Table of Contents
Advertisement
FSFXXAOA1180: Installation and User Instructions
WARNING
!
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR
INJURY TO PERSON(S) OBSERVE THE FOLLOWING
1.
Use this unit only in the manner intended by the manufacturer.
If you have questions, contact the manufacturer.
2.
Before servicing or cleaning this unit, disconnect power cord
from electrical outlet.
3.
This unit is not designed to provide combustion and/or dilution
air for fuel-burning appliances.
4.
Do not use this unit with any solid-state speed control device
other than those specified in
5.
Do not operate any fan with a damaged cord or plug. Discard
fan or contact your HVAC contractor, or the manufacturer.
6.
Do not run cord under carpeting. Do not cover cord with throw
rugs, runners or similar coverings. Do not route cord under
furniture or appliances. Arrange cord away from traffic area and
where it will not be tripped over.
7.
Installation work and electrical wiring must be done by
qualified person(s) in accordance with all applicable code and
standards, including fire-rated construction.
8.
When cutting or drilling into a wall or ceiling, do not damage
electrical wiring and other hidden utilities.
9.
This unit must be grounded.
10. When performing installation, servicing or cleaning this unit, it
is recommended to wear safety glasses and gloves.
11. When applicable local regulation comprises more restrictive
installation
and/or
aforementioned requirements prevail on those of this document
and the installer agrees to conform to these at his own expenses.
12. The unit must be mounted at least 3.3 feet (1.0 meter) away
from any accessible opening of the duct.
INSTALLER INFORMATION
IMPORTANT: Ducting has a strong effect on the air flow, noise and
energy use of the fan. Use the shortest, straightest duct routing possible
for best performance, and avoid installing the fan with smaller ducts than
recommended. Insulation around the ducts can reduce energy loss and
inhibit mold growth. Fans installed with existing ducts may not achieve
their rated air flow.
NOTE: Make sure that the outdoor intake hood is easily accessible for
annual maintenance. If located above the first floor, place it close to a
window or balcony to allow ease of access.
Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations.
(Connection to the AHU on
p8).
certification
requirements,
TO AVOID UNIT DAMAGE AND ENSURE LONG LIFE
1.
Please read specification label on product for further
information and requirements.
2.
Do not intake/exhaust air into spaces within walls or ceiling or
into attics, crawl spaces, or garage. Do not attempt to recover
the exhaust air from a dryer or a range hood.
3.
Intended for residential installation only in accordance with the
requirements of NFPA 90B.
4.
When leaving the house for a long period of time (more than
two weeks), a responsible person should regularly check if the
unit operates adequately.
5.
At least once a year, the unit mechanical and electronic parts
should be inspected by qualified service personnel.
6.
Since the electronic control system of the unit uses a
microprocessor, it may not operate correctly because of external
noise or very short power failure. If this happens, unplug the
unit and wait approximately 10 seconds. Then, plug the unit in
again.
7.
Outdoor intake hood must be weather tight and comprise a bird
screen.
8.
Should you decide to dispose of this unit or of parts of it, do so
in accordance with local laws and regulation.
9.
Some areas are prone to a higher frequency of lightning-induced
power surges. Using a surge protector to protect units located in
these areas is recommended.
the
USER INFORMATION
Optional Wall Control
This unit can be connected to the supply fan wall control.
• Upon startup, the wall control LED will light up during the boot
sequence, and remain ON as the unit starts to operate after the boot
sequence. Press the push button to turn the unit OFF; the wall control
LED will also turn OFF.
• When it is time to perform the filter maintenance, the wall control
LED will blink slowly (2 seconds ON, 2 seconds OFF). After the filter
maintenance has been performed, press and hold the push button for 5
seconds to reset the filter maintenance reminder.
• Refer to your installer for any other blinking pattern.
User Servicing Instructions
• The metal filter included with this unit should be cleaned every 6
months using water and a mild soap. To remove the filter(s), open the
door, release the filter retaining clip and pull filter(s) out. Allow the
filter to dry completely before putting it back in the unit; when
reinserting it in the unit, make sure that it is standing straight.
• Inspect the outdoor air intake at least once a year.
• During the first year of operation, it is recommended to inspect your
unit at a higher frequency, especially if you live near a highway or in
an area where there is a lot of construction work, generating lots of
dust. Your filter(s) may need more frequent cleaning or replacement in
these types of environments.
• Replace the optional MERV filter at least once a year; do not attempt
to clean and reuse the optional MERV filter.
• These recommendations may change according to the environmental
conditions in your area.
2
CAUTION
!
Advertisement
Table of Contents
Troubleshooting
