/OFF. 13. Set all four tires to the recommended air pressure level as indicated on the Tire and Loading Information label. We recommend that the tires, including the spare tire, if the vehicle has one, be inspected for signs of wear or damage at least once a month.
Page 296 Reset the Tire Pressure Monitor System. See Make certain that all wheel nuts are properly tightened. See Wheel Nut Torque under Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after time.
Page 297 The rubber in tires ages over time. This also applies for the spare tire, if the vehicle has one, even if it is never used. Multiple conditions including temperatures, loading conditions, and inflation pressure maintenance affect how fast aging takes place. Tires will typically need to be replaced due to wear before they may need to be replaced due to age.
Page 298 Braking and handling performance may be adversely affected if all the tires are not replaced at the same time. See for information on proper tire rotation. Tires could explode during improper service. Attempting to mount or dismount a tire could cause injury or death.
Page 299 If wheels or tires are installed that are a different size than the original equipment wheels and tires, vehicle performance, including its braking, ride and handling characteristics, stability, and resistance to rollover may be affected. If the vehicle has electronic systems such as antilock brakes, rollover airbags, traction control, and electronic stability control, the performance of these...
Page 300 All Passenger Car Tires Must Conform to Federal Safety Requirements In Addition To These Grades. The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and a half (1½) times as well on the...
Page 301 The tires and wheels were aligned and balanced at the factory to provide the longest tire life and best overall performance. Adjustments to wheel alignment and tire balancing will not be necessary on a regular basis. However, check the alignment if there is unusual tire wear or if the vehicle is pulling to one side or the other.
Page 302 Do not use tire chains. There is not enough clearance. Tire chains used on a vehicle without the proper amount of clearance can cause damage to the brakes, suspension, or other vehicle parts. The area damaged by the tire chains could cause loss of control and a crash.
Page 303 Lifting a vehicle and getting under it to do maintenance or repairs is dangerous without the appropriate safety equipment and training. If a jack is provided with the vehicle, it is designed only for changing a flat tire. If it is used for anything else, you or others could be badly injured or killed if the vehicle slips off the jack.
Page 304 3. Turn the retainer nut counterclockwise and remove the spare tire. Place the spare tire next to the tire being changed. 4. The jack and tools are stored below the spare tire. Remove them from their container and place them near the tire being changed.
Page 305 6. Put the compact spare tire near you. Getting under a vehicle when it is jacked up is dangerous. If the vehicle slips off the jack, you could be badly injured or killed. Never get under a vehicle when it is supported only by a jack.
Page 306 Place the jack notch, as shown. 10. Raise the vehicle by turning the jack handle clockwise. Raise the vehicle far enough off the ground so there is enough room for the road tire to clear the ground. 11. Remove all of the wheel nuts. 12.
Page 307 Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after time. The wheel could come off and cause an accident. When changing a wheel, remove any rust or dirt from places where the wheel attaches to the vehicle.
Page 308 Wheel nuts that are improperly or incorrectly tightened can cause the wheels to become loose or come off. The wheel nuts should be tightened with a torque wrench to the proper torque specification after replacing. Follow the torque specification supplied by the aftermarket manufacturer when using accessory locking wheel nuts.
Page 309 2. Slide the shorter bolt to remove it from the floor and insert the longer one. 3. Replace the jack and tools in their original storage location. 4. Place the tire, lying flat, facing up in the spare tire well. 5.
Page 310 Do not use the compact spare on other vehicles. Do not mix the compact spare tire or wheel with other wheels or tires. They will not fit. Keep the spare tire and its wheel together. For more information about the vehicle battery, see If the battery has run down, try to use another vehicle and some...
Page 311 The jump start positive (B) is located under a trim cover in the engine compartment on the driver side of the vehicle. These locations are used instead of a direct connection to the battery. 1. Check the other vehicle. It must have a 12-volt battery with a negative ground system.
Page 312 An electric fan can start up even when the engine is not running and can injure you. Keep hands, clothing and tools away from any underhood electric fan. Using a match near a battery can cause battery gas to explode. People have been hurt doing this, and some have been blinded.
Page 313 7. Connect one end of the black negative ( ) cable to the negative ( ) terminal of the good battery (C). Use a remote negative ( ) terminal if the vehicle has one. Do not let the other end touch anything until the next step.
Page 314 To disconnect the jumper cables from both vehicles: 1. Disconnect the black negative ( ) cable from the vehicle that had the dead battery. 2. Disconnect the black negative ( ) cable from the vehicle with the good battery. 3. Disconnect the red positive (+) cable from the vehicle with the good battery.
Page 315 Is the proper towing equipment going to be used? See your dealer or trailering professional for additional advice and equipment recommendations. Is the vehicle ready to be towed? Just as preparing the vehicle for a long trip, make sure the vehicle is prepared to be towed.
Page 316 The vehicle was not designed to be towed from the rear with all four wheels on the ground. Vehicles with front-wheel drive can be dolly towed from the front. Use the following procedure to dolly tow the vehicle from the front: 1.
Page 317 The vehicle cannot be dolly towed from the rear. Use only lukewarm or cold water, a soft cloth, and a car washing soap to clean exterior lamps and lenses. Follow instructions under Washing the Vehicle later in this section. Occasional waxing or mild polishing of the vehicle by hand may be necessary to remove residue from the paint finish.
Page 318 Bright metal parts should be cleaned regularly to keep their luster. Wash with water or use chrome polish on chrome or stainless steel trim, if necessary. Use special care with aluminum trim. To avoid damaging protective trim, never use auto or chrome polish, steam, or caustic soap to clean aluminum.
Page 319 The vehicle may have either aluminum or chrome-plated wheels. Keep the wheels clean using a soft, clean cloth with mild soap and water. Rinse with clean water. After rinsing thoroughly, dry with a soft, clean towel. A wax may then be applied.
Page 320 Original manufacturer replacement parts will provide the corrosion protection while maintaining the vehicle warranty. Any stone chips, fractures, or deep scratches in the finish should be repaired right away. Bare metal will corrode quickly and may develop into major repair expense. Minor chips and scratches can be repaired with touch-up materials available from your dealer.
Page 321 Cleaners can contain solvents that can become concentrated in the interior. Before using cleaners, read and adhere to all safety instructions on the label. While cleaning the interior, maintain adequate ventilation by opening the doors and windows. Do not clean the interior using the following cleaners or techniques: Never use a knife or any other sharp object to remove a soil...
Page 322 3. Start on the outside edge of the soil and gently rub toward the center. Continue cleaning, using a clean area of the cloth each time it becomes soiled. 4. Continue to gently rub the soiled area. 5. If the soil is not completely removed, use a mild soap solution and repeat the cleaning process with plain water.
Page 323 Some commercial products may increase gloss on the instrument panel. The increase in gloss may cause annoying reflections in the windshield and even make it difficult to see through the windshield under certain conditions. Keep belts clean and dry. Do not bleach or dye safety belts. It may severely weaken them.
Page 324 Do not place anything on top of the driver side floor mat. Use only a single floor mat on the driver side. Do not place one floor mat on top of another. Pull up on the rear of the floor mat to unlock each retainer and remove.

Buick REGAL 2011 Owner's Manual

Instruments and Controls

Infotainment

Introduction

Radio

Audio Players

Phone

Quick Links

Chapters

Related Manuals for Buick REGAL 2011

Summary of Contents for Buick REGAL 2011

Table of Contents