Related Manuals for Datavideo PD-1
Summary of Contents for Datavideo PD-1
- Page 1 PD1 19” Rack Mount Power Center User’s Guide http:// www.datavideotek.com Rev: 230506...
- Page 2 Warnings and Precautions 1. Read all of these warnings and save them for later reference. 2. Follow all warnings and instructions marked on this unit. 3. Unplug this unit from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning. 4. Do not use this unit in or near water. 5. Do not place this unit on an unstable cart, stand, or table. The unit may fall, causing serious damage. 6. Slots and openings on the cabinet top, back, and bottom are provided for ventilation. To ensure safe and reliable operation of this unit, and to protect it from overheating, do not block or cover these openings. Do not place this unit on a bed, sofa, rug, or similar surface, as the ventilation openings on the bottom of the cabinet will be blocked. This unit should never be placed near or over a heat register or radiator. This unit should not be placed in a builtin installation unless proper ventilation is provided. 7. This product should only be operated from the type of power source indicated on the marking label of the AC adapter. If you are not sure of the type of power available, consult your Datavideo dealer or your local power company. 8. Do not allow anything to rest on the power cord. Do not locate this unit where the power cord will be walked on, rolled over, or otherwise stressed. 9. If an extension cord must be used with this unit, make sure that the total of the ampere ratings on the products plugged into the extension cord do not exceed the extension cord’s rating. 10. Make sure that the total amperes of all the units that are plugged into a single wall outlet do not exceed 15 amperes. 11. Never push objects of any kind into this unit through the cabinet ventilation slots, as they may touch dangerous voltage points or short out parts that could result in risk of fire or electric shock. Never spill liquid of any kind onto or into this unit. 12. Except as specifically explained elsewhere in this manual, do not attempt to service this product yourself. Opening or removing covers that are marked “Do Not Remove” may expose you to dangerous voltage points or other risks, and will void your warranty. Refer all service issues to qualified service personnel. 13. Unplug this product from the wall outlet and refer to qualified service personnel under the ...
-
Page 3: Table Of Contents
Warranty Datavideo warrants that the equipment it manufactures shall be free from defects in material and workmanship for a period of 12 months from the date of product purchased. If equipment fails due to such defects, Datavideo will, at its option, repair or provide a replacement for the defective part or product. Equipment that fails after the warranty period, has been operated or installed in a manner other than that specified by Datavideo, or has been subjected to abuse or modification, will be repaired for time and material charges at the Buyer’s expense. This warranty does not affect your statutory rights within the Country of purchase. For EU Customers only WEEE Marking. This symbol on the product indicates that it will not be treated as household waste. It must be handed over to the applicable takeback scheme for the recycling of electrical and electronic equipment. For more detailed information about the recycling of this product, please contact your local Datavideo office. CONTENTS INTRODUCTION WHAT’S IN THE PACKAGE FRONT PANEL CONNECTIONS REAR PANEL CONNECTIONS DATAVIDEO PRODUCT VOLTAGE REQUIREMENTS SPECIFICATIONS SERVICE AND SUPPORT 2 3 3 4 6 7 8 ... -
Page 4: Introduction
Introduction The PD1 is a 19” Rack Mount Power Centre. It is able to supply multiple 12V and 5V power outputs from an 110V/220V AC Input. The PD1 is an essential accessory for Datavideo Mobile Studio applications, together with the SE800 switcher, LCD, recorders…the PD1 makes the integration of a Mobile Studio become easier and more professional. Builtin time delay power on control to initiate each DC output terminal in sequence, and installed with an autorecover fuse in every terminal to safely protect every working device. Supports input power source from AC 110V or 220V (different models) or input from the DC12V/30Amp input terminal. What’s in the Package 1. PD1 main unit 2. XLR 4P(male) to 4P(Female) 1.2m cable x 2 3. 2.1mm DC to DC Plug to 1.2m cable x 3 4. 2.1mm DC to DC Plug to 0.8m cable x 1 5. 2.1mm DC to DC Plug to 0.7m cable x 2 6. 2.1mm DC to DC Plug to 0.5m cable x 1 7. 2.1mm DC to DC Plug to 0.3m cable x 1 8. AC Power cord. 9. User’s Guide 3 ... -
Page 5: Front Panel Connections
Front Panel: External AC input. *Note: AC 110 and 220 are different models Power Switch On / Off Switch Powers the PD1 On / Off when using AC Power. N.B. From DC Power the On / Off Switch is redundant AC In with builtin fuse AC Inlet for connecting to suitable mains power outlet – 100~120V or 220~240V according to model. The socket contains a fuse holder fitted with a 10A fuse. N.B. Please ensure that you use the correct AC Voltage for the PD1 that you have purchased, 110V and 220V are different models – If you are in any doubt please contact your supplier or your local Datavideo office listed at the back of this manual. Cooling Fan The PD1 has two builtin cooling fans, please ensure that these are not blocked, and that some airflow is available. Two bypass AC outputs Two cooling fans 4 Select Input source from DC or AC External DC12Volt/30A Input ... - Page 6 AC Outlet 110V / 240V 5A 2 x AC Outlet at same voltage as AC Input (110~120 / 220~240V according to model) N.B. Sockets are redundant when PD1 is powered from DC DC In The PD1 can be powered from a suitable 12V power source. When working from DC the PD1 will not regulate the power outlets. Please ensure that the 12V power source that you use is regulated. If you intend to run the PD1 from a car or van power outlet make sure that a suitable regulator is used on the power feed. Pin 4 should be wired positive and Pin 1 should be ground. N.B. The AC Outlets are not active when the PD1 is powered via the DC In. N.B. The On / Off switch is redundant when the PD1 is powered from a DC supply. Input Select AC / DC The Input select switch can be set to AC or DC according to the power input that you intend to use. N.B. Do not connect AC and DC power inlets at the same time. 5 ...
