Operation; Specifications; Warranty Policy - Napa Carlyle Tools 6-3802A Instruction Manual

OPERATION

Always turn off the air supply, drain
hose of air pressure and detach tool
from air supply before installing,
removing or adjusting any part or
accessory on this tool, or before per-
forming any maintenance on this tool.
Let the tool do the work. Do not put
extreme pressure on the machine. This
will only slow down the speed of the cut-
ting wheel, reduce cutting efficiency, and
put an additional burden on the motor.
Start the tool off the work, set it down on
the work evenly and move in the direction
desired to make the cut. When finished
cutting, lift off the work before stopping
the motor.
Correct cut-off wheel mounting is neces-
sary to prevent injury from broken wheels.
Do not use chipped or cracked cut-off
wheels. Cut-off wheels should be a free
fit on the spindle to prevent stress at the
hole.Use only wheel collars that come
with the tool for mounting the cutoff-
wheel. Flat washers or other adapters
may over stress the wheel.Tighten the
wheel on the spindle to prevent spin off
when the tool is turned off.
When using the cut-off tool, be careful
not to exert excessive force.Too much
force could be hazardous if it causes the
tool spindle to bend or break. The burn-
ing of the work piece or excessive speed
reduction indicates too much force being
applied. Start the tool off the work, set it
down on the work evenly and move in the
direction desired to make the cut. When
finished cutting, lift off the work before
stopping the motor.
WARRANTY
Important: DO NOT RETURN DEFECTIVE PRODUCT OUTSIDE OF ORIGINAL ONE (1) YEAR WARRANTY PERIOD TO
PLACE OF PURCHASE.

WARRANTY POLICY:

from the date of original purchase. We will replace, at our option, any part which proves to be defective in material or workman-
ship. Repairs or replacements are warranted as described above for the duration of the original warranty period. In the unlikely
event a replacement unit is required during this One (1) year period, return the unit to your local NAPA Auto Parts Store for a
replacement. This warranty does not apply to products which have been subjected to abuse, misuse, modification, neglect, lack of
maintenance, use in a production-related service, or repaired by anyone other than an Authorized Carlyle Air Tool Service Center.
For complete listing of Authorized Master Repair Centers, see enclosed Customer Warranty Repair Form, or
visit www.toolwarrantyrepair.com
6-3802A
Always use the required wheel guard to
prevent injury from broken cutting parts.
If a guard has withstood a wheel break-
age, discontinue its use and replace it
with a new guard. It may be damaged.
Position the guard between the cut-off
wheel and the operator. Use barriers to
protect others from wheel fragments and
sparks.
Always wear impact-resistant eye and
face protection to guard against flying
debris (users & bystanders). Even small
projectiles can injure eyes and cause
blindness. A cut-off wheel that breaks
can cause very serious injury. Daily mea-
sure the tool speed with a tachometer to
make sure the speed is not greater than
the RPM marked on the cut-off wheel.
Never use a cut-off wheel marked with
a speed lower than the tool speed.
NOTE: Before using, test cut-off wheel
by briefly running the tool at full throttle
under a barrier (such as under a heavy
work table) to stop any possible broken
wheel parts.
Use only wheels rated at 21,000 rpm or
higher
This Carlyle Air Tool is warranted against defects in material and workmanship for a period of One (1) Year

Specifications

Horsepower .............................. 0.5HP
Overall Length ............................. 7.6"
Width ......................................... 2.76"
Weight .................................... 1.6 lbs.
RPM ................................ 21,000 RPM
Wheel Diameter .............................. 3"
Sound Level ............................ 81dBa
Vibration Level ....................... 0.8m/s2
Air Consumption ................... 3.1CFM
Air Inlet Thread Size .......1/4"-18 NPT
Recommended Hose Size ....3/8" I.D.
Recommended
Air Pressure ................. 90psi (6.2 bar)
Air Regulator
Throttle
5
Air Inlet
Rev. 09/09/19