Automatic Remote Control Low-Battery Warning; Two-Point Autoimmobilization - Clifford IntelliGuard Millennia Owner's Manual

Dei clifford intelliguard millennia car alarms: owners manual

Table of Contents

If your remote control battery is low, you'll hear an unusually low-pitched chirp when you remotely disarm your IntelliGuard Millennia. Replacement batteries

are available from any Authorized Clifford Dealer.

Replacement of a remote control battery is fairly easy, but any Authorized Clifford Dealer will be happy to do it for you without cost provided that you buy the

replacement battery at their shop (it's also a good idea to keep a spare of each battery in your glove box just in case).

1. Unscrew the retaining screw on the back of the remote control.

2. Carefully pry apart the remote control case with your fingernails or a small, thin screwdriver blade near the keyring opening (you may leave the keyring

in place).

3. Remove the old battery noting the + and – indications and replace it with the new one.

4. Put the enclosure back together by first aligning the LevelShift button side, then the top of the remote, then snap the case back together at the

bottom.

5. Reinsert the retaining screw but DO NOT OVERTIGHTEN.

1. Insert a small, thin screwdriver blade in the slot near the keyring opening (you may leave the keyring in place) and turn it to separate the two halves.

2. Remove the old battery noting the + and – indications and replace it with the new one.

3. Put the enclosure back together by first aligning the top of the remote, then snapping the case back together at the bottom.

While armed, your system immobilizes both the starter and ignition systems of your vehicle to prevent a thief from starting the engine. The engine will

remain immobilized even if a thief were to cut power to the system or find and remove the system control unit.

EC compliance in Europe only: Unlike the AutoArming feature noted above, AutoImmobilization occurs 30 seconds

after turning off the ignition regardless of opening/closing the doors. When you remotely disarm, you have 30

seconds to start the engine. If more than 30 seconds pass, AutoImmobilization occurs, as indicated by the LED

repeatedly flashing (but at a slower than normal "armed" rate). If AutoImmobilization occurs, use the remote

control to arm and then disarm or use the engine restart feature below.

Clifford's Wireless Immobilizer interrupts a third point in the vehicle, such as the fuel pump. This Clifford innovation provides immobilization without

any wires to the control unit, so a thief could not find the Wireless Immobilizer even if he tried tracing the system wires! Operation of the Wireless

Immobilizer is automatic and user-transparent.

BE sure to keep the record your Clifford installer provides as to the location of the Wireless Immobilizer in case your

vehicle needs future servicing.

NOTE: If your vehicle's engine ever stalls, the Wireless Immobilizer WILL engage. You must turn the ignition all the

way to "OFF" in order to restart.

In compliance with EC requirements, the AutoImmobilization will automatically engage thirty seconds after shutting down the engine. Thus

AutoImmobilization may occur while waiting for a train to pass or other delay. To restart:

1. Turn the ignition switch to the "ON" position.

2. Press button 1 of the master remote control or button

3. You may now start the engine.

If this feature is enabled and you forget to remotely arm, the system automatically arms itself 30 seconds after the vehicle doors are closed. For your

convenience, if you re-open any door(s) within the 30-second countdown, AutoArming restarts the 30-second delay from the beginning after all doors are

closed. IntelliGuard Millennia has these additional features:

feature and AutoArming are turned on, it allows you to enter the car (if it previously AutoArmed) and silently disarm the system by turning on the

ignition within 15 seconds of opening the door. See User-selectable features (column 3, row 3).

confirm the AutoArming countdown is progressing. Then, 25 seconds later, the system will AutoArm.

AutoArming. To change this setting, see User-selectable features.

AutoArming. To activate Instant AutoArming Bypass, rapidly turn the ignition switch to "ON" then "OFF." You will hear a siren chirp to confirm

that the system will not AutoArm. The system automatically reverts to its normal operating mode when you next start the engine.