-
Page 7: Rear Panel Connections
Rear Panel: 2.1m DC 5V/1A Output 2.1m DC 12V / 2A Output 2.1m DC 12V / 2A Output 2.1m DC12V Jack output x 2 for total 4A max rating DC Out 5V 1A 5V 1A DC Output via 2.1mm InLine Socket (Centre Positive) DC Out 12V 2A 2 x 12V 2A DC Output via 2.1mm InLine Sockets (Centre Positive) DC Out 12V 4A 4 x 12V 4A DC Output via 2.1mm InLine Sockets (Centre Positive) XLR DC12V / 5A Output XLR DC12V + 2.1m DV12V 7A Output 2.1m DC12V Jack output x 2 for total 4A max rating 6 Bypass AC Output ... -
Page 8: Datavideo Product Voltage Requirements
DC Out 12V 7A 2 x 12V 7A DC Outputs. 1 x 2.1mm InLine Sockets (Centre Positive), and 1 x 4 Pin XLR Socket (Pin 4 Positive, Pin 1 Ground) DC Out 12V 5A 1 x 12V 5A Output via 4 Pin XLR Socket (Pin 4 Positive, Pin 1 Ground) AC Outlet 1.5A 110V / 3A 240V AC Outlet at same voltage as AC Input (110~120 / 220~240V according to model) N.B. Socket is redundant when PD1 is powered from DC Ground Terminal When connecting this unit to any other component, make sure that it is properly grounded by connecting this terminal to an appropriate point. When connecting, use the socket and be sure to use wire with a crosssectional area of at least 1.0 mm2. Datavideo Product Voltage Requirements: This table is a guideline for Datavideo Products, if you are using products from other manufacturers please check their voltage requirements carefully before connecting to the PD1. DAC200, DAC100 DC 5V 1A BAC03, VP332, DAC15, DAC10, DAC6, DAC5, TLM70D, TLM404, TLM700, TLM702, TLM350, SE500, DVK100, RMC140, ITC100, DC 12V 2A STC100 DN100, CP100, DAC30 DC 12V 4A MP6000, DC 12V 5A SE800, SE800AV DC 12V 7A 7 ... -
Page 9: Specifications
Specification: ITEM VOLTAGE (AC) 110V, 220V – Separate models RANGE FREQ. INPUT POWER VOLTAGE (DC) 12V +/ 5% POWER VOLTAGE OUTPUT RANGE CURRENT EFFICIENCY INDICATOR NOISE RATIO OVERLOAD PROTECTION YES (AUTORECOVER FUSE) WORKING TEMPERATURE DIMENSION WEIGHT Specification 100~120V AC / 220~240V AC 50Hz, 60Hz 110V/5A, 220V/4A – Separate models 12V 300W +5V, +12V (depends on different loading increase voltage will some decreasing) +5V +/3%，+12V +/3% +5V/1A, +12V/2A, 4A, 5A,7A >80% LED <1% 5 ~ 45°C 440mm * 214mm * 44 mm (1U height 19” rack) 3.8Kg 8 ... -
Page 10: Service And Support
Please refer to our web site www.datavideotek.com for answers to common questions, support requests or contact your local office below. Datavideo Corporation (USA) 12300U East Washington Blvd., Whittier, CA 90606 USA Tel: +1 562 696 2324 Datavideo Technologies Europe BV Californiedreef 26 3565 BL Utrecht, The Netherlands Tel: +31 30 261 9656 Datavideo UK Limited Unit 2 Waterside Business Park, Hadfield, Glossop, Derbyshire SK13 1BE UK Tel: +44 1457 851000 Datavideo Technologies Co., Ltd. 10F, 176 JianYi Rd, Chung Ho City, Taipei Hsien, Taiwan 235 Tel: +886 2 8227 2888 Datavideo Technologies China Co. 2FD, 2 Lane 777, West Guangzhong Rd, Zhabei District, Shanghai, China Tel: +86 21 5603 6599 Datavideo Technologies (S) PTE Ltd. No. 100, Lorong 23 Geylang, #0103 D’Centennial Bldg, Singapore 388398 Tel: +65 6749 6866 Datavideo Hong Kong Limited G/F., 26 Cross Lane, Wanchai, HK Tel: +852 2833 1981 contactus@datavideo.us info@datavideo.nl sales@datavideo.co.uk service@datavideo.com.tw www.datavideo.com.tw service@datavideo.cn info@datavideo.sg info@datavideohk.com 9 www.datavideo.us www.datavideo.info www.datavideo.info www.datavideo.cn www.datavideo.info www.datavideohk.com...